Home › Engine / Hybrid System · 2NZ-FE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > Fuel Injector Circuit

for Preparation Click here


DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the intake parts based on signals from the ECM.

WIRING DIAGRAM


A254080E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
  1. Disconnect the fuel injector assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:

    Tester Connection
    Switch Condition
    Specified Condition
    B5-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B7-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B9-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B11-1 - Body ground
    Ignition switch ON
    11 to 14 V



NG
Go to step 4
OK


2.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
  1. Inspect the fuel injector injection and volume (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
  1. Disconnect the fuel injector assembly connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.


Standard Resistance:

Tester Connection
Condition
Specified Condition
B5-2 - B84-108 (#10)
Always
Below 1 Ω
B7-2 - B84-107 (#20)
Always
Below 1 Ω
B9-2 - B84-106 (#30)
Always
Below 1 Ω
B11-2 - B84-105 (#40)
Always
Below 1 Ω
B5-2 or B84-108 (#10) - Body ground
Always
10 kΩ or higher
B7-2 or B84-107 (#20) - Body ground
Always
10 kΩ or higher
B9-2 or B84-106 (#30) - Body ground
Always
10 kΩ or higher
B11-2 or B84-105 (#40) - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

4.CHECK HARNESS AND CONNECTOR (INTEGRATION NO. 1 RELAY (IG2 RELAY) - FUEL INJECTOR ASSEMBLY)
  1. Disconnect the fuel injector assembly connectors.

  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.


Standard Resistance:

Tester Connection
Condition
Specified Condition
B5-1 - 1E-2
Always
Below 1 Ω
B7-1 - 1E-2
Always
Below 1 Ω
B9-1 - 1E-2
Always
Below 1 Ω
B11-1 - 1E-2
Always
Below 1 Ω
B5-1 or 1E-2 - Body ground
Always
10 kΩ or higher
B7-1 or 1E-2 - Body ground
Always
10 kΩ or higher
B9-1 or 1E-2 - Body ground
Always
10 kΩ or higher
B11-1 or 1E-2 - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)