Home › Engine / Hybrid System · 2NZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0134    Oxygen Sensor Circuit No Activity Detected (Bank 1 Sensor 1)

for Preparation Click here


DESCRIPTION

Refer to DTC P0031 .

HINT:
Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.


DTC No.
DTC Detection Condition
Trouble Area
P0134
Heated oxygen sensor (sensor 1) output does not indicate rich (more than 0.45 V) even once when conditions (a), (b), (c), (d) and (e) continue for more than 50 seconds (1 trip detection logic):
  1. (a) Engine speed: 1400 rpm or more
  2. (b) Vehicle speed: 40 km/h (25 mph) or more
  3. (c) Throttle valve not fully closed
  4. (d) 180 seconds or more after starting engine
  5. (e) Engine coolant temperature more than 40°C (104°F)
  1. Open or short in heated oxygen sensor (sensor 1) circuit
  2. Heated oxygen sensor heater (sensor 1)
  3. Heated oxygen sensor (sensor 1)
  4. Fuel pressure
  5. Intake system
  6. PCV hose connections
  7. PCV valve and hose
  8. Fuel injector assembly
  9. Exhaust gas leakage
  10. No. 1 integration relay (EFI MAIN relay)
  11. ECM

HINT:
If this DTC is stored, check the output voltage of the heated oxygen sensor (sensor 1) by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / O2S B1S1.


MONITOR DESCRIPTION

The ECM uses the heated oxygen sensor to optimize the air-fuel mixture with closed loop fuel control. This control helps decrease exhaust emissions by providing the catalyst with a nearly stoichiometric mixture. The sensor detects the oxygen level in the exhaust gas and the ECM uses this data to control the air-fuel ratio. The sensor output voltage range is from 0 V to 1 V. If the signal voltage is less than 0.45 V, the air-fuel ratio is lean. If the signal voltage is more than 0.45 V, the air-fuel ratio is rich. If the sensor does not indicate rich at least once despite the conditions for the closed loop fuel control being met and the specified time period has passed, the ECM will conclude that the closed loop fuel control is malfunctioning. The ECM will illuminate the MIL and a DTC is stored.

MONITOR STRATEGY


Required Sensors/Components (Main)
Heated oxygen sensor (sensor 1)
Required Sensors/Components (Related)
Engine coolant temperature sensor, Throttle with motor body assembly, Crankshaft position sensor, Vehicle speed sensor
Frequency of Operation
Once per driving cycle

TYPICAL ENABLING CONDITIONS


Intrusive closed loop is performed when following conditions met
-
Duration that the following conditions met
50 seconds
Engine coolant temperature
40°C (104°F) or higher
Engine speed
1400 rpm or more
Vehicle speed
40 km/h or more
Idle
OFF
Battery voltage
11 V or more

TYPICAL MALFUNCTION THRESHOLDS


Oxygen sensor voltage
Less than 0.45 V

CONFIRMATION DRIVING PATTERN


A219224E03

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the tester on [A].
  6. Start the engine and warm it up until the engine coolant temperature reaches 40°C (104°F) or higher [B].
  7. Drive the vehicle at 40 km/h (25 mph) or more for 4 minutes or more [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Enter the following menus: Powertrain / Engine and ECT / DTC [D].
  9. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0134.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [D] again.


WIRING DIAGRAM

Refer to DTC P0031 .

INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume function provided in the Active Test. The Control the Injection Volume function can help to determine whether the heated oxygen sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume operation using the intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Start the engine and turn the tester on.
  3. Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
  5. Perform the Active Test operation with the engine idling.
  6. Monitor the output voltages of the heated oxygen sensors (O2S B1S1 and O2S B1S2) displayed on the tester.

HINT:
  1. Change the fuel injection volume within the range of -12% to +12%. The injection volume can be changed in fine gradations.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


Tester Display
(Sensor)
Injection Volume
Status
Voltage
O2S B1S1
(Heated oxygen sensor (sensor 1))
+12%
Rich
Higher than 0.5 V
-12%
Lean
Below 0.4 V
O2S B1S2
(Heated oxygen sensor (sensor 2))
+12%
Rich
Higher than 0.5 V
-12%
Lean
Below 0.4 V

NOTICE:
The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.


