Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM (for Hatchback)

ANTI-LOCK BRAKE SYSTEM (for Hatchback) > TEST MODE PROCEDURE

for Preparation Click here



WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK


    C120363E05
  1. Release the parking brake.

    NOTICE:
    Before releasing the parking brake, move the shift lever to P (for automatic transaxle model) or set chocks (for manual transaxle model) to prevent the vehicle from rolling.

    HINT:
    When the parking brake is applied or the brake fluid level is low, the brake warning light comes on.

  2. When the ignition switch is turned to ON, check that the ABS warning and brake warning lights come on for approximately 3 seconds.

    HINT:
    1. If the skid control ECU stores any DTCs, the ABS warning light will come on.
    2. If the indicator remains on or does not come on, proceed to troubleshooting for the light circuits listed below.

    Trouble Area
    See procedure
    ABS warning light circuit (Remains on)
    Click here
    ABS warning light circuit (Does not come on)
    Click here
    Brake warning light circuit (Remains on)
    Click here
    Brake warning light circuit (Does not come on)
    Click here


TEST MODE PROCEDURE (SIGNAL CHECK) (Using Intelligent Tester)

HINT:
  1. If the ignition switch is turned from ON to ACC or OFF during Test Mode (signal check), DTCs recorded during the signal check function will be cleared.
  2. During Test Mode (signal check), the skid control ECU records all DTCs of the signal check function. By performing the Test Mode (signal check), the codes are cleared if a normal condition is confirmed. The remaining codes are the codes where an abnormality was found.



  1. Procedure to enter Test Mode.

    1. Turn the ignition switch off.

    2. Check that the steering wheel is in the straight-ahead position.

    3. for Automatic transaxle: Check that the shift lever is in P and apply the parking brake.

    4. for Manual transaxle: Check that the shift lever is in neutral and apply the parking brake.

    5. Connect the intelligent tester to the DLC3.

    6. Turn the ignition switch to ON.

    7. Turn the tester on.

    8. Enter the following menus: Chassis / ABS/VSC/TRC / Signal Check.



    9. BR03904E89
    10. Check that the ABS warning light comes on for several seconds and then blinks in Test Mode.

      HINT:
      If the ABS warning light does not blink, inspect the TS and CG terminal circuit and ABS warning light circuit.

      Trouble Area
      See procedure
      ABS warning light circuit (Remains on)
      Click here
      ABS warning light circuit (Does not come on)
      Click here
      TS and CG terminal circuit
      Click here


SPEED SENSOR CHECK (Using Intelligent Tester)
  1. Check the speed sensor signal.

    1. Drive the vehicle straight-ahead.
      Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.

      1. The sensor check may not be completed if wheels pin occurs.
      2. The ABS warning light blinks when the sensor check has been completed and the brake pedal is depressed.
      3. The ABS warning light comes on immediately after a malfunction has been detected during the speed sensor check.



  2. Stop the vehicle.


    C115115E06

    NOTICE:
    1. The speed sensor check may not be completed if the speed sensor check is started while turning the steering wheel or spinning the wheels.
    2. After the ABS warning light goes off and if the vehicle speed exceeds 80 km/h (50 mph), a sensor check code will be stored again. Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).
    3. If the sensor check has not been completed, the ABS warning light blinks during driving and the ABS system does not operate.

    HINT:
    When the sensor check has been completed, the ABS warning light goes off during driving and blinks in the Test Mode pattern while the vehicle is stationary.


END OF SENSOR CHECK (Using Intelligent Tester)


    BR03904E89
  1. If the sensor check is completed, the ABS warning light blinks (Test Mode) when the vehicle stops and the ABS warning light is off while the vehicle is being driven.

    NOTICE:
    If the sensor check is not completed, the ABS warning light blinks even while the vehicle is being driven and the ABS does not operate.


READ DTC OF SIGNAL CHECK FUNCTION (Using Intelligent Tester)
  1. Read the DTC(s) by following the tester screen.

    NOTICE:
    1. If only the DTCs are displayed, repair the malfunction area and clear the DTCs.
    2. If the DTCs or Test Mode codes (DTC of signal check function) are displayed, repair the malfunction area, clear the DTCs, and perform Test Mode inspection.

    HINT:
    See the list of DTCs (See procedure "A").


TEST MODE PROCEDURE (SIGNAL CHECK) (Using SST Check Wire)

HINT:
  1. If the ignition switch is turned from ON to ACC or off during Test Mode (signal check), DTCs recorded during the signal check function will be cleared.
  2. During Test Mode (signal check), the skid control ECU records all DTCs of the signal check function. By performing the Test Mode (signal check), the codes are cleared if a normal condition is confirmed. The remaining codes are the codes where an abnormality was found.



