Home › Engine / Hybrid System ยท 1NZ-FE › ENGINE MECHANICAL › CYLINDER HEAD GASKET

CYLINDER HEAD GASKET > INSTALLATION

for Preparation Click here



1. INSPECT CYLINDER HEAD SET BOLT


A098332E03
  1. Using a vernier caliper, measure the length of the cylinder head set bolt from the seat to the end.
    Text in Illustration 
    *a
    Measurement Length

    Standard length:
    142.8 to 144.2 mm (5.6220 to 5.6772 in.)

    Maximum length:
    147.1 mm (5.7913 in.)

    If the bolt length is greater than the maximum, replace the cylinder head set bolt.



2. INSTALL CYLINDER HEAD GASKET


A117469E02
  1. Place a new cylinder head gasket on the cylinder block with the Lot No. stamp facing upward.
    Text in Illustration 
    *a
    Lot No.

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Check the mounting orientation of the cylinder head gasket.
    3. Place the cylinder head on the cylinder head gently in order not to damage the gasket.



3. INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
The cylinder head bolts are tightened in 2 successive steps.

  1. Apply a light coat of engine oil to the threads of the cylinder head bolts.



    A035288
  1. Using several steps, install and tighten the 10 cylinder head bolts and plate washers uniformly with an 8 mm bi-hexagon wrench, in the sequence shown in the illustration.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

  1. Mark the front of the cylinder head bolt with paint.



    A116959E04
  1. Retighten the cylinder head bolts 90° and then an additional by 90° as shown in the illustration.
    Text in Illustration 
    *a
    Paint Mark

  1. Check that the paint mark is now at a 180° angle from the front.



    A073748E06
  1. Apply a continuous bead of seal packing (Diameter 4.5 to 5.5 mm (0.177 to 0.217 in.) as shown in the illustration.

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

    Text in Illustration 
    *1
    Cylinder Head
    *2
    Cylinder Head Gasket
    *3
    Cylinder Block
    *a
    Seal Packing
    *b
    Diameter: 4.5 to 5.5 mm

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the oil pump assembly within 3 minutes and tighten the bolts within 15 minutes of applying the seal packing.



4. INSTALL CAMSHAFT


A117473
  1. Examine the front marks and numbers and check that the sequence is as shown in the illustration. Then provisionally tighten the 19 bolts.



    A117472E05
  1. Uniformly tighten the bolts in several steps in the sequence shown in the illustration and install No. 1 camshaft bearing cap and No. 2 camshaft bearing cap.
    Text in Illustration 
    *1
    No. 1 Bearing Cap
    *2
    No. 2 Bearing Cap

    Torque:
    No. 1 Camshaft bearing cap:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }
    No. 2 Camshaft bearing cap:
    13 N*m{ 129 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Tighten each bolt uniformly while keeping the camshaft level.



5. INSTALL CHAIN SUB-ASSEMBLY


A116571E06
  1. Make sure that all the timing marks are in the positions (TDC) shown in the illustration.
    Text in Illustration 
    *a
    Timing Marks
    *b
    Timing Mark

    HINT:
    The positions of the timing marks may differ the predetermined positions due to the force of the valve spring.



    A116573E04
  1. Set the timing mark of the crankshaft in a position between 40 and 140° ATDC, as illustrated.
    Text in Illustration 
    *a
    Timing Mark
    *b
    40° to 140° ATDC



    A116574E07
  1. Set the camshaft timing gear and the camshaft timing sprocket in the positions (20° ATDC) shown in the illustration.
    Text in Illustration 
    *a
    20° ATDC
    *b
    Timing Mark
    *c
    Timing Marks

  1. Set the crankshaft in the position (20° ATDC) shown in the illustration.



    A116576
  1. Install the No. 1 chain vibration damper with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



    A116577E04
  1. Align the timing marks of the camshaft with the mark plates of the timing chain and install the timing chain.
    Text in Illustration 
    *a
    Mark Plates
    *b
    Timing Marks
    *c
    Mark Plate
    *d
    Timing Mark

    HINT:
    Align the timing marks with the mark plates while turning the hexagonal service portion of the camshaft using a wrench.



6. INSTALL CHAIN TENSIONER SLIPPER


A116569
  1. Install the chain tensioner slipper.



7. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY


A116568
  1. Install the No. 1 chain tensioner assembly with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Remove the bar from the No. 1 chain tensioner assembly.