Case
Heated Oxygen Sensor (Sensor 1) Output Voltage
Heated Oxygen Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E05
A150789E07
A150787E05
A150788E09
-
2
A150787E05
A150790E01
A150787E05
A150788E09
  1. Heated oxygen sensor (Sensor 1)
  2. Heated oxygen sensor heater (Sensor 1)
  3. Heated oxygen sensor circuit (Sensor 1)
3
A150787E05
A150789E07
A150787E05
A150790E01
  1. Heated oxygen sensor (Sensor 2)
  2. Heated oxygen sensor heater (Sensor 2)
  3. Heated oxygen sensor circuit (Sensor 2)
4
A150787E05
A150790E01
A150787E05
A150790E01
  1. Fuel injector assembly
  2. Fuel pressure
  3. Gas leak from exhaust system (Air-fuel ratio extremely rich or lean)

HINT:
  1. Following the Control the Injection Volume procedure enables technicians to check and graph the voltage outputs of both heated oxygen sensors
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / O2S B1S1 and O2S B1S2, then press the view button.

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0134)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC P0134 is output
    A
    DTC P0134 and other DTCs are output
    B

HINT:
If any DTCs other than P0134 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING INTELLIGENT TESTER (O2S B1S1)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S1 and Engine Speed.

  1. Warm up the engine until the engine coolant temperature reaches more than 40°C (104°F).

  1. Rev the engine up to 4000 rpm 3 times using the accelerator pedal.

  1. Read the output voltage of the heated oxygen sensor (sensor 1) displayed on the tester when the engine speed is suddenly increased.

    Standard Voltage:
    Heated oxygen sensor voltage output indicates 0.45 V or higher (rich signal) at least once.


    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 12
A


3.CHECK PCV HOSE CONNECTIONS
  1. Inspect the PCV hose connections (Click here).

OK:
PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


4.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE OF HEATED OXYGEN SENSOR (SENSOR 1))
  1. Inspect the heated oxygen sensor (sensor 1) (Click here).



NG
REPLACE HEATED OXYGEN SENSOR (SENSOR 1) (Click here)
OK


5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1))
  1. Disconnect the heated oxygen sensor (sensor 1) connector.

  1. Turn the ignition switch to ON.



    A079114E49
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B37-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    ( to Heated Oxygen Sensor (Sensor 1))



NG
Go to step 11
OK


6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)
  1. Disconnect the heated oxygen sensor (sensor 1) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B37-1 (HT1A) - B84-109 (HT1A)
    Always
    Below 1 Ω
    B37-3 (OX1A) - B84-112 (OX1A)
    Always
    Below 1 Ω
    B37-4 (E2) - B84-90 (EX1A)
    Always
    Below 1 Ω
    B37-1 (HT1A) or B84-109 (HT1A)- Body ground
    Always
    10 kΩ or higher
    B37-3 (OX1A) or B84-112 (OX1A) - Body ground
    Always
    10 kΩ or higher
    B37-4 (E2) or B84-90 (EX1A) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leakage from intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


8.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


9.INSPECT FUEL INJECTOR ASSEMBLY
  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


10.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leak.

OK:
No gas leak.



NG
REPAIR OR REPLACE EXHAUST GAS LEAKAGE POINT
OK

REPLACE HEATED OXYGEN SENSOR (SENSOR 1) (Click here)  

11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - NO. 1 INTEGRATION RELAY)
  1. Disconnect the heated oxygen sensor (sensor 1) connector.

  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B37-2 (+B) - 1E-4
    Always
    Below 1 Ω
    B37-2 (+B) or 1E-4 Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)  

12.PERFORM CONFIRMATION DRIVING PATTERN
  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


NEXT


13.CHECK WHETHER DTC OUTPUT RECURS (DTC P0134)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0134 is output
    B



B
REPLACE ECM (Click here)
A


14.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
  1. Has the vehicle run out of fuel in the past?



NO
CHECK FOR INTERMITTENT PROBLEMS (Click here)
YES

DTC CAUSED BY RUNNING OUT OF FUEL