  1. Procedure to enter Test Mode.

    1. Turn the ignition switch off.

    2. Check that the steering wheel is in the straight-ahead position.

    3. for Automatic transaxle: Check that the shift lever is in P and apply the parking brake.

    4. for Manual transaxle: Check that the shift lever is in neutral and apply the parking brake.



    5. F100115E85
    6. Using SST, connect terminals TS and CG of the DLC3.

      SST
      09843-18040  

    7. Turn the ignition switch to ON.



    8. BR03904E89
    9. Check that the ABS warning light comes on for several seconds and then blinks in Test Mode.

      HINT:
      If the ABS warning light does not blink, inspect the TS and CG terminal circuit and ABS warning light circuit.

      Trouble Area
      See procedure
      ABS warning light circuit (Remains on)
      Click here
      ABS warning light circuit (Does not come on)
      Click here
      TS and CG terminal circuit
      Click here


SPEED SENSOR CHECK (Using SST Check Wire)
  1. Check the speed sensor signal.

    1. Drive the vehicle straight-ahead.
      Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.

      1. The sensor check may not be completed if wheels pin occurs.
      2. The ABS warning light blinks when the sensor check has been completed and the brake pedal is depressed.
      3. The ABS warning light comes on immediately after a malfunction has been detected during the speed sensor check.



  2. Stop the vehicle.


    C115115E06

    NOTICE:
    1. The speed sensor check may not be completed if the speed sensor check is started while turning the steering wheel or spinning the wheels.
    2. After the ABS warning light goes off, if vehicle speed exceeds 80 km/h (50 mph), a sensor check code will be stored again. Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).
    3. If the sensor check has not been completed, the ABS warning light blinks during driving and the ABS system does not operate.

    HINT:
    When the sensor check has been completed, the ABS warning light goes off during driving and blinks in the Test Mode pattern while the vehicle is stationary.


END OF SENSOR CHECK (for Using SST Check Wire)


    BR03904E89
  1. If the sensor check is completed, the ABS warning light blinks (Test Mode) when the vehicle stops and the ABS warning light is off while the vehicle is being driven.

    NOTICE:
    If the sensor check is not completed, the ABS warning light blinks even while the vehicle is being driven and the ABS does not operate.


READ DTC OF SIGNAL CHECK FUNCTION (for Using SST Check Wire)


    F100115E87
  1. Using SST, connect terminals TC and CG of the DLC3.

    SST
    09843-18040  



  2. Count the number of blinks of the ABS warning light.


    F100113E07

    NOTICE:
    1. If only the DTCs are displayed, repair the malfunction area and clear the DTCs.
    2. If the DTCs or Test Mode codes (DTC of signal check function) are displayed, repair the malfunction area, clear the DTCs, and perform Test Mode inspection.

    HINT:
    1. If more than 1 malfunction is detected at the same time, the lowest-numbered code will be displayed first.
    2. See the list of DTCs (See procedure "A").

  3. After performing the check, disconnect SST from terminals TS and CG, and TC and CG of the DLC3 and turn the ignition switch off.

  4. Turn the ignition switch to ON.

    HINT:
    1. If the ignition switch is not turned to ON after SST is removed from the DLC3, the previous Test Mode will continue.
    2. If the ignition switch is turned to ON with terminals TS and CG shorted, the previous Test Mode will continue.


DTC OF TEST MODE (SIGNAL CHECK) FUNCTION (Procedure "A")

Test Mode DTC 
DTC Code
Tester Display/Warning Light
Detection Item
Trouble Area
Related DTC
C1271/71
Low output signal of front speed sensor RH
  1. Front speed sensor RH
  2. Sensor installation
  3. Speed sensor rotor
C1401 (Click here)
C1405 (Click here)
C1272/72
Low output signal of front speed sensor LH
  1. Front speed sensor LH
  2. Sensor installation
  3. Speed sensor rotor
C1402 (Click here)
C1406 (Click here)
C1273/73
Low output signal of rear speed sensor RH
  1. Rear speed sensor RH
  2. Sensor installation
  3. Speed sensor rotor
C1403 (Click here)
C1407 (Click here)
C1274/74
Low output signal of rear speed sensor LH
  1. Rear speed sensor LH
  2. Sensor installation
  3. Speed sensor rotor
C1404 (Click here)
C1408 (Click here)
C1275/75
Abnormal change in output signal of front speed sensor RH
Speed sensor rotor
C1413
C1414
(Click here)
C1276/76
Abnormal change in output signal of front speed sensor LH
Speed sensor rotor
C1277/77
Abnormal change in output signal of rear speed sensor RH
Speed sensor rotor
C1415
C1416
(Click here)
C1278/78
Abnormal change in output signal of rear speed sensor LH
Speed sensor rotor

HINT:
The codes in this table are output only in Test Mode (signal check).