Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM (for Hatchback)

ANTI-LOCK BRAKE SYSTEM (for Hatchback) > ABS Warning Light Remains ON

for Preparation Click here


DESCRIPTION

The skid control ECU is connected to the combination meter via CAN communication.
If any of the following is detected, the ABS warning light remains on:
  1. The skid control ECU connectors are disconnected from the skid control ECU.
  2. There is a malfunction in the skid control ECU internal circuit.
  3. There is an open in the harness between the combination meter and the skid control ECU.
  4. The ABS control system is defective.

HINT:
In some cases, an intelligent tester cannot be used when the skid control ECU is abnormal.


WIRING DIAGRAM


C189929E01


INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if CAN communication system DTCs are output (Click here).
    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
CHECK CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3.CHECK BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 2NZ-FE)
    B
    NG (for 1NZ-FE)
    C



B
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY (Click here)

C
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY (Click here)
A


4.INSPECT SKID CONTROL ECU (IG1 TERMINAL)


    C168930E10
  1. Disconnect the skid control ECU connector.

  1. Inspect the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A15-34 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


5.INSPECT SKID CONTROL ECU (GND TERMINAL)


    C168930E13
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A15-1 (GND1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


6.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS WARNING LIGHT)
  1. Turn the ignition switch off.

  1. Reconnect the skid control ECU connector.

  1. Connect the intelligent tester to the DLC3.

  1. Perform Active Test of the combination meter using the intelligent tester (Click here).

    OK:
    The ABS warning light turns ON or OFF in accordance with the intelligent tester.



NG
Go to step 7
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

7.INSPECT COMBINATION METER ASSEMBLY
  1. Inspect the combination meter (Click here).
    Result 
    Result
    Proceed to
    OK
    A
    NG
    B



B
REPLACE COMBINATION METER ASSEMBLY (Click here)
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)