DTC B1628/82 Front Passenger Side - Side Airbag Sensor Assembly Initialization Incomplete |
DTC B1648/82 Front Passenger Side Satellite Sensor Bus Initialization Incomplete |
| DTC Code | Detection Condition | Trouble Area |
| B1628/82 B1648/82 | When one of following conditions is met:
|
|


| 1.CHECK PAST DTC |
Turn the ignition switch to ON, and wait for at least 60 seconds.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check the past DTCs (Click here).
| Result | Proceed to |
| DTC B1622 or B1627 is output | A |
| DTC B1632 or B1637 is output | B |
| DTC B1622, B1627, B1632 and B1637 are not output | C |
|
| ||||
|
| ||||
| C | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and front passenger side - side airbag sensor.
|
| ||||
| OK | |
| 3.CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor assembly and front passenger side - side airbag sensor.
Check that the connectors (on the center airbag sensor side and front passenger side - side airbag sensor side) are not damaged.
|
| ||||
| OK | |
| 4.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - SIDE AIRBAG SENSOR) |

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J16-4 (BBR+) - Body ground | Ignition switch ON | Below 1 V |
| J16-3 (BBR-) - Body ground | Ignition switch ON | Below 1 V |
| Tester Connection | Switch Condition | Specified Condition |
| J17-4 (BBL+) - Body ground | Ignition switch ON | Below 1 V |
| J17-3 (BBL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Using a service wire, connect terminals 8 (BBP+) and 11 (BBP-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J16-4 (BBR+) - J16-3 (BBR-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| J17-4 (BBL+) - J17-3 (BBL-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J16-4 (BBR+) - J16-3 (BBR-) | Always | 1 MΩ or higher |
| J16-4 (BBR+) - Body ground | Always | 1 MΩ or higher |
| J16-3 (BBR-) - Body ground | Always | 1 MΩ or higher |
| Tester Connection | Condition | Specified Condition |
| J17-4 (BBL+) - J17-3 (BBL-) | Always | 1 MΩ or higher |
| J17-4 (BBL+) - Body ground | Always | 1 MΩ or higher |
| J17-3 (BBL-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 5.CHECK CONNECTION OF CONNECTORS |
Check that the connector is properly connected to the front passenger side rear airbag sensor.
|
| ||||
| OK | |
| 6.CHECK CONNECTORS |
Disconnect the connectors from the front passenger side - side airbag sensor and front passenger side rear airbag sensor.
Check that the connector (on the front passenger side rear airbag sensor side) is not damaged.
|
| ||||
| OK | |
| 7.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR - REAR AIRBAG SENSOR) |

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J16-1 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| J16-2 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
| Tester Connection | Switch Condition | Specified Condition |
| J17-1 (BCL+) - Body ground | Ignition switch ON | Below 1 V |
| J17-2 (BCL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Using a service wire, connect terminals 2 and 1 of connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J16-1 (BCR+) - J16-2 (BCR-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| J17-1 (BCL+) - J17-2 (BCL-) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J16-1 (BCR+) - J16-2 (BCR-) | Always | 1 MΩ or higher |
| J16-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| J16-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
| Tester Connection | Condition | Specified Condition |
| J17-1 (BCL+) - J17-2 (BCL-) | Always | 1 MΩ or higher |
| J17-1 (BCL+) - Body ground | Always | 1 MΩ or higher |
| J17-2 (BCL-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 8.CHECK FRONT PASSENGER SIDE - SIDE AIRBAG SENSOR |
![]() |
Interchange the driver side - side airbag sensor with front passenger side - side airbag sensor and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 90 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1623, B1628, B1643 and B1648 are not output | A |
| DTC B1623 or B1643 is output | B |
| DTC B1628 or B1648 is output | C |
|
| ||||
|
| ||||
| C | |
| 9.CHECK FRONT PASSENGER SIDE REAR AIRBAG SENSOR |
![]() |
Interchange the driver side rear airbag sensor with front passenger side rear airbag sensor and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 90 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1623 or B1643 is output | A |
| DTC B1628 or B1648 is output | B |
| DTC B1623, B1628, B1643 and B1648 are not output | C |
|
| ||||
|
| ||||
| C | ||
| ||