Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Built-in Type Yaw Rate Sensor)

VEHICLE STABILITY CONTROL SYSTEM (for Built-in Type Yaw Rate Sensor) > ABS Warning Light Remains ON

for Preparation Click here


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter via CAN communication.
If any of the following is detected, the ABS warning light remains on:
  1. The skid control ECU (brake actuator assembly) connectors are disconnected from the skid control ECU (brake actuator assembly).
  2. There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.
  3. There is an open in the harness between the combination meter and the skid control ECU (brake actuator assembly).
  4. The ABS control system is defective.

HINT:
In some cases, the intelligent tester cannot be used when the skid control ECU (brake actuator assembly) is abnormal.


WIRING DIAGRAM


C243294E01


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the brake actuator assembly, perform zero point calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


2.CHECK CAN COMMUNICATION SYSTEM
  1. Check if CAN communication system DTCs are output (Click here).

Result 
Result
Proceed to
DTC is not output
A
DTC is output
B


B
CHECK CAN COMMUNICATION SYSTEM (Click here)
A


3.INSPECT BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1NZ-FE)
    B
    NG (for 2NZ-FE)
    C



B
CHECK AND REPLACE CHARGING SYSTEM OR BATTERY (Click here)

C
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY (Click here)
A


4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Turn the ignition switch to ON.



    C243286E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A54-34 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid control ECU)

  1. Turn the ignition switch off.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)


    C243286E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A54-1 (GND1) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid control ECU)

  1. Reconnect the skid control ECU (brake actuator assembly) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)
OK


6.READ VALUE USING INTELLIGENT TESTER (ABS WARNING LIGHT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. According to the display on the tester, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ABS Warning Light
    ABS warning light/OFF or ON
    OFF: Warning light off
    ON: Warning light on
    -

  1. When performing the ABS Warning Light Active Test, check ABS Warning Light in the Data List.


ABS/VSC/TRC 
Tester Display
Test Part
Control Range
Diagnostic Note
ABS Warning Light
ABS warning light
Warning light OFF/ON
Observe combination meter
[Vehicle condition]
Vehicle stopped

Result 
Result
Proceed to
Data List Display
Data List Display when Performing Active Test ON/OFF Operation
ON
Changes between ON and OFF
A
Does not change between ON and OFF
B
OFF
Changes between ON and OFF
A
Does not change between ON and OFF
B


B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A


7.REPLACE COMBINATION METER ASSEMBLY
  1. Turn the ignition switch off.

  1. Replace the combination meter assembly (Click here).


NEXT


8.CHECK COMBINATION METER ASSEMBLY
  1. Connect the intelligent tester to the DLC3.

  1. Perform Active Test of the combination meter assembly using the intelligent tester (Click here).

    OK:
    The ABS warning light turns on or off in accordance with the intelligent tester.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK

CHECK CAN COMMUNICATION SYSTEM (Click here)