Home › Engine / Hybrid System · 1NZ-FE › ENGINE CONTROL › 1NZ-FE SFI SYSTEM

DTC    P0300    Random / Multiple Cylinder Misfire Detected

DTC    P0301    Cylinder 1 Misfire Detected

DTC    P0302    Cylinder 2 Misfire Detected

DTC    P0303    Cylinder 3 Misfire Detected

DTC    P0304    Cylinder 4 Misfire Detected

for Preparation Click here


DESCRIPTION

A093767E09
When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the Three-Way Catalytic Converter (TWC) temperature, which may cause damage to the TWC. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the TWC reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0300
When one of following conditions is detected (2 trip detection logic):
  1. High temperature misfire occurs in three-way catalytic converter (MIL blinks)
  2. Emission deterioration misfire occurs (MIL illuminates)
  3. Simultaneous misfiring of several cylinders occurs
  1. Open or short in engine wire harness
  2. Connector connections
  3. Vacuum hose connections
  4. Ignition system
  5. Fuel injector assembly
  6. Fuel pressure
  7. Fuel line
  8. Fuel pump
  9. Mass air flow meter
  10. Engine coolant temperature sensor
  11. Compression pressure
  12. Valve timing
  13. PCV valve and hose
  14. PCV hose connections
  15. Intake system
  16. ECM
P0301
P0302
P0303
P0304
When one of following conditions is detected (2 trip detection logic):
  1. High temperature misfire occurs in three-way catalytic converter (MIL blinks)
  2. Emission deterioration misfire occurs (MIL illuminates)
  3. Misfiring of specific cylinder occurs
When DTCs for misfiring cylinders are randomly stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when the following condition, which could cause catalyst deterioration, is detected (2 trip detection logic).
  1. An excessive misfiring rate (approximately 20 to 50 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL immediately when the following condition, which could cause three-way catalytic converter damage, is detected. Also, the ECM stores a DTC when the following condition is detected (2 trip detection logic).
  1. A sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.

MONITOR STRATEGY


Required Sensors/Components (Main)
Camshaft position sensor and Crankshaft position sensor
Required Sensors/Components (Related)
Engine coolant temperature and intake air temperature sensors and Mass air flow meter
Frequency of Operation
Continuous

TYPICAL ENABLING CONDITIONS


Misfire: 
Intake air temperature
-10°C or higher
Either of following conditions (a) or (b) met
-
(a)Engine coolant temperature at engine start
Higher than -7°C (19°F)
(b) Engine coolant temperature
Higher than 20°C (68°F)

Monitor period of emission-related misfire: 
Duration
Crankshaft 1000 revolution x 4

Monitor period of catalyst-damaged misfire (MIL blinks): 
Duration
Crankshaft 200 revolution x 3

WIRING DIAGRAM

Refer to DTC P0100 .
Refer to Fuel Injector Circuit .

CONFIRMATION DRIVING PATTERN

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the tester on.
  4. Record the DTC(s) and freeze frame data.
  5. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  6. Switch the ECM from normal mode to check mode (Click here).
  7. Read the misfire counts of each cylinder, Cylinder #1 Misfire Count to Cylinder #4 Misfire Count, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
  8. Drive the vehicle several times with the conditions, such as engine speed and engine load, shown in Misfire RPM and Misfire Load in the Data List.

    HINT:
    1. In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, using the Misfire RPM and Misfire Load in the Data List.

    Engine Speed (rpm)
    Duration
    Idling
    8.0 minutes or more
    1000
    4.5 minutes or more
    2000
    2.5 minutes or more
    3000
    1.5 minutes or more

  9. Check whether misfires have occurred by checking DTCs and freeze frame data.

    HINT:
    Do not turn the ignition switch off until the stored DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data will be cleared.

