Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Built-in Type Yaw Rate Sensor)

VEHICLE STABILITY CONTROL SYSTEM (for Built-in Type Yaw Rate Sensor) > VSC OFF Indicator Light Remains ON

for Preparation Click here


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter via CAN communication.
Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction and VSC controls. If traction control turns OFF, the TRC OFF indicator light will come on.
If VSC and traction control turns OFF, the TRC OFF indicator and VSC OFF indicator light will come on.
The VSC OFF indicator light is illuminated when the VSC and TRC controls are prohibited by operating the VSC OFF switch.
By pressing the VSC OFF switch for 3 seconds or longer, the VSC OFF mode is activated, the VSC and TRC controls are prohibited, and both the VSC OFF indicator light and the TRC OFF indicator light in the combination meter are illuminated.

WIRING DIAGRAM


C243296E02


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the brake actuator assembly, perform zero point calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


2.CHECK CAN COMMUNICATION SYSTEM
  1. Check if CAN communication system DTCs are output (Click here).

Result 
Result
Proceed to
DTC is not output
A
DTC is output
B


B
CHECK CAN COMMUNICATION SYSTEM (Click here)
A


3.INSPECT BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1NZ-FE)
    B
    NG (for 2NZ-FE)
    C



B
CHECK AND REPLACE CHARGING SYSTEM OR BATTERY (Click here)

C
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY (Click here)
A


4.CHECK HARNESS AND CONNECTOR (CSW TERMINAL)
  1. Turn the ignition switch off.



    C243286E08
  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A54-30 (CSW) - Body ground
    VSC OFF Switch held on
    Below 1 Ω
    A54-30 (CSW) - Body ground
    VSC OFF Switch off (Not pressed)
    10 kΩ or higher

Text in Illustration 
*a
Front view of wire harness connector
(to skid control ECU)
  1. Reconnect the skid control ECU connector.



NG
Go to step 8
OK


5.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. According to the display on the tester, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    TRC/VSC Off Mode
    TRC/VSC off mode/Normal, TRC OFF, Unknown or VSC OFF
    Normal: Normal mode TRC OFF: TRC OFF mode
    Unknown: Unspecified
    VSC OFF: TRC, VSC OFF mode
    -

  1. Check that the mode display changes according to the VSC OFF switch operation.

    OK:
    Display changes according to the switch operation.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


6.REPLACE COMBINATION METER ASSEMBLY
  1. Turn the ignition switch off.

  1. Replace the combination meter assembly (Click here).


NEXT


7.CHECK COMBINATION METER ASSEMBLY
  1. Connect the intelligent tester to the DLC3.

  1. Perform Active Test of the combination meter assembly using the intelligent tester (Click here).

    OK:
    The VSC OFF indicator light turns on or off in accordance with the intelligent tester.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK

END 

8.INSPECT VSC OFF SWITCH
  1. Remove the VSC OFF switch (Click here).

  1. Inspect the VSC OFF switch (Click here).

  1. Reconnect the VSC OFF switch connector.



NG
REPLACE VSC OFF SWITCH (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
  1. Disconnect the skid control ECU (brake actuator assembly) connector and the VSC OFF switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A54-30 (CSW) - F57-6
    Always
    Below 1 Ω
    F57-3 - Body ground
    Always
    Below 1 Ω
    A54-30 (CSW) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the skid control ECU (brake actuator assembly) connector and the VSC OFF switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)