8. INSTALL OIL PUMP SEAL


A166953E05
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover.
    Text in Illustration 
    *1
    Splinter of Wood

    SST
    09950-60010   (09951-00250, 09951-00410, 09952-06010)
    09950-70010   (09951-07100)

    NOTICE:
    Do not tap the oil seal at an angle.

  1. Apply a light coat of MP grease to the oil pump seal lip.

    NOTICE:
    Keep the lip free of foreign matter.



9. INSTALL OIL PUMP ASSEMBLY


A116556
  1. Install 2 new O-rings onto the 2 locations as shown in the illustration.



  1. Apply seal packing to the oil pump assembly, cylinder head and cylinder block as shown in the illustration.


    A264211E01


    Text in Illustration 
    *a
    Seal Packing
    *b
    Seal Width (Other Part)
    *c
    Seal Width (Water Pump Part)
    -
    -

    Seal packing:
    Water pump part Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent
    Other part Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the oil pump assembly within 3 minutes and tighten the bolts and nut within 15 minutes of applying seal packing.
    3. Do not expose the seal to engine oil for at least 2 hours after the installation.



    A116558
  1. Align the keyway of the oil pump rotor with the rectangular portion of the crankshaft, and slide the oil pump into place.



    A116554E01
  1. Install the oil pump assembly with the 15 bolts and the nut. Tighten the bolts and nut uniformly in several steps.

    Torque:
    bolt A:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }
    bolt B:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }
    bolt C:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }
    nut D:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }
    bolt E:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    NOTICE:
    After installing the oil pump assembly, install the mounting bracket and water pump within 15 minutes.

    HINT:
    Each bolt length is as follows.
    A: 30 mm (1.181 in.)
    B: 35 mm (1.378 in.)
    C: 20 mm (0.787 in.)
    E: 14 to 20 mm (0.551 to 0.787 in.), Double ended bolt



10. INSTALL ENGINE WATER PUMP ASSEMBLY


A116192
  1. Install the engine water pump and a new gasket with the 3 bolts and 2 nuts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }



11. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET


A080957E01
  1. Install the transverse engine engine mounting bracket with the 4 bolts.

    Torque:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }



12. INSTALL WATER PUMP PULLEY


A116191E01
  1. Using SST, install the water pump pulley with the 3 bolts.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

    SST
    09960-10010   (09962-01000, 09963-00700)



13. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Apply a light coat of engine oil to a new O-ring and install it onto the camshaft timing oil control valve assembly.

    HINT:
    Do not twist the O-ring.

  1. Apply a light coat of engine oil to the O-ring and install the camshaft timing oil control valve assembly with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the camshaft timing oil control valve assembly connector.



14. INSTALL CRANKSHAFT POSITION SENSOR
  1. Apply a light coat of engine oil to the O-ring.

    NOTICE:
    If reusing the camshaft position sensor, be sure to inspect the O-ring.

  1. Install the crankshaft position sensor with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    NOTICE:
    1. Do not twist the O-ring.
    2. If a component has been dropped or subjected to a strong impact, replace it.

  1. Connect the crankshaft position sensor connector.



15. INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY
  1. Align the pin hole of the crankshaft damper with the pin and install the crankshaft damper sub-assembly.

  1. Provisionally install the bolt.

  1. Using 2 SST, tighten the bolt while holding the crankshaft damper sub-assembly.

    SST
    09213-14010   (91651-60865)
    09330-00021  

    Torque:
    128 N*m{ 1305 kgf*cm , 95 ft.*lbf }

    NOTICE:
    Check the SST installation positions when installing them, to avoid the SST fixing bolts from coming into contact with the oil pump assembly.



16. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
  1. Install the engine mounting insulator sub-assembly RH with the 4 bolts and 2 nuts.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }



17. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


A260538
Text in Illustration 
V100155
Seal Packing
  1. Apply seal packing to the cylinder head as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after the installation.



    A035756E04
  1. Install the cylinder head cover sub-assembly with the 9 bolts, 2 nuts and 2 seal washers.

  1. Tighten the 9 bolts and 2 nuts in the sequence shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. for LHD:

    1. Connect the connector and 4 wire harness clamps and connect the engine wire harness.

    2. Install the wire harness bracket with the bolt.

      Torque:
      13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. for RHD:

    1. Connect the connector and 3 wire harness clamps and connect the engine wire harness.

  1. Connect the 4 fuel injector connectors.



18. INSTALL NO. 1 IGNITION COIL


  1. Install the 4 No. 1 ignition coils with the 4 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


    NOTICE:
    A268161E01
    If the body or cap of the ignition coil is dropped or subjected to a strong impact, replace the ignition coil with a new one.