  10. Record the DTC(s), freeze frame data and misfire counts.
  11. Turn the ignition switch off and wait for at least 5 seconds.
  12. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.
  4. If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors is considered to be a possible cause of the problem:
    1. There was insufficient fuel in the tank.
    2. Improper fuel is used.
    3. The spark plugs have been contaminated.
  5. After finishing repairs, check the misfire counts of the cylinders Cylinder #1 Misfire Count to Cylinder #4 Misfire Count.
  6. Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after finishing repairs.
  7. When one of Short FT #1 or Long FT #1 in the freeze frame data is outside the range of +/-15%, the air-fuel ratio may be Rich (-15% or less) or Lean (+15% or more).
  8. When the Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfires have occurred only while warming up the engine.
  9. An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be detected.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    HINT:
    Write down the indicated DTCs.


    Result 
    Result
    Proceed to
    DTC P0300, P0301, P0302, P0303 and/or P0304 are output
    A
    DTC P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output
    B

HINT:
If any DTCs other than P0300, P0301, P0302, P0303 and P0304 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK PCV HOSE (HOSE CONNECTIONS)
  1. Check the PCV hose connections (Click here).

OK:
PCV hose is correctly connected and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3.READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire RPM and Misfire Load.

  1. Read and note the Misfire RPM and Misfire Load values.

    HINT:
    The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.


NEXT


4.READ VALUE USING INTELLIGENT TESTER (CYLINDER #1 MISFIRE COUNT, #2, #3 AND #4)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count, Cylinder #2 Misfire Count, Cylinder #3 Misfire Count and Cylinder #4 Misfire Count.

  1. Start the engine and allow the engine to idle.

  1. Read each value for Cylinder #1 (to #4) Misfire Count displayed on the tester. If no misfire counts occur in any cylinders, perform the following procedures:

    1. Move the shift lever to first gear.

    2. Check the Cylinder #1 (to #4) Misfire Count.

    3. If misfire counts are still not displayed, perform steps "A" and "B", and then check the misfire counts again. Procedure A: Drive the vehicle while satisfying the Misfire RPM and Misfire Load values noted in the "Read Value Using intelligent tester (Misfire RPM and Misfire Load)" procedure above. Procedure B: Check the Cylinder #1 (to#4) Misfire Count.


Result 
Result
Proceed to
Most misfires occur in only 1 or 2 cylinders
A
3 cylinders or more have equal misfire counts
B

HINT:
  1. If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
  2. If the freeze frame data record of the engine coolant temperature is below 75°C (167°F), it may only be possible to detect the misfire when the engine is cold.
  3. If the freeze frame data record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.



B
Go to step 16
A


5.INSPECT SPARK PLUG
  1. Inspect the spark plug of the misfiring cylinder .



NG
REPLACE SPARK PLUG
OK


6.CHECK FOR SPARKS (SPARK TEST)
  1. Perform a spark test (Click here).

    HINT:
    If the result of the spark test is normal, proceed to the next step.


NEXT


7.CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


8.INSPECT FUEL INJECTOR ASSEMBLY (POWER SOURCE)


    A200903E28
  1. Disconnect the fuel injector assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B5-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B7-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B9-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B11-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)



NG
CHECK FUEL INJECTOR CIRCUIT (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
  1. Disconnect the fuel injector assembly connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B5-2 - B84-108 (#10)
    Always
    Below 1 Ω
    B7-2 - B84-107 (#20)
    Always
    Below 1 Ω
    B9-2 - B84-106 (#30)
    Always
    Below 1 Ω
    B11-2 - B84-105 (#40)
    Always
    Below 1 Ω
    B5-2 or B84-108 (#10) - Body ground
    Always
    10 Ω or higher
    B7-2 or B84-107 (#10) - Body ground
    Always
    10 Ω or higher
    B9-2 or B84-106 (#10) - Body ground
    Always
    10 Ω or higher
    B11-2 or B84-105 (#10) - Body ground
    Always
    10 Ω or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
  1. Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


11.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks .

    OK:
    No leaks in intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM (Click here)
OK


12.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 31
OK


13.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Data List twice, when the engine is both cold and warmed up.

    Standard:

    Tester Display
    Condition
    Specified Condition
    Coolant Temp
    Cold engine
    Same as ambient air temperature
    Warm engine
    Between 80 and 100°C (176 and 212°F)



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


14.READ VALUE USING INTELLIGENT TESTER (MAF)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF and Coolant Temp.

