Home › Engine / Hybrid System ยท 1NZ-FE › ENGINE MECHANICAL › CYLINDER HEAD GASKET

CYLINDER HEAD GASKET > REMOVAL

for Preparation Click here


NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


2. REMOVE FRONT WHEEL RH


3. REMOVE ENGINE UNDER COVER RH (for Plastic Type)


4. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Metal Type)


5. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and drain the engine oil.

  1. Clean the drain plug.

  1. Install the drain plug with a new gasket.

    Torque:
    38 N*m{ 382 kgf*cm , 28 ft.*lbf }



6. DRAIN ENGINE COOLANT


A264221E01

NOTICE:
To avoid the danger of being burned, do not remove the water filler cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot coolant and steam to blow out from the radiator assembly.

Text in Illustration 
*1
Water Filler Cap Sub-assembly
*2
Radiator Drain Cock Plug
*3
Cylinder Block Drain Cock Plug
  1. Loosen the radiator drain cock plug.

  1. Remove the water filler cap sub-assembly.

  1. Loosen the cylinder block drain cock plug, then drain the coolant.



7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


8. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY
(Click here)


9. REMOVE FRONT NO. 1 VENTILATOR SEAL (for LHD)


C242062
  1. Disengage the clamp and remove the front No. 1 ventilator seal.



10. REMOVE FRONT NO. 1 VENTILATOR SEAL (for RHD)


A249556
  1. Disengage the clamp and remove the front No. 1 ventilator seal.



11. REMOVE FRONT AIR SHUTTER SEAL RH (for LHD)

HINT:
Use the same procedure as for the No. 1 ventilator seal.



12. REMOVE FRONT AIR SHUTTER SEAL RH (for RHD)

HINT:
Use the same procedure as for the No. 1 ventilator seal.



13. REMOVE INNER COWL TOP TO COWL BRACE (for LHD)


C242063
  1. Remove the 2 bolts and the inner cowl top to cowl brace.



14. REMOVE INNER COWL TOP TO COWL BRACE (for RHD)


A249554
  1. Remove the 2 bolts and the inner cowl top to cowl brace.



15. REMOVE OUTER COWL TOP PANEL (for LHD)


C242064
  1. Disengage the 2 clamps and separate the wire harness.



  1. Remove the 8 bolts and the outer cowl top panel.


    C242065



16. REMOVE OUTER COWL TOP PANEL (for RHD)


A249552
  1. Disengage the 2 clamps and separate the wire harness.



  1. Remove the 8 bolts and the outer cowl top panel.


    A249553



17. REMOVE BATTERY


A248909
  1. Disconnect the cable from the battery terminal.

  1. Loosen the 2 nuts and remove the battery clamp.

  1. Remove the battery.



18. REMOVE BATTERY TRAY


19. REMOVE NO. 2 CYLINDER HEAD COVER


    A116235
  1. Remove the 4 nuts and No. 2 cylinder head cover.



20. REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE


    A249575
  1. Disconnect the fuel vapor feed hose from the vacuum switching valve assembly and air cleaner hose.

  1. Loosen the 2 hose clamps and disconnect the fuel vapor feed hose assembly from the No. 1 air cleaner hose and vacuum switching valve assembly.



    A249576
  1. Disconnect the No. 2 fuel vapor feed hose from the intake manifold.



    A249577
  1. Disengage the 2 clamps and disconnect the wire harness from the air cleaner cap sub-assembly and vacuum switching valve assembly.

  1. Disconnect the mass air flow meter connector.

  1. Disconnect the vacuum switching valve connector.



    A249578
  1. Loosen the hose clamp and disconnect the No. 1 air cleaner hose from the throttle with motor body assembly.

  1. Disengage the 2 clamps and remove the air cleaner cap sub-assembly with No. 1 air cleaner hose.



21. REMOVE NO. 1 IGNITION COIL
(Click here)


22. DISCONNECT NO. 3 RADIATOR HOSE


A116580
  1. Disconnect No. 3 radiator hose.



23. DISCONNECT RESERVE TANK HOSE


A116581
  1. Disconnect the reserve tank hose.



24. REMOVE WATER FILLER SUB-ASSEMBLY


A116739
  1. Separate No. 1 radiator hose from the cylinder head.

  1. Remove the 2 nuts and the water filler sub-assembly.



25. DISCONNECT NO. 2 WATER BY-PASS HOSE


A116740
  1. Disconnect No. 2 water by-pass hose.



26. DISCONNECT WATER BY-PASS HOSE


A116741
  1. Disconnect the water by-pass hose.



