Home › Drivetrain ยท C54 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSAXLE ASSEMBLY

MANUAL TRANSAXLE ASSEMBLY > REMOVAL

for Preparation Click here



1. DRAIN TRANSAXLE OIL
  1. Remove the manual transmission filler plug and the gasket.

  1. Remove the drain plug sub-assembly and gasket, and then drain the manual transaxle oil.

  1. Install a new gasket and the drain plug sub-assembly.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



2. REMOVE FRONT WIPER MOTOR AND LINK
(Click here)


3. REMOVE FRONT NO. 1 VENTILATOR SEAL (for LHD)


C242062
  1. Disengage the clamp and remove the front No. 1 ventilator seal.



4. REMOVE FRONT NO. 1 VENTILATOR SEAL (for RHD)


A249556
  1. Disengage the clamp and remove the front No. 1 ventilator seal.



5. REMOVE FRONT AIR SHUTTER SEAL RH (for LHD)

HINT:
Use the same procedure as for the No. 1 ventilator seal.



6. REMOVE FRONT AIR SHUTTER SEAL RH (for RHD)

HINT:
Use the same procedure as for the No. 1 ventilator seal.



7. REMOVE INNER COWL TOP TO COWL BRACE (for LHD)


C242063
  1. Remove the 2 bolts and the inner cowl top to cowl brace.



8. REMOVE INNER COWL TOP TO COWL BRACE (for RHD)


A249554
  1. Remove the 2 bolts and the inner cowl top to cowl brace.



9. REMOVE OUTER COWL TOP PANEL (for LHD)


C242064
  1. Disengage the 2 clamps and separate the wire harness.



  1. Remove the 8 bolts and the outer cowl top panel.


    C242065



10. REMOVE OUTER COWL TOP PANEL (for RHD)


A249552
  1. Disengage the 2 clamps and separate the wire harness.



  1. Remove the 8 bolts and the outer cowl top panel.


    A249553



11. REMOVE AIR CLEANER ASSEMBLY


    A249575
  1. Disengage the clamp and disconnect the fuel vapor feed hose assembly from the No. 1 air cleaner hose.

  1. Loosen the 2 hose clamps and disconnect the fuel vapor feed hose assembly from the No. 1 air cleaner hose and vacuum switching valve assembly.



    A249576
  1. Disconnect the No. 2 fuel vapor feed hose from the intake manifold.



    A249577
  1. Disengage the 2 clamps and disconnect the wire harness from the air cleaner cap sub-assembly and vacuum switching valve assembly.

  1. Disconnect the mass air flow meter connector.

  1. Disconnect the vacuum switching valve connector.



    A249578
  1. Loosen the hose clamp and disconnect the No. 1 air cleaner hose from the throttle with motor body assembly.

  1. Disengage the 2 clamps and remove the air cleaner cap sub-assembly with No. 1 air cleaner hose.



    A246503
  1. Remove the air cleaner element.



    A249653
  1. Disengage the clamp and disconnect the wire harness from the air cleaner case.

  1. Remove the 2 bolts and the air cleaner case from the air cleaner bracket.



12. REMOVE AIR CLEANER BRACKET


A248643
  1. Disengage the clamp and disconnect the wire harness from the air cleaner bracket.

  1. Remove the 2 bolts and the air cleaner bracket.



13. REMOVE BATTERY


A248909
  1. Disconnect the cable from the battery terminal.

  1. Loosen the 2 nuts and remove the battery clamp.

  1. Remove the battery.



14. REMOVE BATTERY TRAY


15. REMOVE BATTERY CARRIER (for LHD)


A259809
  1. Disengage the 6 wire harness clamps and separate the wire harness from the battery carrier.

  1. Remove the 5 bolts and the battery carrier.



16. REMOVE BATTERY CARRIER (for RHD)


A247997
  1. Disengage the 7 wire harness clamps and separate the wire harness from the battery carrier.