    Text in Illustration 
    *1
    Body
    *2
    Cap

  1. Connect the 4 No. 1 ignition coil connectors.



19. INSTALL FUEL VAPOR FEED HOSE ASSEMBLY
  1. Connect fuel vapor feed hose assembly.



20. INSTALL VENTILATION HOSE
  1. Connect the ventilation hose.



21. INSTALL GENERATOR ASSEMBLY
(Click here)


22. INSTALL MANIFOLD SUPPORT BRACKET
  1. Install the manifold support bracket with the 3 bolts.

    Torque:
    44 N*m{ 449 kgf*cm , 33 ft.*lbf }



23. INSTALL EXHAUST PIPE GASKET


    A128852E04
  1. Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.
    Text in Illustration 
    *1
    Exhaust pipe gasket
    *2
    Wooden Block
    *3
    Plastic Hammer
    *4
    Exhaust Manifold

    NOTICE:
    1. Install the gasket in the correct direction.
    2. Do not reuse the gasket.
    3. Do not damage the gasket by dropping it, etc.
    4. Do not damage the outer surface of the gasket.
    5. Do not push in the gasket with the exhaust pipe when connecting it.



24. INSTALL NO. 2 EXHAUST PIPE GASKET


A128852E04
  1. Using a plastic hammer and a wooden block, tap in a new No. 2 exhaust pipe gasket until its surface is flush with the front exhaust pipe assembly.
    Text in Illustration 
    *1
    No. 2 Exhaust Pipe Gasket
    *2
    Wooden Block
    *3
    Plastic Hammer
    *4
    Front Exhaust Pipe Assembly

    NOTICE:
    1. Install the gasket in the correct direction.
    1. Do not reuse the gasket.
    1. Do not damage the gasket by dropping it, etc.
    1. Do not damage the outer surface of the gasket.
    1. Do not push in the gasket with the exhaust pipe when connecting it.



25. INSTALL FRONT EXHAUST PIPE ASSEMBLY


A104634
  1. Using a vernier caliper, measure the free length of the compression spring.

    Minimum length:
    40.5 mm (1.594 in.)

    If the length is not as specified, replace the compression spring.



    A247549E01
  1. Install the front exhaust pipe assembly onto the exhaust manifold with the 2 compression springs and 2 bolts.
    Text in Illustration 
    *1
    Exhaust Manifold
    *2
    Front Exhaust Pipe Assembly
    *3
    Exhaust Pipe Gasket
    *a
    Space between flanges: 8.5 mm (0.335 in.)

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

    HINT:
    After the installation, check that the gaps between the flanges of the exhaust manifold and front exhaust pipe assembly are consistent front-to-rear and left-to-right.



26. CONNECT WIRE HARNESS
  1. Connect the wire harness with the 2 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



27. INSTALL NO. 1 WATER BY-PASS PIPE
  1. Install No. 1 water by-pass pipe with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



28. CONNECT INLET HEATER WATER HOSE A
  1. Connect inlet heater water hose A.



29. CONNECT HEATED OXYGEN SENSOR CONNECTOR
  1. Connect the heated oxygen sensor connector.

  1. Install the sensor bracket with the bolt.



30. CONNECT ENGINE COOLANT TEMPERATURE SENSOR CONNECTOR
  1. Connect the engine coolant temperature sensor connector.



31. CONNECT CAMSHAFT POSITION SENSOR CONNECTOR
  1. Connect the camshaft position sensor connector.



32. CONNECT BOOSTER VACUUM TUBE
  1. Connect the booster vacuum tube.



33. CONNECT FUEL TUBE SUB-ASSEMBLY


A154755
Text in Illustration 
V100135
Push
  1. Insert the fuel tube connector into the fuel delivery pipe until a click sound can be heard.

    NOTICE:
    1. Check that there are no scratches or foreign matter around the disconnected parts of the fuel tube connector and pipe before performing this work.
    2. After connecting the fuel tube, check that the fuel tube connector and pipe are securely connected by pulling them.

