Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Line for Short to +B (RHD Models)

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus line and +B when no resistance exits between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3.

Symptom
Trouble Area
No resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.
  1. Short to +B
  2. Brake actuator (skid control ECU)*1
  3. ABS and traction actuator (skid control ECU)*2
  4. Power steering ECU
  5. Steering sensor*2
  6. Yaw rate sensor*2
  7. ECM
  8. Center airbag sensor assembly
  9. Air conditioning amplifier*3
  10. Combination meter ECU
  11. Main body ECU
  1. *1: w/ ABS
  2. *2: w/ VSC
  3. *3: w/ Air conditioning

WIRING DIAGRAM


E229234E01


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.CHECK CAN BUS LINE FOR SHORT TO +B (DLC3 BRANCH WIRE)


    E191960E31
  1. Turn the ignition switch off.

  1. Disconnect the D42 D-CAN junction connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to D-CAN Junction Connector)



    E191939E15
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D15-6 (CANH) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D15-14 (CANL) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)
OK


2.CONNECT CONNECTOR
  1. Reconnect the D-CAN junction connector.


NEXT


3.CHECK CAN BUS LINE FOR SHORT TO +B (P-CAN J/C SIDE)


    E191960E32
  1. Turn the ignition switch off.

  1. Disconnect the D41 P-CAN junction connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to P-CAN Junction Connector)



    E191939E15
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D15-6 (CANH) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D15-14 (CANL) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    DLC3



NG
Go to step 14
OK


4.CHECK CAN BUS LINE FOR SHORT TO +B (P-CAN J/C - ECM)


    E191967E44
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-4 (EFI) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D41-15 (EFI) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to P-CAN Junction Connector)
    *b
    DLC3



NG
Go to step 9
OK


5.CHECK CAN BUS LINE FOR SHORT TO +B (P-CAN J/C - BRAKE ACTUATOR (SKID CONTROL ECU))

HINT:
For vehicles without ABS, go to step 6.



    E191967E45
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-1 (ABS) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D41-12 (ABS) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to P-CAN Junction Connector)
    *b
    DLC3



NG
Go to step 10
OK


6.CHECK CAN BUS LINE FOR SHORT TO +B (P-CAN J/C - ABS AND TRACTION ACTUATOR (SKID CONTROL ECU))

HINT:
For vehicles without VSC, go to step 7.



    E191967E45
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-1 (ABS) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D41-12 (ABS) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to P-CAN Junction Connector)
    *b
    DLC3



NG
Go to step 11
OK


7.CHECK CAN BUS LINE FOR SHORT TO +B (P-CAN J/C - AIR CONDITIONING AMPLIFIER)

HINT:
For vehicles without air conditioning, go to step 8.



    E191967E46
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-6 (A/C) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D41-17 (A/C) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to P-CAN Junction Connector)
    *b
    DLC3



NG
Go to step 12
OK


8.CHECK CAN BUS LINE FOR SHORT TO +B (P-CAN J/C - CENTER AIRBAG SENSOR ASSEMBLY)


    E191967E47
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-8 (A/B) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D41-19 (A/B) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to P-CAN Junction Connector)
    *b
    DLC3



NG
Go to step 13
OK

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (P-CAN J/C - D-CAN J/C (CAN-H, CAN-L)) 

9.CHECK CAN BUS LINE FOR SHORT TO +B (ECM MAIN WIRE)
E191962E04
  1. Disconnect the A21 ECM connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



    E191967E44
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-4 (EFI) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D41-15 (EFI) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to P-CAN Junction Connector)
    *b
    DLC3
    Result 
    Result
    Proceed to
    OK (for 1NZ-FE)
    A
    OK (for 2NZ-FE)
    B
    NG
    C



B
REPLACE ECM (Click here)

C
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CAN-H, CAN-L)
A

REPLACE ECM (Click here)  

10.CHECK CAN BUS LINE FOR SHORT TO +B (BRAKE ACTUATOR (SKID CONTROL ECU) BRANCH WIRE)


    E191940E35
  1. Disconnect the A76 brake actuator (skid control ECU) connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator (Skid Control ECU))



    E191967E45
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-1 (ABS) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D41-12 (ABS) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to P-CAN Junction Connector)
    *b
    DLC3



B
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BRAKE ACTUATOR (SKID CONTROL ECU) (CAN-H, CAN-L)
OK

REPLACE BRAKE ACTUATOR (SKID CONTROL ECU) (Click here)  

11.CHECK CAN BUS LINE FOR SHORT TO +B (ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) BRANCH WIRE)


    E191940E36
  1. Disconnect the A31 ABS and traction actuator (skid control ECU) connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ABS and Traction Actuator (Skid Control ECU))



