DTC P0134 Oxygen Sensor Circuit No Activity Detected (Bank 1 Sensor 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0134 | Heated oxygen sensor (sensor 1) output does not indicate rich (more than 0.45 V) even once when conditions (a), (b), (c), (d) and (e) continue for more than 50 seconds (1 trip detection logic):
|
|
| Required Sensors/Components (Main) | Heated oxygen sensor (sensor 1) |
| Required Sensors/Components (Related) | Engine coolant temperature sensor, Throttle with motor body assembly, Crankshaft position sensor, Vehicle speed sensor |
| Frequency of Operation | Once per driving cycle |
| Intrusive closed loop is performed when following conditions met | - |
| Duration that the following conditions met | 50 seconds |
| Engine coolant temperature | 40°C (104°F) or higher |
| Engine speed | 1400 rpm or more |
| Vehicle speed | 40 km/h or more |
| Idle | OFF |
| Battery voltage | 11 V or more |
| Oxygen sensor voltage | Less than 0.45 V |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| O2S B1S1 (Heated oxygen sensor (sensor 1)) | +12% | Rich | Higher than 0.5 V |
| -12% | Lean | Below 0.4 V | |
| O2S B1S2 (Heated oxygen sensor (sensor 2)) | +12% | Rich | Higher than 0.5 V |
| -12% | Lean | Below 0.4 V |
| Case | Heated Oxygen Sensor (Sensor 1) Output Voltage | Heated Oxygen Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0134) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
| DTC P0134 is output | A |
| DTC P0134 and other DTCs are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (O2S B1S1) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S1 and Engine Speed.
Warm up the engine until the engine coolant temperature reaches more than 40°C (104°F).
Rev the engine up to 4000 rpm 3 times using the accelerator pedal.
Read the output voltage of the heated oxygen sensor (sensor 1) displayed on the tester when the engine speed is suddenly increased.
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 3.CHECK PCV HOSE CONNECTIONS |
Inspect the PCV hose connections (Click here).
|
| ||||
| OK | |
| 4.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE OF HEATED OXYGEN SENSOR (SENSOR 1)) |
Inspect the heated oxygen sensor (sensor 1) (Click here).
|
| ||||
| OK | |
| 5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1)) |
Disconnect the heated oxygen sensor (sensor 1) connector.
Turn the ignition switch to ON.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B37-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector ( to heated oxygen sensor (sensor 1)) |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM) |
Disconnect the heated oxygen sensor (sensor 1) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B37-1 (HT1A) - B84-109 (HT1A) | Always | Below 1 Ω |
| B37-3 (OX1A) - B84-112 (OX1A) | Always | Below 1 Ω |
| B37-4 (E2) - B84-90 (EX1A) | Always | Below 1 Ω |
| B37-1 (HT1A) or B84-109 (HT1A)- Body ground | Always | 10 kΩ or higher |
| B37-3 (OX1A) or B84-112 (OX1A) - Body ground | Always | 10 kΩ or higher |
| B37-4 (E2) or B84-90 (EX1A) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 8.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 9.INSPECT FUEL INJECTOR ASSEMBLY |
Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | |
| 10.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leak.
|
| ||||
| OK | ||
| ||
| 11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - NO. 1 INTEGRATION RELAY) |
Disconnect the heated oxygen sensor (sensor 1) connector.
Remove the No. 1 integration relay connector from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B37-2 (+B) - 1E-4 | Always | Below 1 Ω |
| B37-2 (+B) or 1E-4 Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 12.PERFORM CONFIRMATION DRIVING PATTERN |
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
| NEXT | |
| 13.CHECK WHETHER DTC OUTPUT RECURS (DTC P0134) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0134 is output | B |
|
| ||||
| A | |
| 14.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST |
Has the vehicle run out of fuel in the past?
|
| ||||
| YES | ||
| ||