  1. Allows the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed 3000 rpm.

    Standard:

    Tester Display
    Condition
    Specified Condition
    MAF
    Shift lever position: Neutral
    A/C: Off
    Engine Speed: 3000 rpm
    Between 4.0 gm/sec. and 8.0 gm/sec.



NG
Go to step 26
OK


15.CHECK VALVE TIMING


    A175434E05
  1. Remove the cylinder head cover.

  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" on the timing chain cover.

  1. Check that the timing marks on the camshaft timing sprocket and camshaft timing gear are facing upward as shown in the illustration. If not, turn the crankshaft 1 revolution (360°), then align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

    Text in Illustration 
    *a
    Timing Mark



OK
Go to step 27

NG
ADJUST VALVE TIMING (Click here)

16.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leaks in intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM (Click here)
OK


17.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 31
OK


18.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Data List twice, when the engine is both cold and warmed up.

    Standard:

    Tester Display
    Condition
    Specified Condition
    Coolant Temp
    Cold engine
    Same as ambient air temperature
    Warm engine
    Between 80 and 100°C (176 and 212°F)



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
OK


19.READ VALUE USING INTELLIGENT TESTER (MAF)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF and Coolant Temp.

  1. Allows the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed 3000 rpm.

    Standard:

    Tester Display
    Condition
    Specified Condition
    MAF
    Shift lever position: Neutral
    A/C: Off
    Engine Speed: 3000 rpm
    Between 4.0 gm/sec. and 8.0 gm/sec.



NG
Go to step 26
OK


20.INSPECT SPARK PLUG
  1. Inspect the spark plug of the misfiring cylinder .



NG
REPLACE SPARK PLUG
OK


21.CHECK FOR SPARKS (SPARK TEST)
  1. Perform a spark test .

    HINT:
    If the result of the spark test is normal, proceed to the next step.


NEXT


22.CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


23.INSPECT FUEL INJECTOR ASSEMBLY (POWER SOURCE)


    A200903E23
  1. Disconnect the fuel injector assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B5-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B7-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B9-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B11-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)



NG
CHECK FUEL INJECTOR ASSEMBLY
OK


24.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
  1. Disconnect the fuel injector assembly connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B5-2 - B84-108 (#10)
    Always
    Below 1 Ω
    B7-2 - B84-107 (#20)
    Always
    Below 1 Ω
    B9-2 - B84-106 (#30)
    Always
    Below 1 Ω
    B11-2 - B84-105 (#40)
    Always
    Below 1 Ω
    B5-2 or B84-108 (#10) - Body ground
    Always
    10 Ω or higher
    B7-2 or B84-107 (#10) - Body ground
    Always
    10 Ω or higher
    B9-2 or B84-106 (#10) - Body ground
    Always
    10 Ω or higher
    B11-2 or B84-105 (#10) - Body ground
    Always
    10 Ω or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


25.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
  1. Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


26.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
  1. Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


27.CHECK WHETHER DTC OUTPUT RECURS (DTC P0300, P0301, P0302, P0303 AND/OR P0304)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0300, P0301, P0302, P0303 and/or P0304 are output
    A
    DTC is not output
    B



B
END
A


28.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B72-3 (VG) - B84-118 (VG)
    Always
    Below 1 Ω
    B72-2 (E2G) - B84-116 (E2G)
    Always
    Below 1 Ω
    B72-3 (VG) or B84-118 (VG) - Body ground
    Always
    10 Ω or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


29.REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter (Click here).

    HINT:
    1. If the results of the inspections performed in steps 14 and 19 indicated no problem, proceed to the next step without replacing the mass air flow meter.


NEXT


30.CHECK WHETHER DTC OUTPUT RECURS (DTC P0300, P0301, P0302, P0303 AND/OR P0304)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0300, P0301, P0302, P0303 and/or P0304 are output
    A
    DTC is not output
    B



B
END
A

REPLACE ECM (Click here)  

31.CHECK FUEL LINE
  1. Check the fuel lines for leaks or blockage.



NG
REPAIR OR REPLACE FUEL LINE
OK

REPLACE FUEL PUMP (Click here)