CAN COMMUNICATION SYSTEM > Check CAN Bus Line for Short to GND (RHD Models) |
| Symptom | Trouble Area |
| Resistance exists between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of DLC3. |
|

| 1.CHECK CAN BUS LINE FOR SHORT TO GND (DLC3 BRANCH WIRE) |
![]() |
Turn the ignition switch off.
Disconnect the D42 D-CAN junction connector.
| *a | Rear view of wire harness connector (to D-CAN Junction Connector) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D15-6 (CANH) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D15-14 (CANL) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | DLC3 |
|
| ||||
| OK | |
| 2.CONNECT CONNECTOR |
Reconnect the D-CAN junction connector.
| NEXT | |
| 3.CHECK CAN BUS LINE FOR SHORT TO GND (P-CAN J/C SIDE) |
![]() |
Turn the ignition switch off.
Disconnect the D41 P-CAN junction connector.
| *a | Rear view of wire harness connector (to P-CAN Junction Connector) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D15-6 (CANH) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D15-14 (CANL) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | DLC3 |
|
| ||||
| OK | |
| 4.CHECK CAN BUS LINE FOR SHORT TO GND (P-CAN J/C - ECM) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D41-4 (EFI) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D41-15 (EFI) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to P-CAN Junction Connector) |
| *b | DLC3 |
|
| ||||
| OK | |
| 5.CHECK CAN BUS LINE FOR SHORT TO GND (P-CAN J/C - BRAKE ACTUATOR (SKID CONTROL ECU)) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D41-1 (ABS) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D41-12 (ABS) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to P-CAN Junction Connector) |
| *b | DLC3 |
|
| ||||
| OK | |
| 6.CHECK CAN BUS LINE FOR SHORT TO GND (P-CAN J/C - ABS AND TRACTION ACTUATOR (SKID CONTROL ECU)) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D41-1 (ABS) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D41-12 (ABS) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to P-CAN Junction Connector) |
| *b | DLC3 |
|
| ||||
| OK | |
| 7.CHECK CAN BUS LINE FOR SHORT TO GND (P-CAN J/C - AIR CONDITIONING AMPLIFIER) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D41-6 (A/C) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D41-17 (A/C) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to P-CAN Junction Connector) |
| *b | DLC3 |
|
| ||||
| OK | |
| 8.CHECK CAN BUS LINE FOR SHORT TO GND (P-CAN J/C - CENTER AIRBAG SENSOR ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D41-8 (A/B) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D41-19 (A/B) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to P-CAN Junction Connector) |
| *b | DLC3 |
|
| ||||
| OK | ||
| ||
| 9.CHECK CAN BUS LINE FOR SHORT TO GND (ECM MAIN WIRE) |
![]() |
Disconnect the A21 ECM connector.
| *a | Front view of wire harness connector (to ECM) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D41-4 (EFI) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D41-15 (EFI) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to P-CAN Junction Connector) |
| *b | DLC3 |
| Result | Proceed to |
| OK (for 1NZ-FE) | A |
| OK (for 2NZ-FE) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 10.CHECK CAN BUS LINE FOR SHORT TO GND (BRAKE ACTUATOR (SKID CONTROL ECU) BRANCH WIRE) |
![]() |
Disconnect the A15 brake actuator (skid control ECU) connector.
| *a | Front view of wire harness connector (to Brake Actuator (Skid Control ECU)) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D41-1 (ABS) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D41-12 (ABS) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to P-CAN Junction Connector) |
| *b | DLC3 |
|
| ||||
| OK | ||
| ||
| 11.CHECK CAN BUS LINE FOR SHORT TO GND (ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) BRANCH WIRE) |
![]() |
Disconnect the A31 ABS and traction actuator (skid control ECU) connector.
| *a | Front view of wire harness connector (to ABS and Traction Actuator (Skid Control ECU)) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D41-1 (ABS) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D41-12 (ABS) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to P-CAN Junction Connector) |
| *b | DLC3 |
|
| ||||
| OK | ||
| ||
| 12.CHECK CAN BUS LINE FOR SHORT TO GND (AIR CONDITIONING AMPLIFIER BRANCH WIRE) |
![]() |
Disconnect the E8 air conditioning amplifier connector.