    E191967E45
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-1 (ABS) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D41-12 (ABS) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to P-CAN Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) (CAN-H, CAN-L)
OK

REPLACE ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) (Click here)  

12.CHECK CAN BUS LINE FOR SHORT TO +B (AIR CONDITIONING AMPLIFIER BRANCH WIRE)


    E191964E03
  1. Disconnect the E8 air conditioning amplifier connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Conditioning Amplifier)



    E191967E46
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-6 (A/C) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D41-17 (A/C) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to P-CAN Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER (CAN-H, CAN-L)
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)  

13.CHECK CAN BUS LINE FOR SHORT TO +B (CENTER AIRBAG SENSOR ASSEMBLY BRANCH WIRE)


    E191957E07
  1. Disconnect the D16 center airbag sensor assembly connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)



    E191967E47
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-8 (A/B) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D41-19 (A/B) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to P-CAN Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CAN-H, CAN-L)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

14.CONNECT CONNECTOR
  1. Reconnect the D41 P-CAN junction connector.


NEXT


15.CHECK CAN BUS LINE FOR SHORT TO +B (D-CAN J/C - POWER STEERING ECU)


    E191967E48
  1. Disconnect the D42 D-CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-4 (EPS) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D42-15 (EPS) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to D-CAN Junction Connector)
    *b
    DLC3



NG
Go to step 20
OK


16.CHECK CAN BUS LINE FOR SHORT TO +B (D-CAN J/C - STEERING SENSOR)

HINT:
For vehicles without VSC, go to step 18.



    E191967E49
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-1 (STR) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D42-12 (STR) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to D-CAN Junction Connector)
    *b
    DLC3



NG
Go to step 21
OK


17.CHECK CAN BUS LINE FOR SHORT TO +B (D-CAN J/C - YAW RATE SENSOR)

HINT:
For vehicles without VSC, go to step 18.



    E191967E50
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-2 (YAW) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D42-13 (YAW) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to D-CAN Junction Connector)
    *b
    DLC3



NG
Go to step 22
OK


18.CHECK CAN BUS LINE FOR SHORT TO +B (D-CAN J/C - MAIN BODY ECU)


    E191967E51
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-5 (J/B) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D42-16 (J/B) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to D-CAN Junction Connector)
    *b
    DLC3



NG
Go to step 23
OK


19.CHECK CAN BUS LINE FOR SHORT TO +B (D-CAN J/C - COMBINATION METER ECU)


    E191967E52
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-7 (MET) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D42-18 (MET) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to D-CAN Junction Connector)
    *b
    DLC3



NG
Go to step 24
OK

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (D-CAN J/C - P-CAN J/C (CAN-H, CAN-L)) 

20.CHECK CAN BUS LINE FOR SHORT TO +B (POWER STEERING ECU MAIN WIRE)


    E191961E06
  1. Disconnect the D31 power steering ECU connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Steering ECU)



    E191967E48
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-4 (EPS) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D42-15 (EPS) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to D-CAN Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO POWER STEERING ECU (CAN-H, CAN-L)
OK

REPLACE POWER STEERING ECU (Click here)  

21.CHECK CAN BUS LINE FOR SHORT TO +B (STEERING SENSOR BRANCH WIRE)


    E191942E11
  1. Disconnect the D62 steering sensor connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Sensor)



    E191967E49
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-1 (STR) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D42-12 (STR) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to D-CAN Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING SENSOR (CAN-H, CAN-L)
OK

REPLACE STEERING SENSOR (Click here)  

22.CHECK CAN BUS LINE FOR SHORT TO +B (YAW RATE SENSOR BRANCH WIRE)


    E191965E08
  1. Disconnect the D107 yaw rate sensor connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate Sensor)



    E191967E50
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-2 (YAW) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D42-13 (YAW) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to D-CAN Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CAN-H, CAN-L)
OK

REPLACE YAW RATE SENSOR (Click here)  

23.CHECK CAN BUS LINE FOR SHORT TO +B (MAIN BODY ECU BRANCH WIRE)


    E191963E11
  1. Disconnect the D33 main body ECU connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Main Body ECU)



    E191967E51
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-5 (J/B) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D42-16 (J/B) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to D-CAN Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CAN-H, CAN-L)
OK

REPLACE MAIN BODY ECU 

24.CHECK CAN BUS LINE FOR SHORT TO +B (COMBINATION METER ECU BRANCH WIRE)


    E191947E19
  1. Disconnect the D1 combination meter ECU connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter ECU)



    E191967E52
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-7 (MET) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D42-18 (MET) - D15-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to D-CAN Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO COMBINATION METER (CAN-H, CAN-L)
OK

REPLACE COMBINATION METER ECU (Click here)