Home › Audio/Visual/Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Speaker Circuit

for Preparation Click here


DESCRIPTION

If there is a short in a speaker circuit, the radio receiver assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the radio receiver assembly or speakers.
If a short is detected in a speaker circuit, no sound can be heard from the speakers.

WIRING DIAGRAM


E231978E01


E231979E01


INSPECTION PROCEDURE

1.CONFIRM MODEL
Result 
Result
Proceed to
for 4 Speakers
A
for 6 Speakers
B


B
Go to step 3
A


2.CHECK HARNESS AND CONNECTOR
  1. Disconnect the F107 and F108 radio receiver assembly connectors.

  1. Disconnect the H8 and G8 front No. 1 speaker assembly connectors.

  1. Disconnect the J4*1 and I4*1 or K43*2 and K44*2 rear speaker assembly connectors.

    1. *1: for 5 Door
    2. *2: for 3 Door

  1. Measure the resistance between each of the radio receiver assembly and the front No. 1 speaker assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F107-2 (FL+) - H8-1
    Always
    Below 1 Ω
    F107-6 (FL-) - H8-2
    Always
    Below 1 Ω
    F107-1 (FR+) - G8-1
    Always
    Below 1 Ω
    F107-5 (FR-) - G8-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the radio receiver assembly and the rear speaker assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    for 5 Door 
    Tester Connection
    Condition
    Specified Condition
    F108-2 (RL+) - J4-1
    Always
    Below 1 Ω
    F108-6 (RL-) - J4-2
    Always
    Below 1 Ω
    F108-1 (RR+) - I4-1
    Always
    Below 1 Ω
    F108-3 (RR-) - I4-2
    Always
    Below 1 Ω
    for 3 Door 
    Tester Connection
    Condition
    Specified Condition
    F108-2 (RL+) - K43-1
    Always
    Below 1 Ω
    F108-6 (RL-) - K43-2
    Always
    Below 1 Ω
    F108-1 (RR+) - K44-1
    Always
    Below 1 Ω
    F108-3 (RR-) - K44-2
    Always
    Below 1 Ω

  1. Measure the resistance between each speaker assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H8-1 - Body ground
    Always
    10 kΩ or higher
    H8-2 - Body ground
    Always
    10 kΩ or higher
    G8-1 - Body ground
    Always
    10 kΩ or higher
    G8-2 - Body ground
    Always
    10 kΩ or higher
    J4-1 - Body ground*1
    Always
    10 kΩ or higher
    J4-2 - Body ground*1
    Always
    10 kΩ or higher
    I4-1 - Body ground*1
    Always
    10 kΩ or higher
    I4-2 - Body ground*1
    Always
    10 kΩ or higher
    K43-1 - Body ground*2
    Always
    10 kΩ or higher
    K43-2 - Body ground*2
    Always
    10 kΩ or higher
    K44-1 - Body ground*2
    Always
    10 kΩ or higher
    K44-2 - Body ground*2
    Always
    10 kΩ or higher

    1. *1: for 5 Door
    2. *2: for 3 Door
    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 5
A

REPAIR OR REPLACE HARNESS OR CONNECTOR 

3.CHECK HARNESS AND CONNECTOR
  1. Disconnect the F107 and F108 radio receiver assembly connectors.

  1. Disconnect the H8 and G8 front No. 1 speaker assembly connectors.

  1. Disconnect the F92 and F91 front No. 2 speaker assembly connectors.

  1. Disconnect the J4 and I4 rear speaker assembly connectors.

  1. Measure the resistance between each of the radio receiver assembly and the front No. 2 speaker assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F107-2 (FL+) - F92-4 (+)
    Always
    Below 1 Ω
    F107-6 (FL-) - F92-2 (-)
    Always
    Below 1 Ω
    F107-1 (FR+) - F91-4 (+)
    Always
    Below 1 Ω
    F107-5 (FR-) - F91-2 (-)
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 2 speaker assembly and front No. 1 speaker assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F92-3 (TWL+) - H8-1
    Always
    Below 1 Ω
    F92-1 (TWL-) - H8-2
    Always
    Below 1 Ω
    F91-3 (TWR+) - G8-1
    Always
    Below 1 Ω
    F91-1 (TWR-) - G8-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the radio receiver assembly and the rear speaker assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F108-2 (RL+) - J4-1
    Always
    Below 1 Ω
    F108-6 (RL-) - J4-2
    Always
    Below 1 Ω
    F108-1 (RR+) - I4-1
    Always
    Below 1 Ω
    F108-3 (RR-) - I4-2
    Always
    Below 1 Ω

  1. Measure the resistance between each speaker assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H8-1 - Body ground
    Always
    10 kΩ or higher
    H8-2 - Body ground
    Always
    10 kΩ or higher
    G8-1 - Body ground
    Always
    10 kΩ or higher
    G8-2 - Body ground
    Always
    10 kΩ or higher
    F92-4 (+) - Body ground
    Always
    10 kΩ or higher
    F92-2 (-) - Body ground
    Always
    10 kΩ or higher
    F91-4 (+) - Body ground
    Always
    10 kΩ or higher
    F91-2 (-) - Body ground
    Always
    10 kΩ or higher
    J4-1 - Body ground
    Always
    10 kΩ or higher
    J4-2 - Body ground
    Always
    10 kΩ or higher
    I4-1 - Body ground
    Always
    10 kΩ or higher
    I4-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
  1. Check that the malfunction disappears when another speaker in good condition is installed.

    OK:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speakers.
    2. If there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Inspect the front No. 1 speaker assembly (Click here).

    HINT:
    The speaker should not be removed to check resistance.



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


6.INSPECT REAR SPEAKER ASSEMBLY
  1. Inspect the rear speaker assembly.

    1. for 5 Door (Click here)
    2. for 3 Door (Click here)

    HINT:
    The speaker should not be removed to check resistance.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 5 Door)
    B
    NG (for 3 Door)
    C



B
REPLACE REAR SPEAKER ASSEMBLY (Click here)

C
REPLACE REAR SPEAKER ASSEMBLY (Click here)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)