27. DISCONNECT THROTTLE WITH MOTOR BODY CONNECTOR


A268158
  1. Separate the wire harness clamp.

  1. Remove the nut and separate the throttle with motor body connector.



28. DISCONNECT VENTILATION HOSE


A116973
  1. Disconnect the ventilation hose.



29. DISCONNECT UNION TO CONNECTOR TUBE HOSE


A116744
  1. Disconnect the union to connector tube hose.



30. REMOVE OIL LEVEL DIPSTICK SUB-ASSEMBLY


31. REMOVE INTAKE MANIFOLD


A268159
  1. Separate the 3 wire harness clamps shown in the illustration.



    A116746
  1. Remove the 3 bolts, 2 nuts and the intake manifold.



32. REMOVE OIL LEVEL DIPSTICK GUIDE


A268160
  1. Disengage the clamp and disconnect the wire harness from the oil level dipstick guide.

  1. Remove the bolt and the oil level dipstick guide.

  1. Remove the O-ring from the oil level dipstick guide.



33. DISCONNECT FUEL TUBE SUB-ASSEMBLY


    A115492
  1. Remove the EFI fuel pipe clamp.



    A260531E01
  1. Pinch the retainer of the fuel tube connector, then pull the fuel tube connector to disconnect the fuel tube out of the fuel delivery pipe sub-assembly.
    Text in Illustration 
    *1
    Retainer
    *2
    Fuel Pipe
    *3
    O-Ring
    *4
    Nylon Tube
    V100135
    Pinch
    V100136
    Pull

    NOTICE:
    1. Remove any dirt and foreign matter from the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting, as the fuel tube connector has the O-ring that seals the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected parts by covering them with a vinyl bag after disconnecting the fuel tube.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.



34. DISCONNECT BOOSTER VACUUM TUBE


A116748
  1. Disconnect the booster vacuum tube.



35. DISCONNECT CAMSHAFT POSITION SENSOR CONNECTOR


A116749
  1. Disconnect the camshaft position sensor connector.



36. DISCONNECT ENGINE COOLANT TEMPERATURE SENSOR CONNECTOR


A116750
  1. Disconnect the engine coolant temperature sensor connector.



37. DISCONNECT HEATED OXYGEN SENSOR CONNECTOR


A116751
  1. Remove the bolts and separate the sensor bracket.

  1. Disconnect the heated oxygen sensor connector.



38. DISCONNECT INLET HEATER WATER HOSE A


A116752
  1. Disconnect inlet heater water hose A.



39. SEPARATE NO. 1 WATER BY-PASS PIPE


A116753
  1. Remove the bolt and separate No. 1 water by-pass pipe.



40. DISCONNECT WIRE HARNESS


A116755
  1. Remove the 2 bolts and disconnect the wire harness.



41. SEPARATE FRONT EXHAUST PIPE ASSEMBLY


A116756
  1. Remove the 2 bolts and 2 compression springs and separate the front exhaust pipe assembly.



42. REMOVE EXHAUST PIPE GASKET
  1. Remove the exhaust pipe gasket from the exhaust manifold.



43. REMOVE MANIFOLD SUPPORT BRACKET


A116757
  1. Remove the 3 bolts and the manifold support bracket.



44. REMOVE GENERATOR ASSEMBLY
(Click here)


45. REMOVE NO. 1 IGNITION COIL


    A156073
  1. Disconnect the 4 No. 1 ignition coil connectors.



    A156074
  1. Remove the 4 bolts and the 4 No. 1 ignition coils.



46. DISCONNECT VENTILATION HOSE


A115487
  1. Disconnect the ventilation hose.



47. DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY


A115488
  1. Disconnect the fuel vapor feed hose assembly.



48. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A115489
  1. Disconnect the fuel injector connectors.



  1. for LHD:



      A260540
    1. Disconnect the connector and 4 wire harness clamps shown in the illustration and disconnect the engine wire harness.



    2. A115491
    3. Remove the bolt and the wire harness bracket.



  1. for RHD:



      A260541
    1. Disconnect the connector and 3 wire harness clamps shown in the illustration and disconnect the engine wire harness.



    A066472
  1. Remove the 9 bolts, 2 nuts and 2 seal washers and then remove the cylinder head cover sub-assembly.



49. REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH


A245785
  1. Place a wooden block on a jack underneath the engine.



    A248250
  1. Remove the 4 bolts, 2 nuts and the engine mounting insulator sub-assembly RH.



50. REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY


A116203E05


  1. Set the No. 1 cylinder to TDC/compression.

    1. Turn the crankshaft damper sub-assembly, and align its timing notch with timing mark "0" of the oil pump.
      Text in Illustration 
      *a
      Timing Notch



    2. A116204E07
    3. Check that the timing marks on the camshaft timing sprocket and the camshaft timing gear are all facing upward as shown in the illustration.
      Text in Illustration 
      *a
      Timing Marks
      If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.



    A250432E01
  1. Using SST, loosen the bolt while holding the crankshaft damper sub-assembly.
    Text in Illustration 
    *a
    Hold
    *b
    Loosen

    SST
    09213-58014   (90201-08131, 91111-50845)
    09330-00021   (09330-00030)

    NOTICE:
    Check the SST installation positions when installing them, to avoid the SST fixing bolts from coming into contact with the oil pump assembly.

  1. Remove the SSTs and the bolt.

  1. Remove the crankshaft damper sub-assembly.



51. REMOVE CRANKSHAFT POSITION SENSOR


    A182411
  1. Disconnect the crankshaft position sensor connector.

  1. Remove the bolt and crankshaft position sensor.

    NOTICE:
    If a component has been dropped or subjected to a strong impact, replace it.



52. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


    A116177
  1. Disconnect the camshaft timing oil control valve assembly connector.



    A116178
  1. Remove the bolt and camshaft timing oil control valve assembly.

  1. Remove the O-ring from the camshaft timing oil control valve assembly.



53. REMOVE WATER PUMP PULLEY


A065937
  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Remove the 3 bolts and the water pump pulley.



54. REMOVE ENGINE WATER PUMP ASSEMBLY


A065938
  1. Remove the 3 bolts and 2 nuts and remove the water pump assembly and water pump gasket.



55. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET


A116553
  1. Remove the 4 bolts and the transverse engine engine mounting bracket.



56. REMOVE OIL PUMP ASSEMBLY


A116554
  1. Remove the 15 bolts and the nut.



    A116555E01
  1. Using a screwdriver with its tip wrapped in protective tape, pry the oil pump assembly to remove it.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Do not damage the contact surfaces of the oil pump assembly and oil pan sub-assembly.



    A116556
  1. Remove the 2 O-rings from the cylinder block and oil pan sub-assembly.



57. REMOVE OIL PUMP SEAL


A166952E01
  1. Using a screwdriver with its tip wrapped in protective tape, remove the oil pump seal.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Splinter of Wood



58. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY


A156302E01

NOTICE:
  1. Do not rotate the crankshaft with the chain tensioner removed.
  2. When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC first, and align the oil jet hole with the paint mark. This prevents the pistons from coming into contact with the valves.
    Text in Illustration 
    *1
    Oil Jet
    *a
    Timing Mark (1 dot)



    A116564E03
  1. Pull up the stopper plate and hold it with its lock released.
    Text in Illustration 
    *1
    Stopper Plate



    A116565E03
  1. Unlock the plunger of the tensioner and push it in to the end.
    Text in Illustration 
    *1
    Plunger



    A116566E03
  1. Pull down the stopper plate with the plunger pushed to the end and lock the plunger.
    Text in Illustration 
    *1
    Stopper Plate



    A116567
  1. Insert a 3 mm (0.12 in.) diameter bar into the hole in the stopper plate and lock the plunger.



    A116568
  1. Remove the 2 bolts and the No. 1 chain tensioner assembly.



59. REMOVE CHAIN TENSIONER SLIPPER


A116569
  1. Remove the chain tensioner slipper.



60. REMOVE NO. 1 CHAIN VIBRATION DAMPER


A116570
  1. Remove the 2 bolts and the No. 1 chain vibration damper.



61. REMOVE CHAIN SUB-ASSEMBLY


62. REMOVE CAMSHAFT

NOTICE:
When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC first.



    A035758E04
  1. Using several steps, uniformly loosen and remove the 19 bearing cap bolts in the sequence shown in the illustration, and then remove No. 1 camshaft bearing cap and No. 2 camshaft bearing cap.

    NOTICE:
    Loosen each bolt uniformly while keeping the camshaft level.

  1. Remove the camshaft and No. 2 camshaft.



63. REMOVE CYLINDER HEAD SUB-ASSEMBLY


A035286
  1. Using several steps, uniformly loosen and remove the 10 cylinder head bolts with an 8 mm bi-hexagon wrench in the sequence shown in the illustration. Remove the 10 plate washers.

    NOTICE:
    1. Do not drop the washers into the cylinder head.
    2. Head warpage or cracking could result from removing the bolts in the wrong order.



64. REMOVE CYLINDER HEAD GASKET


A116758
  1. Remove the cylinder head gasket.