CAN COMMUNICATION SYSTEM (except Separate Type Yaw Rate Sensor) > Check CAN Bus Lines for Short Circuit (RHD Models) |
| Symptom | Trouble Area |
| The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω. |
|


| 1.CHECK SHORT IN CAN BUS WIRES (DLC3 BRANCH WIRE) |
Turn the ignition switch off.
Disconnect the F83 No. 2 junction connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F4-6 (CANH) - F4-14 (CANL) | Ignition switch off | 1 MΩ or higher |
| *a | Front view of DLC3 |
|
| ||||
| OK | |
| 2.CONNECT CONNECTOR |
Reconnect the F83 No. 2 junction connector.
| NEXT | |
| 3.CHECK SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR) |
Disconnect the A61 and F82 No. 1 junction connectors.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F4-6 (CANH) - F4-14 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Front view of DLC3 |
|
| ||||
| OK | |
| 4.CHECK SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - ECM) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A61-9 (CANH) - A61-20 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
|
| ||||
| OK | |
| 5.CHECK SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A61-10 (CANH) - A61-21 (CANL) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
|
| ||||
| OK | |
| 6.CHECK SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F82-1 (CANH) - F82-12 (CANL) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
|
| ||||
| OK | ||
| ||
| 7.CHECK SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR) |
Disconnect the F83 No. 2 junction connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F82-4 (CANH) - F82-15 (CANL) | Ignition switch off | 1 MΩ or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
|
| ||||
| OK | |
| 8.CONNECT CONNECTOR |
Reconnect the A61 and F82 No. 1 junction connectors.
| NEXT | |
| 9.CHECK SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F83-7 (CANH) - F83-18 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
|
| ||||
| OK | |
| 10.CHECK SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F83-8 (CANH) - F83-19 (CANL) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
|
| ||||
| OK | |
| 11.CHECK SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY)) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F83-1 (CANH) - F83-12 (CANL) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
|
| ||||
| OK | |
| 12.CHECK SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F83-6 (CANH) - F83-17 (CANL) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
|
| ||||
| OK | |
| 13.CHECK SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F83-4 (CANH) - F83-15 (CANL) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
|
| ||||
| OK | ||
| ||
| 14.CHECK SHORT IN CAN BUS WIRES (ECM MAIN WIRE) |
Disconnect the A74 ECM connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A61-9 (CANH) - A61-20 (CANL) | Ignition switch off | 1 MΩ or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| Result | Proceed to |
| NG | A |
| OK (for 1NZ-FE) | B |
| OK (for 2NZ-FE) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 15.CHECK SHORT IN CAN BUS WIRES (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) BRANCH WIRE) |
Disconnect the A54*1 or A55*2 skid control ECU (brake actuator assembly) connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A61-10 (CANH) - A61-21 (CANL) | Ignition switch off | 1 MΩ or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| Result | Proceed to |
| NG | A |
| OK (w/ VSC) | B |
| OK (w/o VSC) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 16.CHECK SHORT IN CAN BUS WIRES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH WIRE) |
Disconnect the F76 main body ECU (multiplex network body ECU) connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F82-1 (CANH) - F82-12 (CANL) | Ignition switch off | 1 MΩ or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
|
| ||||
| OK | ||
| ||
| 17.CHECK SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY MAIN WIRE) |
Disconnect the F1 combination meter assembly connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F83-7 (CANH) - F83-18 (CANL) | Ignition switch off | 1 MΩ or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
|
| ||||
| OK | ||
| ||
| 18.CHECK SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE) |
Disconnect the F42*1 or F41*2 air conditioning amplifier assembly connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F83-8 (CANH) - F83-19 (CANL) | Ignition switch off | 1 MΩ or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
|
| ||||
| OK | ||
| ||
| 19.CHECK SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) BRANCH WIRE) |
Disconnect the F30 steering angle sensor (spiral cable sub-assembly) connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F83-1 (CANH) - F83-12 (CANL) | Ignition switch off | 1 MΩ or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
|
| ||||
| OK | ||
| ||
| 20.CHECK SHORT IN CAN BUS WIRES (POWER STEERING ECU ASSEMBLY BRANCH WIRE) |
Disconnect the F6 power steering ECU assembly connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F83-6 (CANH) - F83-17 (CANL) | Ignition switch off | 1 MΩ or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
|
| ||||
| OK | ||
| ||
| 21.CHECK SHORT IN CAN BUS WIRES (AIRBAG SENSOR ASSEMBLY BRANCH WIRE) |
Disconnect the F16 airbag sensor assembly connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F83-4 (CANH) - F83-15 (CANL) | Ignition switch off | 1 MΩ or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
|
| ||||
| OK | ||
| ||