Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

for Preparation Click here


DESCRIPTION

If the front passenger side manual UP / DOWN function does not operate, a malfunction may exist in the power window regulator motor assembly RH or LH (front passenger side), power window regulator switch assembly (front passenger side), power window regulator master switch assembly or wire harness.

WIRING DIAGRAM


B291667E01


B291667E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FRONT PASSENGER SIDE)
  1. Inspect the power window regulator switch assembly (front passenger side) (Click here).



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (FRONT PASSENGER SIDE) (Click here)
OK


2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH OR LH (FRONT PASSENGER SIDE)
  1. Inspect the power window regulator motor assembly RH or LH (front passenger side) (Click here).



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH OR LH (FRONT PASSENGER SIDE) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - P/W RELAY)
B291669E01
B291669E02
  1. for LHD

    1. Disconnect the G2 power window regulator switch assembly (front passenger side) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      G2-3 (B) - Body ground
      Ignition switch ON
      11 to 14 V

      Text in Illustration 
      *A
      for LHD
      *a
      Front view of wire harness connector
      (to Power Window Regulator Switch Assembly (Front Passenger Side))

  1. for RHD

    1. Disconnect the H2 power window regulator switch assembly (front passenger side) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      H2-3 (B) - Body ground
      Ignition switch ON
      11 to 14 V

      Text in Illustration 
      *A
      for RHD
      *a
      Front view of wire harness connector
      (to Power Window Regulator Switch Assembly (Front Passenger Side))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY)
  1. for LHD

    1. Disconnect the G2 power window regulator switch assembly (front passenger side) connector.

    2. Disconnect the G4 power window regulator motor assembly RH (front passenger side) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      G2-4 (U) - G4-2 (U)
      Always
      Below 1 Ω
      G2-1 (D) - G4-1 (D)
      Always
      Below 1 Ω
      G2-4 (U) - Body ground
      Always
      10 kΩ or higher
      G2-1 (D) - Body ground
      Always
      10 kΩ or higher

  1. for RHD

    1. Disconnect the H2 power window regulator switch assembly (front passenger side) connector.

    2. Disconnect the H4 power window regulator motor assembly LH (front passenger side) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      H2-4 (U) - H4-2 (U)
      Always
      Below 1 Ω
      H2-1 (D) - H4-1 (D)
      Always
      Below 1 Ω
      H2-4 (U) - Body ground
      Always
      10 kΩ or higher
      H2-1 (D) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)
  1. for LHD

    1. Disconnect the G2 power window regulator switch assembly (front passenger side) connector.

    2. Disconnect the H1 power window regulator master switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      w/ Rear Power Window 
      Tester Connection
      Condition
      Specified Condition
      G2-5 (SU) - H1-16 (U)
      Always
      Below 1 Ω
      G2-2 (SD) - H1-15 (D)
      Always
      Below 1 Ω
      G2-5 (SU) - Body ground
      Always
      10 kΩ or higher
      G2-2 (SD) - Body ground
      Always
      10 kΩ or higher
      w/o Rear Power Window 
      Tester Connection
      Condition
      Specified Condition
      G2-5 (SU) - H1-12 (U)
      Always
      Below 1 Ω
      G2-2 (SD) - H1-16 (D)
      Always
      Below 1 Ω
      G2-5 (SU) - Body ground
      Always
      10 kΩ or higher
      G2-2 (SD) - Body ground
      Always
      10 kΩ or higher

  1. for RHD

    1. Disconnect the H2 power window regulator switch assembly (front passenger side) connector.

    2. Disconnect the G1 power window regulator master switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      w/ Rear Power Window 
      Tester Connection
      Condition
      Specified Condition
      H2-5 (SU) - G1-12 (U)
      Always
      Below 1 Ω
      H2-2 (SD) - G1-13 (D)
      Always
      Below 1 Ω
      H2-5 (SU) - Body ground
      Always
      10 kΩ or higher
      H2-2 (SD) - Body ground
      Always
      10 kΩ or higher
      w/o Rear Power Window 
      Tester Connection
      Condition
      Specified Condition
      H2-5 (SU) - G1-12 (U)
      Always
      Below 1 Ω
      H2-2 (SD) - G1-10 (D)
      Always
      Below 1 Ω
      H2-5 (SU) - Body ground
      Always
      10 kΩ or higher
      H2-2 (SD) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)