Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM (for Hatchback)

DTC    C1425    Open in Stop Light Switch Circuit

for Preparation Click here


DESCRIPTION

The skid control ECU (housed in the actuator assembly) inputs the stop light switch signal and the condition of brake operation.
The skid control ECU has an open detection circuit, which outputs this DTC when detecting an open in the stop light input line or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).

DTC Code
DTC Detection Condition
Trouble Area
C1425
When IG1 terminal voltage is 9.5 V or more, an open circuit of the stop light switch continues for 3 seconds or more.
  1. STOP fuse
  2. Stop light switch
  3. Stop light switch circuit
  4. Brake actuator assembly (Skid control ECU)

WIRING DIAGRAM


C170217E05


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK STOP LIGHT OPERATION
  1. Check that the stop light comes on when the brake pedal is depressed, and goes off when the brake pedal is released.

    OK:
    Condition
    Illumination Condition
    Brake pedal depressed
    ON
    Brake pedal released
    OFF



NG
Go to step 6
OK


2.INSPECT SKID CONTROL ECU (STP TERMINAL)


    C168930E11
  1. Disconnect the skid control ECU connector.

  1. Inspect the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A15-28 (STP) - Body ground
    Stop light switch ON (Brake pedal depressed)
    8 to 14 V
    A15-28 (STP) - Body ground
    Stop light switch OFF (Brake pedal released)
    Below 1.5 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK


3.INSPECT SKID CONTROL ECU (IG1 TERMINAL)


    C168930E10
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A15-34 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


4.INSPECT SKID CONTROL ECU (GND TERMINAL)


    C168930E09
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A15-1 (GND1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


5.RECONFIRM DTC
  1. Reconnect the skid control ECU connector.

  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

6.INSPECT STOP LIGHT SWITCH (POWER SOURCE TERMINAL)


    C195045E01
  1. Disconnect the stop light switch connector.

  1. Inspect the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A13-2 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


7.INSPECT STOP LIGHT SWITCH


    A193650E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch pin free
    Below 1 Ω
    1 - 2
    Switch pin pushed in
    10 kΩ or higher



NG
REPLACE STOP LIGHT SWITCH (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT SWITCH)


    C195046E01
  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A15-28 (STP) - A13-1
    Always
    Below 1 Ω
    A15-28 (STP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.RECONFIRM DTC
  1. Reconnect the skid control ECU connector and the stop light switch connector.

  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK LIGHTING SYSTEM (STOP LIGHT SWITCH CIRCUIT) (Click here)