Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > All Doors LOCK/UNLOCK Functions do not Operate Via Master Switch, Driver Side Door Key Cylinder

for Preparation Click here


DESCRIPTION

The main body ECU receives switch signals from the door control switch, and driver side door key cylinder switch, activates the door lock motor on each door accordingly.

WIRING DIAGRAM


B284766E02


B289265E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK DOOR LOCK OPERATION
  1. Proceed to the next step according to the symptom listed in the table below.
    Result 
    Result
    Proceed to
    Doors cannot be locked through master switch
    A
    Doors cannot be locked through driver side door key cylinder
    B



B
Go to step 5
A


2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK SW-LOCK AND DOOR LOCK SW-UNLOCK)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. According to the display on the intelligent tester, read the Data List.


Main Body 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Door Lock SW-Lock
Door manual lock switch signal / OFF or ON
OFF: Door control switch (for front driver door side) is turned to unlock position
ON: Door control switch (for front driver door side) is turned to lock position
-
Door Lock SW-Unlock
Door manual unlock switch signal / OFF or ON
OFF: Door control switch (for front driver door side) is turned to lock position
ON: Door control switch (for front driver door side) is turned to unlock position
-

OK:
When the switch is operating, the intelligent tester should display as shown in the table.



NG
Go to step 3
OK

REPLACE MAIN BODY ECU (Click here)  

3.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
  1. Inspect the power window regulator master switch assembly (Click here).



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH - MAIN BODY ECU AND BODY GROUND)
  1. for LHD:

    1. Disconnect the F76 main body ECU connector.

    2. Disconnect the H1*1 or H13*2 power window regulator master switch assembly (door control switch) connector.

      1. *1: w/ Power Window
      2. *2: w/o Power Window

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      w/ Rear Power Window 
      Tester Connection
      Condition
      Specified Condition
      H1-2 (L) - F76-9 (L1)
      Always
      Below 1 Ω
      H1-9 (UL) - F76-10 (UL1)
      Always
      Below 1 Ω
      H1-1 (GND) - Body ground
      Always
      Below 1 Ω
      H1-2 (L) or F76-9 (L1) - Body ground
      Always
      10 kΩ or higher
      H1-9 (UL) or F76-10 (UL1) - Body ground
      Always
      10 kΩ or higher
      w/o Rear Power Window 
      Tester Connection
      Condition
      Specified Condition
      H1-3 (L) - F76-9 (L1)
      Always
      Below 1 Ω
      H1-9 (UL) - F76-10 (UL1)
      Always
      Below 1 Ω
      H1-7 (GND) - Body ground
      Always
      Below 1 Ω
      H1-3 (L) or F76-9 (L1) - Body ground
      Always
      10 kΩ or higher
      H1-9 (UL) or F76-10 (UL1) - Body ground
      Always
      10 kΩ or higher
      w/o Power Window 
      Tester Connection
      Condition
      Specified Condition
      H13-4 (L) - F76-9 (L1)
      Always
      Below 1 Ω
      H13-2 (UL) - F76-10 (UL1)
      Always
      Below 1 Ω
      H13-3 (GND) - Body ground
      Always
      Below 1 Ω
      H13-4 (L) or F76-9 (L1) - Body ground
      Always
      10 kΩ or higher
      H13-2 (UL) or F76-10 (UL1) - Body ground
      Always
      10 kΩ or higher

  1. for RHD:

    1. Disconnect the F76 main body ECU connector.

    2. Disconnect the G1 power window regulator master switch assembly (door control switch) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      w/ Rear Power Window 
      Tester Connection
      Condition
      Specified Condition
      G1-2 (L) - F76-9 (L1)
      Always
      Below 1 Ω
      G1-8 (UL) - F76-10 (UL1)
      Always
      Below 1 Ω
      G1-9 (GND) - Body ground
      Always
      Below 1 Ω
      G1-2 (L) or F76-9 (L1) - Body ground
      Always
      10 kΩ or higher
      G1-8 (UL) or F76-10 (UL1) - Body ground
      Always
      10 kΩ or higher
      w/o Rear Power Window 
      Tester Connection
      Condition
      Specified Condition
      G1-1 (L) - F76-9 (L1)
      Always
      Below 1 Ω
      G1-3 (UL) - F76-10 (UL1)
      Always
      Below 1 Ω
      G1-7 (GND) - Body ground
      Always
      Below 1 Ω
      G1-1 (L) or F76-9 (L1) - Body ground
      Always
      10 kΩ or higher
      G1-3 (UL) - F76-10 (UL1)
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (Click here)  

5.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK AND UNLOCK SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. According to the display on the intelligent tester, read the Data List.


Main Body 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Door Key SW-Lock
Door lock and unlock switch signal / OFF or ON
OFF: Driver side door key cylinder not turned
ON: Driver side door key cylinder turned to lock position
-
Door Key SW-Unlock
Door lock and unlock switch signal / OFF or ON
OFF: Driver side door key cylinder not turned
ON: Driver side door key cylinder turned to unlock position
-

OK:
ON (driver side door key cylinder is turned to lock/unlock position) appears on the tester screen.



NG
Go to step 6
OK

REPLACE MAIN BODY ECU (Click here)  

6.INSPECT FRONT DOOR LOCK ASSEMBLY (for DRIVER SIDE DOOR)
  1. Inspect the front door lock assembly (Click here).



NG
REPLACE FRONT DOOR LOCK ASSEMBLY (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT DOOR LOCK AND BODY GROUND)
  1. for LHD:

    1. Disconnect the F76 main body ECU.

    2. Disconnect the H5 front door lock assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      H5-9 (L) - F76-11 (L2)
      Always
      Below 1 Ω
      H5-10 (UL) - F76-12 (UL2)
      Always
      Below 1 Ω
      H5-7 (E) - Body ground
      Always
      Below 1 Ω
      H5-9 (L) or F76-11 (L2) - Body ground
      Always
      10 kΩ or higher
      H5-10 (UL) or F76-12 (UL2) - Body ground
      Always
      10 kΩ or higher

  1. for RHD:

    1. Disconnect the F76 main body ECU.

    2. Disconnect the G5 front door lock assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      G5-6 (L) - F76-11 (L2)
      Always
      Below 1 Ω
      G5-5 (UL) - F76-12 (UL2)
      Always
      Below 1 Ω
      G5-8 (E) - Body ground
      Always
      Below 1 Ω
      G5-6 (L) or F76-11 (L2) - Body ground
      Always
      10 kΩ or higher
      G5-5 (UL) or F76-12 (UL2) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (Click here)