Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > Slip Indicator Light Remains ON

for Preparation Click here


DESCRIPTION

The skid control ECU is connected to the combination meter via CAN communication.
Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction and VSC controls. If traction control turns OFF, the SLIP indicator light will come on.
The SLIP indicator light blinks during VSC and/or TRC operation.
When the system fails, the SLIP indicator light comes on to warn the driver (Click here).
The SLIP indicator light comes on when traction control is terminated by pressing the VSC OFF switch.

WIRING DIAGRAM


C218085E03


INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if CAN communication system DTCs are output (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
CHECK CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3.INSPECT BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V



NG
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY (Click here)
OK


4.INSPECT SKID CONTROL ECU (CSW TERMINAL)
  1. Turn the ignition switch off.



    C213551E23
  1. Disconnect the A31 skid control ECU connector.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Skid Control ECU)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A31-30 (CSW) - Body ground
    VSC OFF Switch held ON
    Below 1 Ω
    A31-30 (CSW) - Body ground
    VSC OFF Switch OFF (Not pressed)
    10 kΩ or higher



NG
Go to step 8
OK


5.INSPECT COMBINATION METER ASSEMBLY
  1. Reconnect the skid control ECU connector.

  1. Connect the intelligent tester to the DLC3.

  1. Perform Active Test of the combination meter using the intelligent tester.

    1. for Sedan (Click here).
    2. for Hatchback (Click here).

    OK:
    The SLIP indicator light turns ON or OFF in accordance with the intelligent tester.

    Result 
    Result
    Proceed to
    OK (for Sedan)
    A
    OK (for Hatchback)
    B
    NG
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
Go to step 6
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

6.REPLACE COMBINATION METER ASSEMBLY
  1. Turn the ignition switch off.

  1. Replace the combination meter.

    1. for Sedan (Click here).
    2. for Hatchback (Click here).


NEXT


7.INSPECT COMBINATION METER ASSEMBLY
  1. Connect the intelligent tester to the DLC3.

  1. Perform Active Test of the combination meter using the intelligent tester.

    1. for Sedan (Click here).
    2. for Hatchback (Click here).

    OK:
    The VSC OFF indicator light turns ON or OFF in accordance with the intelligent tester.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Sedan)
    B
    NG (for Hatchback)
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

END 

8.INSPECT VSC OFF SWITCH


    C154663E01
  1. Disconnect the VSC OFF switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (E) - 9 (+)
    Switch is pushed in
    Below 1 Ω
    6 (E) - 9 (+)
    Switch is not pushed in
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (VSC OFF Switch)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Sedan)
    B
    NG (for Hatchback)
    C



B
REPLACE VSC OFF SWITCH (Click here)

C
REPLACE VSC OFF SWITCH (Click here)
A


9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A31-30 (CSW) - D106-9 (+)
    Always
    Below 1 Ω
    A31-30 (CSW) - Body ground
    Always
    10 kΩ or higher
    D106-6 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)