Home › Engine / Hybrid System · 2NZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0171    System Too Lean (Bank 1)

DTC    P0172    System Too Rich (Bank 1)

for Preparation Click here


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim includes the short-term fuel trim and the long-term fuel trim.
The short-term fuel trim is the short-term fuel compensation used to maintain the air-fuel ratio at the stoichiometric air-fuel ratio. The signal from the heated oxygen sensor indicates whether the air-fuel ratio is rich or lean compared to the stoichiometric air-fuel ratio. This variance triggers a reduction in the fuel volume if the air-fuel ratio is rich, and an increase in the fuel volume if it is lean.
The short-term fuel trim varies from the central value due to individual engine differences, wear over time and changes in the operating environment. The long-term fuel trim, which controls overall fuel compensation, steadies long-term deviations of the short-term fuel trim from the central value.
If both the short-term fuel trim and the long-term fuel trim are lean or rich beyond a certain value, the ECM determines this to be a malfunction, illuminates the MIL and stores a DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0171
When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on lean side (2 trip detection logic)
  1. Intake system
  2. Injector blockage
  3. Mass air flow meter
  4. Engine coolant temperature sensor
  5. Fuel pressure
  6. Gas leakage in exhaust system
  7. Heated oxygen sensor (sensor 1)
  8. Heated oxygen sensor (sensor 1) heater
  9. No. 1 integration relay
  10. PCV valve and hose
  11. ECM
  12. Wire harness
P0172
When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on rich side (2 trip detection logic)
  1. Injector leak or blockage
  2. Mass air flow meter
  3. Engine coolant temperature sensor
  4. Ignition system
  5. Fuel pressure
  6. Gas leakage in exhaust system
  7. Heated oxygen sensor (sensor 1)
  8. Heated oxygen sensor (sensor 1) heater
  9. No. 1 integration relay
  10. ECM
  11. Wire harness

HINT:
  1. When DTC P0171 is recorded, the actual air-fuel ratio is on the lean side. When DTC P0172 is recorded, the actual air-fuel ratio is on the rich side.
  2. If the vehicle runs out of fuel, the air-fuel ratio is lean and DTC P0171 may be recorded. The MIL is then illuminated.
  3. If the total of the short-term fuel trim value and long-term fuel trim value is within the malfunction threshold (and engine coolant temperature is more than 75°C (167°F)), the system is functioning normally.


MONITOR DESCRIPTION

Under closed loop fuel control, fuel injection amounts that deviate from the ECM's estimated fuel amount will cause a change in the long-term fuel trim compensation value. Long-term fuel trim value is adjusted when persistent deviations in the short-term fuel trim's value are present. Also, the smoothed fuel trim learning value is adjusted when deviations from the ECM's simulated fuel injection value are present. The smoothed fuel trim learning value is a combination of smoothed short-term fuel trim (fuel feedback compensation value) and smoothed long-term fuel trim (learning value of the air-fuel ratio). When the smoothed fuel trim learning value exceeds the malfunction threshold, the ECM interprets this as a fault in the fuel system and stores a DTC.
Example:
The smoothed fuel trim learning value is above 48% or below -35%. The ECM interprets this as a fault in the fuel system.

A082386E60


MONITOR STRATEGY


Required Sensors/Components
Heated oxygen sensor, Mass air flow meter, Crankshaft position sensor
Frequency of Operation
Continuous

TYPICAL ENABLING CONDITIONS


Fuel system status
Closed loop
Battery voltage
11 V or higher
Either of following conditions 1 or 2 met
-
1. Engine RPM
Less than 1000 rpm
2. Intake air amount per revolution
0.09 g/rev or more

TYPICAL MALFUNCTION THRESHOLDS


Purge-cut
Executing
Either of following conditions 1 or 2 met
-
1. Average of short-term fuel trim and long-term fuel trim
48% or more (varies with engine coolant temperature)
2. Average of short-term fuel trim and long-term fuel trim
-35% or more (varies with engine coolant temperature)

CONFIRMATION DRIVING PATTERN


A199233E93

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn tester on [A].
  6. Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher) with all the accessories switched off [B].
  7. With the engine warmed up, idle the engine for 2 minutes or more [C].
  8. Drive the vehicle at between 60 and 120 km/h (37 and 75 mph) and at an engine speed of between 1400 and 3200 rpm for 5 minutes or more [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  9. Enter the following menus: Powertrain / Engine and ECT / DTC [E].
  10. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.


WIRING DIAGRAM

Refer to P0031 , P0100 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Sensor 1 refers to the sensor closest to the engine assembly.
  2. Sensor 2 refers to the sensor farthest away from the engine assembly.
  3. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  4. A low heated oxygen sensor (sensor 1) voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
  5. A high heated oxygen sensor (sensor 1) voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0171 OR P0172)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC P0171 or P0172 is output
    A
    DTC P0171 or P0172 and other DTCs are output
    B



B
GO TO DTC CHART (Click here)
A


2.CHECK CONNECTION OF PCV HOSE
  1. Check the PCV hose connection (Click here).

