Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Separate Type Yaw Rate Sensor)

DTC    C1381    Acceleration Sensor Power Supply Voltage Malfunction

for Preparation Click here


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and deceleration sensor (yaw rate sensor) via the CAN communication system.
The yaw rate and deceleration sensor (yaw rate sensor) has a built in deceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2). If there is trouble in the bus lines between the yaw rate and deceleration sensor (yaw rate sensor) and the CAN communication system, the DTCs U0123 (Lost Communication with Yaw Rate Sensor Module) and U0124 (Lost Communication with Lateral Acceleration Sensor Module) are output.
These DTCs are also output when calibration has not been completed.

DTC No.
DTC Detection Condition
Trouble Area
C1381
At a vehicle speed of more than 3 km/h (2 mph), the acceleration sensor power source malfunction signal is received for 10 seconds or more.
  1. Yaw rate and deceleration sensor (Yaw rate sensor)
  2. Yaw rate and deceleration sensor (Yaw rate sensor) power source circuit

WIRING DIAGRAM

Refer to DTCs C1232, C1243, C1245 and C1473 .

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the brake actuator assembly, perform zero point calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK TERMINAL VOLTAGE (IG TERMINAL)


    C208309E35
  1. Disconnect the yaw rate and deceleration sensor (yaw rate sensor) connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F122-4 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate and Deceleration Sensor (Yaw Rate Sensor))

  1. Turn the ignition switch off.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG CIRCUIT)
OK


2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)


    C208309E36
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F122-1 (GND) - Body ground
    Always
    Below 1 Ω

    NOTICE:
    Check the yaw rate and deceleration sensor (yaw rate sensor) signal after replacement (Click here).

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).

Text in Illustration 
*a
Front view of wire harness connector
(to Yaw Rate and Deceleration Sensor (Yaw Rate Sensor))
  1. Reconnect the yaw rate and deceleration sensor (yaw rate sensor) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


3.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Perform a road test.

  1. Check if the same DTC is recorded (Click here).

Result 
Result
Proceed to
DTC C1381 is not output
A
DTC C1381 is output
B


B
REPLACE YAW RATE AND DECELERATION SENSOR (YAW RATE SENSOR) (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)