Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > Brake Warning Light Remains ON

for Preparation Click here


DESCRIPTION

The skid control ECU is connected to the combination meter via CAN communication.
If any of the following is detected, the brake warning light remains on:
  1. The skid control ECU connector is disconnected from the skid control ECU.
  2. The brake fluid level is insufficient.
  3. The parking brake is applied.
  4. EBD operation is not possible.

WIRING DIAGRAM


C218086E01


INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if CAN communication system DTCs are output (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
CHECK CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3.INSPECT BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V



NG
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY (Click here)
OK


4.INSPECT SKID CONTROL ECU (IG1 TERMINAL)
  1. Disconnect the A31 skid control ECU connector.

  1. Turn the ignition switch to ON.



    C213551E21
  1. Measure the voltage according to the value(s) in the table below.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Skid Control ECU)

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A31-34 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


5.INSPECT SKID CONTROL ECU (GND TERMINAL)
  1. Turn the ignition switch off.



    C213551E20
  1. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Skid Control ECU)

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A31-1 (GND1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


6.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SWITCH)
  1. Reconnect the skid control ECU connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC (Skid Control ECU) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Parking Brake SW
    Parking brake switch / ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -

  1. Using the intelligent tester, check the input of the switch operation when the parking brake pedal is operated.

    OK:
    When the parking brake is operated, the display changes as shown above.



NG
Go to step 12
OK


7.INSPECT BRAKE FLUID LEVEL WARNING SWITCH


    C216245E01
  1. Turn the ignition switch off.
    Text in Illustration 
    *1
    Component without harness connected
    (Brake Fluid Level Warning Switch)

  1. Remove the reservoir filler cap and strainer.

  1. Disconnect the brake fluid level warning switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    A float is located inside the reservoir. Its position can be changed by increasing or decreasing the level of brake fluid.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch OFF (Float up)
    10 kΩ or higher
    1 - 2
    Switch ON (Float down)
    Below 1 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Sedan)
    B
    NG (for Hatchback)
    C

    HINT:
    If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.



B
REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH) (Click here)

C
REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH) (Click here)
A


8.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH)
  1. Disconnect the D84 or D87 combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for Sedan 
    Tester Connection
    Condition
    Specified Condition
    D84-2 (SW) - A10-1
    Always
    Below 1 Ω
    D84-2 (SW) - Body ground
    Always
    10 kΩ or higher
    A10-2 - Body ground
    Always
    Below 1 Ω
    for Hatchback 
    Tester Connection
    Condition
    Specified Condition
    D87-7 (SW) - A10-1
    Always
    Below 1 Ω
    D87-7 (SW) - Body ground
    Always
    10 kΩ or higher
    A10-2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.INSPECT COMBINATION METER ASSEMBLY
  1. Connect the intelligent tester to the DLC3.

  1. Perform Active Test of the combination meter using the intelligent tester.

    1. for Sedan (Click here).
    2. for Hatchback (Click here).

    OK:
    The brake warning light turns ON or OFF in accordance with the intelligent tester.

    HINT:
    Reinstall the connectors and restore the vehicle to its prior condition before checking the combination meter.

    Result 
    Result
    Proceed to
    OK (for Sedan)
    A
    OK (for Hatchback)
    B
    NG
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
Go to step 10
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

10.REPLACE COMBINATION METER ASSEMBLY
  1. Turn the ignition switch off.

  1. Replace the combination meter.

    1. for Sedan (Click here).
    2. for Hatchback (Click here).


NEXT


11.INSPECT COMBINATION METER ASSEMBLY
  1. Connect the intelligent tester to the DLC3.

  1. Perform Active Test of the combination meter using the intelligent tester.

    1. for Sedan (Click here).
    2. for Hatchback (Click here).

    OK:
    The brake warning light turns ON or OFF in accordance with the intelligent tester.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Sedan)
    B
    NG (for Hatchback)
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

END 

12.INSPECT PARKING BRAKE SWITCH


    C212088E01
  1. Turn the ignition switch off.
    Text in Illustration 
    *1
    Component without harness connected
    (Parking Brake Switch)

  1. Disconnect the parking brake switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Parking brake switch ON
    (Switch pin free)
    Below 1 Ω
    1 - Body ground
    Parking brake switch OFF
    (Switch pin pushed in)
    10 kΩ or higher

Result 
Result
Proceed to
OK
A
NG (for Sedan)
B
NG (for Hatchback)
C


B
REPLACE PARKING BRAKE SWITCH (Click here)

C
REPLACE PARKING BRAKE SWITCH (Click here)
A


13.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARKING BRAKE SWITCH)
  1. Disconnect the 4C main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4C-2 (PKB) - D87-1
    Always
    Below 1 Ω
    4C-2 (PKB) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (for Sedan)
    A
    OK (for Hatchback)
    B
    NG
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)