DTC P0420 Catalyst System Efficiency Below Threshold (Bank 1) |


| DTC No. | DTC Detection Condition | Trouble Area |
| P0420 | The ratio of the signal lengths (the signal length of heated oxygen sensor (sensor 2) divided by the signal length of heated oxygen sensor (sensor 1)) smaller than standard value (2 trip detection logic) |
|

| *1 | Exhaust Manifold | *2 | Heated Oxygen Sensor (Sensor 1) |
| *3 | Front Exhaust Pipe Assembly (TWC: Front and Rear Catalyst) | *4 | Heated Oxygen Sensor (Sensor 2) |
| *5 | Tail Exhaust Pipe Assembly | - | - |
| Required Sensors/Components (Main) | Catalyst |
| Required Sensors/Components (Related) | Heated oxygen sensor, Intake air temperature sensor, Mass air flow meter, Crankshaft position sensor, Engine coolant temperature sensor |
| Frequency of Operation | Once per driving cycle |
| Accumulated time that all of following conditions are met | 30 seconds |
| Battery voltage | 11 V or more |
| Intake air temperature | -10°C (14°F) or more |
| Idle status | OFF |
| Engine speed | Less than 4000 rpm |
| Engine coolant temperature | 75°C (167°F) or more |
| Fuel system status | Closed loop |
| Front catalyst temperature | 530°C (986°F) or more |
| Rear catalyst temperature | 530°C (986°F) or more |
| Heated oxygen sensor (sensor 2) locus length | 0.45 V or more (varies with heated oxygen sensor locus length) |
| Frequency of the monitor | 3 times |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|


| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
| DTC P0420 is output | A |
| DTC P0420 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up.
Turn the tester on.
Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of the heated oxygen sensor (O2S B1S1 and O2S B1S2) displayed on the tester.
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| O2S B1S1 (Heated oxygen sensor (sensor 1)) | +12% | Rich | Higher than 0.5 V |
| -12% | Lean | Below 0.4 V | |
| O2S B1S2 (Heated oxygen sensor (sensor 2)) | +12% | Rich | Higher than 0.5 V |
| -12% | Lean | Below 0.4 V |
| Status O2S B1S1 | Status O2S B1S2 | Actual Air Fuel Ratio, Heated Oxygen Sensor Condition | Misfire | Main Suspected Trouble Area | Proceed to |
| Lean/Rich | Lean/Rich | Normal | - |
| A |
| Lean | Lean/Rich | Heated oxygen sensor (sensor 1) malfunction | - |
| B |
| Rich | Lean/Rich | Heated oxygen sensor (sensor 1) malfunction | - |
| |
| Lean/Rich | Lean | Heated oxygen sensor (sensor 2) malfunction | - |
| C |
| Lean/Rich | Rich | Heated oxygen sensor (sensor 2) malfunction | - |
| |
| Lean | Lean | Actual air-fuel ratio lean | May occur |
| D |
| Rich | Rich | Actual air-fuel ratio rich | - |
|
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 4.REPLACE EXHAUST PIPE ASSEMBLY FRONT (TWC: FRONT AND REAR CATALYST) |
Replace the exhaust pipe assembly front (TWC: Front and rear catalyst) (Click here).
| NEXT | ||
| ||
| 5.REPLACE HEATED OXYGEN SENSOR (SENSOR 1) |
Replace the heated oxygen sensor (sensor 1) (Click here).
|
| ||||
| 6.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 7.REPLACE HEATED OXYGEN SENSOR (SENSOR 2) |
Replace the heated oxygen sensor (sensor 2) (Click here).
|
| ||||
| 8.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO |
Check the cause of extremely rich or lean actual air-fuel ratio, referring to the DTC P0171 Inspection Procedure .
|
| ||||
| 10.REPAIR OR REPLACE EXHAUST GAS LEAK POINT |
Repair or replace the exhaust gas leak point (Click here).
| NEXT | |
| 11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the tester on.
Start the engine.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0420 is output | A |
| DTC is not output (No pending DTCs output) | B |
|
| ||||
| A | |
| 12.REPLACE EXHAUST PIPE ASSEMBLY FRONT (TWC: FRONT AND REAR CATALYST) |
Replace the exhaust pipe assembly front (TWC: Front and rear catalyst) (Click here).
| NEXT | ||
| ||