  1. Install the EFI fuel pipe clamp.



34. INSTALL OIL LEVEL DIPSTICK GUIDE
  1. Apply engine oil to a new O-ring.

  1. Install the O-ring onto the oil level dipstick guide.

  1. Install the oil level dipstick guide with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Engage the clamp and connect the wire harness to the oil level dipstick guide.



35. INSTALL INTAKE MANIFOLD
  1. Install a new gasket onto the intake manifold.

  1. Install the intake manifold with the 3 bolts and 2 nuts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

  1. Connect the 3 wire harness clamps shown in the illustration.



36. INSTALL OIL LEVEL DIPSTICK SUB-ASSEMBLY


37. CONNECT UNION TO CONNECTOR TUBE HOSE
  1. Connect the union to connector tube hose.



38. CONNECT VENTILATION HOSE
  1. Connect the ventilation hose.



39. CONNECT THROTTLE WITH MOTOR BODY CONNECTOR
  1. Install the throttle with motor body connector bracket with the nut.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the throttle with motor body connector.

  1. Connect the wire harness clamp.



40. CONNECT WATER BY-PASS HOSE
  1. Connect the water by-pass hose.



41. CONNECT NO. 2 WATER BY-PASS HOSE
  1. Connect No. 2 water by-pass hose.



42. INSTALL WATER FILLER SUB-ASSEMBLY
  1. Install the water filler sub-assembly with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect No. 1 radiator hose to the cylinder head.



43. CONNECT RESERVE TANK HOSE
  1. Connect the reserve tank hose.



44. CONNECT NO. 3 RADIATOR HOSE
  1. Connect No. 3 radiator hose.



45. INSTALL NO. 1 IGNITION COIL
(Click here)


46. INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE
  1. Install the air cleaner cap sub-assembly with No. 1 air cleaner hose to the throttle body assembly with the 2 clamps.

  1. Tighten the hose clamp.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }

  1. Engage the wire harness clamp and install the wire harness to the vacuum switching valve assembly.

  1. Connect the vacuum switching valve assembly connector.

  1. Connect the mass air flow meter connector.

  1. Engage the 2 clamps and connect the wire harness to the air cleaner cap sub-assembly and vacuum switching valve assembly.

  1. Connect the No. 2 fuel vapor feed hose to the intake manifold.

  1. Install the fuel vapor feed hose to the No. 1 air cleaner hose.

  1. Connect the fuel vapor feed hose assembly to the vacuum switching valve assembly and No. 1 air cleaner hose.



47. INSTALL BATTERY TRAY


48. INSTALL BATTERY


49. INSTALL OUTER COWL TOP PANEL (for LHD)
  1. Install the outer cowl top panel with the 8 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Engage the 2 clamps and install the wire harness.



50. INSTALL OUTER COWL TOP PANEL (for RHD)
  1. Install the outer cowl top panel with the 8 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Engage the 2 clamps and install the wire harness.



51. INSTALL INNER COWL TOP TO COWL BRACE (for LHD)
  1. Install the cowl top to cowl brace with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



52. INSTALL INNER COWL TOP TO COWL BRACE (for RHD)
  1. Install the cowl top to cowl brace with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



53. INSTALL FRONT NO. 1 VENTILATOR SEAL (for LHD)
  1. Engage the clip and install the front No. 1 ventilator seal.



54. INSTALL FRONT NO. 1 VENTILATOR SEAL (for RHD)
  1. Engage the clip and install the front No. 1 ventilator seal.



55. INSTALL FRONT AIR SHUTTER SEAL RH (for LHD)

HINT:
Use the same procedure for the RH and LH sides.



56. INSTALL FRONT AIR SHUTTER SEAL RH (for RHD)

HINT:
Use the same procedure as for the front No. 1 ventilator seal.



57. INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY
(Click here)


58. INSTALL FRONT WHEEL RH

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



59. ADD ENGINE COOLANT
  1. Tighten the cylinder block drain cock plug and the radiator drain cock plug.

    Torque:
    13 N*m{ 133 kgf*cm , 9.6 ft.*lbf }

  1. Pour engine coolant into the radiator assembly until it is full.

    Standard capacity:
    5.0 liters (5.3 US qts, 4.4 Imp. qts)

    NOTICE:
    Do not substitute water for coolant.

    HINT:
    1. Use of improper engine coolant may damage the engine coolant system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Check the coolant level inside the radiator assembly by squeezing the No. 2 radiator hose and the No. 3 radiator hose several times by hand. If the coolant level goes down, add engine coolant.