  1. Remove the 5 bolts and the battery carrier.



17. REMOVE STARTER ASSEMBLY (for 1NZ-FE)
(Click here)


18. REMOVE STARTER ASSEMBLY (for 2NZ-FE)
(Click here)


19. SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY


C106371
  1. Remove the 4 bolts, then separate the clutch release cylinder assembly.

    HINT:
    Suspend the clutch release cylinder assembly with a piece of rope so as not to overload the clutch pipe.



20. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY


    C235168E01
  1. Remove the clip A and washer, and separate the control shift cable from the manual transaxle assembly.
    Text in Illustration 
    *1
    Control Shift Cable
    *2
    Control Select Cable
    *3
    Clip A
    *4
    Clip B

  1. Remove the clip B from the control shift cable, and separate the control shift cable from the control cable bracket.

  1. Remove the clip A and washer, and separate the control select cable from the manual transaxle assembly.

  1. Remove the clip B from the control select cable, and separate the control select cable from the control cable bracket.



21. REMOVE CONTROL CABLE BRACKET


C106374
  1. Remove the 2 bolts and the control cable bracket.



22. DISCONNECT WIRE HARNESS (w/ ABS)


    C244618
  1. Separate the 4 clamps and remove the bolt, and separate the wire harness from the manual transaxle assembly.



    C108079
  1. Remove the bolt and separate the ground wire.

  1. Disconnect the back up light switch connector.



23. DISCONNECT WIRE HARNESS (w/o ABS)


    C244618
  1. Separate the 4 clamps and remove the bolt, and separate the wire harness from the manual transaxle assembly.



    C108079
  1. Remove the bolt and separate the ground wire.

  1. Disconnect the back up light switch connector.

  1. Disconnect the speedometer sensor connector.



24. REMOVE FRONT DRIVE SHAFT ASSEMBLIES
(Click here)


25. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
(Click here)


26. SUPPORT ENGINE AND TRANSAXLE


    C244599
  1. On a flat location, set the attachment, plate lift attachment, and wooden block in the positions shown in the figure, and set the engine assembly.
    Text in Illustration 
    V100155
    Attachment Placement Positions

    NOTICE:
    1. Set the engine assembly with transaxle so that it is horizontal.
    2. Never attach the attachment and plate lift attachment to the oil pan section of the engine assembly.



27. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING CONTROL BRACKET


C116856
  1. Remove the 4 bolts and the transverse engine engine mounting control bracket.



28. SUPPORT MANUAL TRANSAXLE ASSEMBLY
  1. Support the manual transaxle assembly with a transmission jack so that it is stable.



29. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR


C106372
  1. Remove the bolt and nut, then separate the transverse engine engine mounting insulator from the transverse engine engine mounting bracket.

    HINT:
    Hold the nut and loosen the bolt.

  1. Remove the 5 bolts and the transverse engine engine mounting insulator.



30. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET


C121108
  1. Remove the 4 bolts and the transverse engine engine mounting bracket from the manual transaxle assembly.



31. REMOVE MANUAL TRANSAXLE ASSEMBLY


    C063143
  1. Remove the 7 bolts and the manual transaxle assembly.

    NOTICE:
    1. To prevent damage to the knock pins, do not pry between the transaxle and engine.
    2. To avoid damage to the input shaft, do not forcefully shake the manual transaxle.



32. REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY (w/ ABS)
  1. Remove the bolt and the speedometer driven hole cover sub-assembly from the manual transaxle assembly.

  1. Remove the O-ring from the speedometer driven hole cover sub-assembly.



33. REMOVE SPEEDOMETER SENSOR (w/o ABS)
  1. Remove the bolt and the speedometer sensor from the manual transaxle assembly.



    C117097E05
  1. Remove the E-ring and the speedometer driven gear from the speedometer sensor.
    Text in Illustration 
    *1
    Speedometer Driven Gear
    *2
    O-ring
    *3
    E-ring

  1. Remove the O-ring from the speedometer sensor.



34. REMOVE WIRE HARNESS CLAMP BRACKET


    C244604
  1. Remove the 3 bolts and the 3 wire harness clamp brackets from the manual transaxle assembly.