DTC B1633/81 Rear Airbag Sensor Assembly RH Initialization Incomplete |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1633/81 |
|
|


| 1.SYSTEM CHECK |
Check the vehicle specifications.
| Result | Proceed to |
| for 3 Door | A |
| for 5 Door | B |
|
| ||||
| A | |
| 2.CHECK HISTORY DTC |
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for history DTCs (Click here).
|
| ||||
| OK | |
| 3.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the airbag sensor assembly, door side airbag sensor RH and No. 2 side airbag sensor assembly RH.
Disconnect the connectors from the airbag sensor assembly, door side airbag sensor RH and No. 2 side airbag sensor assembly RH.
Check that the terminals of connectors are not damaged.
|
| ||||
| OK | |
| 4.CHECK FLOOR WIRE (OPEN) |
Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

| *1 | No. 2 Side Airbag Sensor Assembly RH | *2 | Airbag Sensor Assembly |
| *3 | Floor Wire | *4 | Connector B |
| *5 | Connector C | *6 | Service Wire |
| *a | Front view of wire harness connector (to Airbag Sensor Assembly) | *b | Front view of wire harness connector (to No. 2 Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K46-3 (BCR-) - K46-4 (BCR+) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK FLOOR WIRE (SHORT) |
![]() |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K46-3 (BCR-) - K46-4 (BCR+) | Always | 1 MΩ or higher |
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Connector C |
| *a | Front view of wire harness connector (to No. 2 Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 6.CHECK FLOOR WIRE (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| K46-3 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
| K46-4 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Connector C |
| *a | Front view of wire harness connector (to No. 2 Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 7.CHECK FLOOR WIRE (SHORT TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K46-3 (BCR-) - Body ground | Always | 1 MΩ or higher |
| K46-4 (BCR+) - Body ground | Always | 1 MΩ or higher |
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Connector C |
| *a | Front view of wire harness connector (to No. 2 Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 8.CHECK FLOOR WIRE AND FRONT DOOR WIRE RH (OPEN) |
Using the service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.

| *1 | Door Side Airbag Sensor RH | *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH | *4 | Floor Wire |
| *5 | Connector B | *6 | Connector E |
| *7 | Service Wire | - | - |
| *a | Front view of wire harness connector (to No. 2 Side Airbag Sensor Assembly RH) | *b | Front view of wire harness connector (to Door Side Airbag Sensor RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K46-1 (BDR+) - K46-2 (BDR-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 9.CHECK FLOOR WIRE AND FRONT DOOR WIRE RH (SHORT) |
![]() |
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K46-1 (BDR+) - K46-2 (BDR-) | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Connector B |
| *a | Front view of wire harness connector (to No. 2 Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 10.CHECK FLOOR WIRE AND FRONT DOOR WIRE RH (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| K46-1 (BDR+) - Body ground | Ignition switch ON | Below 1 V |
| K46-2 (BDR-) - Body ground | Ignition switch ON | Below 1 V |
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Connector B |
| *a | Front view of wire harness connector (to No. 2 Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 11.CHECK FLOOR WIRE AND FRONT DOOR WIRE RH (SHORT TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K46-1 (BDR+) - Body ground | Always | 1 MΩ or higher |
| K46-2 (BDR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Connector B |
| *a | Front view of wire harness connector (to No. 2 Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 12.CHECK NO.2 SIDE AIRBAG SENSOR ASSEMBLY RH |
![]() |
Connect the connectors to the door side airbag sensor RH and airbag sensor assembly.
Interchange the No. 2 side airbag sensor assembly RH with the No. 2 side airbag sensor assembly LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1633/81 is output. | A |
| DTC B1638/82 is output. | B |
| DTC B1633/81 or B1638/82 is not output. | C |
| *1 | No. 2 Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the No. 2 side airbag sensor assembly RH and the No. 2 side airbag sensor assembly LH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
| A | |
| 13.CHECK DOOR SIDE AIRBAG SENSOR RH |
![]() |
Interchange the door side airbag sensor RH with the door side airbag sensor LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1633/81 or B1638/82 is not output. | A |
| DTC B1633/81 is output. | B |
| DTC B1638/82 is output. | C |
| *1 | Door Side Airbag Sensor LH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the door side airbag sensor LH and the door side airbag sensor RH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
| A | ||
| ||
| 14.CHECK FRONT DOOR WIRE RH (OPEN) |
Disconnect the floor wire connector from the front door wire RH.

| *1 | Door Side Airbag Sensor RH | *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH | *4 | Floor Wire |
| *5 | Connector D | *6 | Connector E |
| *7 | Service Wire | - | - |
| *a | Front view of wire harness connector (to Floor Wire) | *b | Front view of wire harness connector (to No. 2 Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| GK2-1 (BDR+) - GK2-2 (BDR-) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 15.CHECK FRONT DOOR WIRE RH (SHORT) |
![]() |
Disconnect the floor wire connector from the front door wire RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| GK2-1 (BDR+) - GK2-2 (BDR-) | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Connector D |
| *a | Front view of wire harness connector (to Floor Wire) |
|
| ||||
| OK | ||
| ||
| 16.CHECK FRONT DOOR WIRE RH (SHORT TO B+) |
Turn the ignition switch off.
![]() |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the front door wire connector from the floor wire.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| GK2-1 (BDR+) - Body ground | Ignition switch ON | Below 1 V |
| GK2-2 (BDR-) - Body ground | Ignition switch ON | Below 1 V |
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Connector D |
| *a | Front view of wire harness connector (to Floor Wire) |
|
| ||||
| OK | ||
| ||
| 17.CHECK FRONT DOOR WIRE RH (SHORT TO GROUND) |
![]() |
Disconnect the front door wire connector from the floor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| GK2-1 (BDR+) - Body ground | Always | 1 MΩ or higher |
| GK2-2 (BDR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Connector D |
| *a | Front view of wire harness connector (to Floor Wire) |
|
| ||||
| OK | ||
| ||
| 18.CHECK FLOOR WIRE (OPEN) |
Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

| *1 | No. 2 Side Airbag Sensor Assembly RH | *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire | *4 | Connector B |
| *5 | Connector C | *6 | Service Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) | *b | Front view of wire harness connector (to No. 2 Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K22-1 (BCR+) - K22-2 (BCR-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 19.CHECK FLOOR WIRE (SHORT) |
![]() |
Disconnect the service wire from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K22-1 (BCR+) - K22-2 (BCR-) | Always | 1 MΩ or higher |
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *4 | Connector B |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 20.CHECK FLOOR WIRE (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| K22-1 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| K22-2 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *4 | Connector B |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 21.CHECK FLOOR WIRE (SHORT TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K22-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| K22-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *4 | Connector B |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 22.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH |
![]() |
Connect the connectors to the No. 2 side airbag sensor assembly RH and airbag sensor assembly.
Interchange the side airbag sensor assembly RH with the side airbag sensor assembly LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1633/81 is output. | A |
| DTC B1638/82 is output. | B |
| DTC B1633/81 or B1638/82 is not output. | C |
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the side airbag sensor assembly RH and the side airbag sensor assembly LH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
| A | |
| 23.CHECK NO.2 SIDE AIRBAG SENSOR ASSEMBLY RH |
![]() |
Interchange the No. 2 side airbag sensor assembly RH with the No. 2 side airbag sensor assembly LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1633/81 or B1638/82 is not output. | A |
| DTC B1633/81 is output. | B |
| DTC B1638/82 is output. | C |
| *1 | No. 2 Side Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly RH |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the No. 2 side airbag sensor assembly LH and the No. 2 side airbag sensor assembly RH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
| A | ||
| ||