  1. Install the water filler cap sub-assembly securely.

  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens.
      While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by pressing the No. 2 radiator hose by hand, and checking when the coolant starts to flow inside the hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Press the No. 2 radiator hose and No. 3 radiator hose several times by hand to bleed air.

      CAUTION:
      When pressing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

  1. Stop the engine and wait until the coolant cools down.

  1. If the coolant level is below the full level, perform steps (b) through (g) again and repeat the operation until the coolant level stays at the full level.

  1. Recheck the coolant level inside the radiator reservoir tank assembly. If it is below the full level, add coolant.



60. ADD ENGINE OIL
  1. Add fresh engine oil.

    Standard Oil Grade:

    Oil Grade
    Oil Viscosity (SAE)
    API grade SL "energy-conserving", API grade SM "energy-conserving" or ILSAC multigrade engine oil
    1. 5W-30
    1. 10W-30
    API grade SL or SM multigrade engine oil
    1. 15W-40
    1. 20W-50


    Oil capacity:

    Item
    Capacity
    Drain and refill with oil filter change
    3.7 liters (3.9 US qts, 3.3 Imp. qts)
    Drain and refill without oil filter change
    3.4 liters (3.6 US qts, 3.0 Imp. qts)
    Dry fill
    4.1 liters (4.3 US qts, 3.6 Imp. qts)



61. INSPECT FOR ENGINE COOLANT LEAK

CAUTION:
To avoid the danger of being burned, do not remove the water filler cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.



    A250661E01
  1. Fill the radiator assembly with engine coolant, then attach a radiator cap tester.
    Text in Illustration 
    *1
    Radiator Cap Tester

  1. Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.



62. INSPECT ENGINE OIL LEVEL
  1. Warm up and stop the engine, and then wait for 5 minutes.

  1. Check that the engine oil level is between the low level and full level marks on the engine oil level dipstick.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill with engine oil above the full level mark.



63. INSPECT FOR ENGINE OIL LEAK


64. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the intelligent tester main switch on.

      NOTICE:
      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump /Speed.

    4. Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.

  1. Inspect for fuel leaks.

    1. Check for fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts if necessary.

  1. Turn the ignition switch off.

  1. Disconnect the intelligent tester from the DLC3.



65. INSPECT FOR EXHAUST GAS LEAK


66. INSPECT IGNITION TIMING
  1. When using an intelligent tester:

    1. Warm up and stop the engine.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON and turn the tester on.

    4. Start the engine.

    5. Select the following menu items:
      Powertrain / Engine and ECT / Active Test / TC and TE1 / ON.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    6. Inspect the ignition timing during idling.

      Standard ignition timing:
      Transaxle
      Ignition Timing
      Manual Transaxle
      8 to 12 degrees BTDC
      Automatic Transaxle

      NOTICE:
      1. Turn all the electrical systems and the A/C off.
      2. Inspect the ignition timing with the cooling fan off.
      3. When checking the ignition timing, shift the transaxle to the neutral position.

    7. Select the following menu items: TC and TE1 / OFF.

    8. Turn the ignition switch off.

    9. Disconnect the intelligent tester from the DLC3.



  1. When not using an intelligent tester:

    1. Remove the No. 2 cylinder head cover .



    2. A116196
    3. Pull out the wire harness (brown) shown in the illustration.

      NOTICE:
      After checking, wrap the wire harness with tape.

    4. Warm up and stop the engine.

    5. Connect the clip of the timing light to the wire harness.

      NOTICE:
      Use a timing light that detects the first signal.



    6. A169891E06
    7. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
      Text in Illustration 
      *a
      Front view of DLC3

      SST
      09843-18040  

      NOTICE:
      Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.

    8. Start the engine.

    9. Inspect the ignition timing during idling.

      Standard ignition timing:
      Transaxle
      Ignition Timing
      Manual Transaxle
      8 to 12 degrees BTDC
      Automatic Transaxle

      NOTICE:
      1. Turn all the electrical systems and the A/C off.
      2. Inspect the ignition timing with the cooling fan off.
      3. When checking the ignition timing, shift the transaxle to the neutral position.

    10. Turn the ignition switch off.

    11. Remove the timing light.

    12. Install the No. 2 cylinder head cover .

    13. Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.



67. INSPECT ENGINE IDLING SPEED
  1. When using an intelligent tester:

    1. Warm up and stop the engine.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON and turn the tester on.

    4. Start the engine.

    5. Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    6. Inspect the engine idling speed.