OK:
PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leaks in intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

  1. Perform the Control the Injection Volume with the engine idling.

  1. Monitor the output voltages of the heated oxygen sensors (O2S B1S1 and O2S B1S2) displayed on the tester.

    HINT:
    1. Change the fuel injection volume within the range of -12% to +12%. The injection volume can be changed in fine gradations.
    2. The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.
    3. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


    Tester Display (Sensor)
    Injection Volume
    Status
    Voltage
    O2S B1S1
    (Heated oxygen sensor (sensor 1))
    +12%
    Rich
    Higher than 0.5 V
    -12%
    Lean
    Below 0.4 V
    O2S B1S2
    (Heated oxygen sensor (sensor 2))
    -12%
    Rich
    Higher than 0.5 V
    -12%
    Lean
    Below 0.4 V

    Status of O2S B1S1
    Status of O2S B1S2
    Air-Fuel Ratio Condition and
    Heated Oxygen Sensor Condition
    Suspected Trouble Area
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    -
    Lean
    Lean
    Actual air-fuel ratio lean
    1. PCV valve and hose
    2. PCV hose connections
    3. Fuel injector blockage
    4. Gas leak from exhaust system
    5. Intake system
    6. Fuel pressure
    7. Mass air flow meter
    8. Engine coolant temperature sensor
    A
    Rich
    Rich
    Actual air-fuel ratio rich
    1. Fuel injector leak or blockage
    2. Gas leak from exhaust system
    3. Ignition system
    4. Fuel pressure
    5. Mass air flow meter
    6. Engine coolant temperature sensor
    Lean
    Lean/Rich
    Heated oxygen sensor (sensor 1) malfunction
    1. Heated oxygen sensor (sensor 1) malfunction
    B
    Rich
    Lean/Rich
    Heated oxygen sensor (sensor 1) malfunction
    1. Heated oxygen sensor (sensor 1) malfunction

HINT:
Lean: During Control the Injection Volume of the Active Test, the output voltage of the heated oxygen sensor (sensor 1) almost always indicates 0.4 V or less.
Rich: During Control the Injection Volume of the Active Test, the output voltage of the heated oxygen sensor (sensor 1) almost always indicates 0.5 V or more.
Lean/Rich: During Control the Injection Volume of the Active Test, the output voltage of the heated oxygen sensor (sensor 1) alternates correctly.



B
Go to step 11
A


5.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Coolant Temp value when the engine is cold and warmed up.

    Standard:

    Tester Display
    Condition
    Specified Condition
    Coolant Temp
    Cold engine
    Same as ambient air temperature
    Warm engine
    Between 80 and 100°C (176 and 212°F)



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


6.READ VALUE USING INTELLIGENT TESTER (MAF)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF, Coolant Temp and Engine speed.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 3000 rpm.

    Standard:

    Tester Display
    Condition
    Specified Condition
    MAF
    Shift lever position: N
    A/C: OFF
    Engine speed: 3000 rpm
    Between 4.0 gm/sec and 8.0 gm/sec



NG
Go to step 17
OK


7.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


8.CHECK EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

OK:
No gas leaks.



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


9.CHECK FOR SPARK AND IGNITION
  1. Perform a spark test .

HINT:
  1. If the result of the spark test is normal, proceed to the next step.
  2. If the spark plugs or ignition system malfunction, engine misfire may occur. The misfire counter can be read with the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count to #4.


NEXT


10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
  1. Check the injection and volume.

HINT:
  1. Refer to the fuel injector inspection procedure (Click here).
  2. If the injectors are malfunctioning, engine misfire may occur. The misfire counter can be read with the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count to #4.



OK
Go to step 15

NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)

11.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE OF HEATED OXYGEN SENSOR (SENSOR 1))
  1. Inspect the heated oxygen sensor (sensor 1) (Click here).



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1))
A079114E47
  1. Disconnect the heated oxygen sensor (sensor 1) connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B37-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Heated Oxygen Sensor (Sensor 1))



NG
Go to step 22
OK


13.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)
  1. Disconnect the heated oxygen sensor (sensor 1) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B37-1 (HT1A) - B84-109 (HT1A)
    Always
    Below 1 Ω
    B37-3 (OX1A) - B84-112 (OX1A)
    Always
    Below 1 Ω
    B37-4 (E2) - B84-90 (EX1A)
    Always
    Below 1 Ω
    B37-1 (HT1A) or B84-109 (HT1A) - Body ground
    Always
    10 kΩ or higher
    B37-3 (OX1A) or B84-112 (OX1A) - Body ground
    Always
    10 kΩ or higher
    B37-4 (E2) or B84-90 (EX1A) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.REPLACE HEATED OXYGEN SENSOR (SENSOR 1)
  1. Replace the heated oxygen sensor (sensor 1) (Click here).


NEXT


15.PERFORM CONFIRMATION DRIVING PATTERN
  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


NEXT


16.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0171 or P0172 is output
    A
    DTC is not output
    B



B
END
A


17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
  1. Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


18.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0171 or P0172 is output
    A
    DTC is not output
    B



B
END
A


19.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B72-3 (VG) - B84-118 (VG)
    Always
    Below 1 Ω
    B72-2 (E2G) - B84-116 (E2G)
    Always
    Below 1 Ω
    B72-3 (VG) or B84-118 (VG) - Body ground
    Always
    10 kΩ or higher
    B72-2 (E2G) or B84-116 (E2G) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


20.REPLACE MASS AIR FLOW METER
  1. Replace mass air flow meter (Click here).

    HINT:
    If the result of the inspection performed in step 6 indicated no problem, proceed to the next step without replacing the mass air flow meter.


NEXT


21.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0171 or P0172 is output
    B



B
REPLACE ECM (Click here)
A

END 

22.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - NO. 1 INTEGRATION RELAY)
  1. Disconnect the heated oxygen sensor (sensor 1) connector.

  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B37-2 (+B) - 1E-4
    Always
    Below 1 Ω
    B37-2 (+B) or 1E-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)