| *a | Front view of wire harness connector (to Air Conditioning Amplifier) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D41-6 (A/C) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D41-17 (A/C) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to P-CAN Junction Connector) |
| *b | DLC3 |
|
| ||||
| OK | ||
| ||
| 13.CHECK CAN BUS LINE FOR SHORT TO GND (CENTER AIRBAG SENSOR ASSEMBLY BRANCH WIRE) |
![]() |
Disconnect the D16 center airbag sensor assembly connector.
| *a | Front view of wire harness connector (to Center Airbag Sensor Assembly) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D41-8 (A/B) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D41-19 (A/B) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to P-CAN Junction Connector) |
| *b | DLC3 |
|
| ||||
| OK | ||
| ||
| 14.CONNECT CONNECTOR |
Reconnect the P-CAN junction connector.
| NEXT | |
| 15.CHECK CAN BUS LINE FOR SHORT TO GND (D-CAN J/C - POWER STEERING ECU) |
![]() |
Disconnect the D42 D-CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D42-4 (EPS) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D42-15 (EPS) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to D-CAN Junction Connector) |
| *b | DLC3 |
|
| ||||
| OK | |
| 16.CHECK CAN BUS LINE FOR SHORT TO GND (D-CAN J/C - STEERING SENSOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D42-1 (STR) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D42-12 (STR) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to D-CAN Junction Connector) |
| *b | DLC3 |
|
| ||||
| OK | |
| 17.CHECK CAN BUS LINE FOR SHORT TO GND (D-CAN J/C - YAW RATE SENSOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D42-2 (YAW) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D42-13 (YAW) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to D-CAN Junction Connector) |
| *b | DLC3 |
|
| ||||
| OK | |
| 18.CHECK CAN BUS LINE FOR SHORT TO GND (D-CAN J/C - MAIN BODY ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D42-5 (J/B) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D42-16 (J/B) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to D-CAN Junction Connector) |
| *b | DLC3 |
|
| ||||
| OK | |
| 19.CHECK CAN BUS LINE FOR SHORT TO GND (D-CAN J/C - COMBINATION METER ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D42-7 (MET) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D42-18 (MET) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to D-CAN Junction Connector) |
| *b | DLC3 |
|
| ||||
| OK | ||
| ||
| 20.CHECK CAN BUS LINE FOR SHORT TO GND (POWER STEERING ECU MAIN WIRE) |
![]() |
Disconnect the D31 power steering ECU connector.
| *a | Rear view of wire harness connector (to Power Steering ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D42-4 (EPS) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D42-15 (EPS) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to D-CAN Junction Connector) |
| *b | DLC3 |
|
| ||||
| OK | ||
| ||
| 21.CHECK CAN BUS LINE FOR SHORT TO GND (STEERING SENSOR BRANCH WIRE) |
![]() |
Disconnect the D62 steering sensor connector.
| *a | Front view of wire harness connector (to Steering Sensor) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D42-1 (STR) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D42-12 (STR) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to D-CAN Junction Connector) |
| *b | DLC3 |
|
| ||||
| OK | ||
| ||
| 22.CHECK CAN BUS LINE FOR SHORT TO GND (YAW RATE SENSOR BRANCH WIRE) |
![]() |
Disconnect the D107 yaw rate sensor connector.
| *a | Front view of wire harness connector (to Yaw Rate Sensor) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D42-2 (YAW) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D42-13 (YAW) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to D-CAN Junction Connector) |
| *b | DLC3 |
|
| ||||
| OK | ||
| ||
| 23.CHECK CAN BUS LINE FOR SHORT TO GND (MAIN BODY ECU BRANCH WIRE) |
![]() |
Disconnect the D33 main body ECU connector.
| *a | Rear view of wire harness connector (to Main Body ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D42-5 (J/B) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D42-16 (J/B) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to D-CAN Junction Connector) |
| *b | DLC3 |
|
| ||||
| OK | ||
| ||
| 24.CHECK CAN BUS LINE FOR SHORT TO GND (COMBINATION METER ECU BRANCH WIRE) |
![]() |
Disconnect the D1 combination meter ECU connector.
| *a | Rear view of wire harness connector (to Combination Meter ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D42-7 (MET) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| D42-18 (MET) - D15-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to D-CAN Junction Connector) |
| *b | DLC3 |
|
| ||||
| OK | ||
| ||