      Standard Idling speed:
      Transaxle
      Ignition Timing
      Manual Transaxle
      600 to 700 rpm
      Automatic Transaxle
      650 to 750 rpm

      NOTICE:
      1. Turn all the electrical systems and the A/C off.
      2. Inspect the idling speed with the cooling fan off.
      3. When checking the idling speed, shift the transaxle to the neutral position or the parking position.

    7. Turn the ignition switch off.

    8. Disconnect the intelligent tester from the DLC3.



  1. When not using an intelligent tester.

    1. Warm up and stop the engine.



    2. A169891E06
    3. Install SST to terminal 9 (TAC) of the DLC3, then connect a tachometer.
      Text in Illustration 
      *a
      Front view of DLC3

      SST
      09843-18040  

      NOTICE:
      Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.

    4. Start the engine.

    5. Inspect the engine idling speed.

      Standard Idling speed:
      Transaxle
      Ignition Timing
      Manual Transaxle
      600 to 700 rpm
      Automatic Transaxle
      650 to 750 rpm

      NOTICE:
      1. Turn all the electrical systems and the A/C off.
      1. Inspect the idling speed with the cooling fan off.
      1. When checking the idling speed, shift the transaxle to the neutral position or the parking position.

    6. Turn the ignition switch off.

    7. Disconnect the tachometer.

    8. Remove SST from terminal 9 (TAC).



68. INSPECT COMPRESSION
  1. Warm up and stop the engine.

  1. Remove the No. 2 cylinder head cover .

  1. Remove the 4 ignition coils .

  1. Remove the 4 spark plugs .

  1. Disconnect the 4 fuel injector connectors.



    A116195
  1. Inspect the cylinder compression pressure.

    1. Insert a compression gauge into the spark plug hole.

    2. Fully open the throttle.

    3. While cranking the engine, measure the compression pressure.

      Compression:
      980 kPa (10.0 kgf/cm2, 142 psi)

      Minimum pressure:
      784 kPa (8.0 kgf/cm2, 114 psi)

      Difference between each cylinder:
      98 kPa (1.0 kgf/cm2, 14 psi) or less

      NOTICE:
      1. Use a fully-charged battery so the engine speed can be increased to 250 rpm or more.
      2. Inspect the other cylinders in the same way.
      3. Measure the compression in as short a time as possible.

    4. If the cylinder compression is low, pour a light coat of engine oil into the cylinder through the spark plug hole, then inspect it again.

      HINT:
      1. If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
      2. If the pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.

  1. Connect the 4 fuel injector connectors.

  1. Install the 4 spark plugs .

  1. Install the 4 ignition coils .

  1. Install the No. 2 cylinder head cover .

  1. Clear the DTC (Click here).



69. INSPECT CO/HC
  1. Start the engine.

  1. Run the engine at 2500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe while idling.

  1. Check the CO/HC concentration during idling and when running at 2500 rpm.

    HINT:
    When doing the 2 mode (with the engine idling/running at 2500 rpm) test, the measuring procedures are determined by applicable local regulations.

    If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.

    1. Check the heated oxygen sensor operation (Click here).

    2. See the table below for possible causes, then inspect the applicable parts and repair them if necessary.

      CO
      HC
      Problems
      Possible Causes
      Normal
      High
      Rough idling
      1. Faulty ignition:
        1. Incorrect timing
        2. Fouled, shorted or improperly gapped plugs
      2. Incorrect valve clearance
      3. Leakage from intake and exhaust valves
      4. Leakage from cylinders
      Low
      High
      Rough idling
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idling
      (Black smoke from exhaust)
      1. Restricted air cleaner filter element
      2. Plugged PCV valve
      3. Faulty EFI systems:
        1. Faulty pressure regulator
        2. Faulty engine coolant temperature sensor
        3. Faulty mass air flow meter
        4. Faulty ECM
        5. Faulty injectors
        6. Throttle body



70. INSTALL NO. 2 CYLINDER HEAD COVER
  1. Install the No. 2 cylinder head cover with the 4 nuts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



71. INSTALL ENGINE UNDER COVER LH (for Plastic Type)

Torque:
5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



72. INSTALL ENGINE UNDER COVER RH (for Plastic Type)

Torque:
5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



73. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Metal Type)

Torque:
18 N*m{ 184 kgf*cm , 13 ft.*lbf }