Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch

for Preparation Click here


DESCRIPTION

If the manual up and down function can be performed but the auto up and down function cannot, then the fail-safe mode may be functioning.
If the power window initialization has not been performed, the auto up and down function will not operate (Click here).

WIRING DIAGRAM


B291671E01


B291671E02


INSPECTION PROCEDURE

NOTICE:
  1. When the power window regulator motor assembly LH or RH (driver side) is reinstalled or replaced, the power window control system must be initialized.
  2. After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be resumed by repeating the following operations at least 5 times:
    1. Close the power window by fully pulling up the power window regulator master switch assembly and holding it in the auto up position.
    2. Open the power window by fully pushing down the power window regulator master switch assembly.

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / D-Door Motor / Data List.

  1. According to the display on the intelligent tester, perform the Data List.

    D-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Auto SW
    Driver side power window auto switch signal /
    OFF or ON
    OFF: Driver side door power window auto switch not operated
    ON: Driver side door power window auto switch operated
    -

    OK:
    Normal conditions listed above are displayed.



NG
Go to step 4
OK


2.PERFORM INITIALIZATION
  1. Initialize the power window regulator motor assembly LH or RH (driver side) (Click here).


NEXT


3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)
  1. Check that the driver side door power window moves when the auto up and down function of the power window regulator master switch assembly is operated (Click here).

    OK:
    Driver side auto up and down function is normal.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH OR RH (Click here)
OK

END 

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
  1. Inspect the power window regulator master switch assembly (Click here).



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR LH OR RH)
  1. for LHD

    1. Disconnect the H1 power window regulator master switch assembly connector.

    2. Disconnect the H3 power window regulator motor assembly LH (driver side) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      w/ Rear Power Window 
      Tester Connection
      Condition
      Specified Condition
      H1-4 (AUTO) - H3-4 (AUTO)
      Always
      Below 1 Ω
      H1-1 (GND) - Body ground
      Always
      Below 1 Ω
      H1-4 (AUTO) - Body ground
      Always
      10 kΩ or higher
      w/o Rear Power Window 
      Tester Connection
      Condition
      Specified Condition
      H1-1 (AUTO) - H3-4 (AUTO)
      Always
      Below 1 Ω
      H1-7 (GND) - Body ground
      Always
      Below 1 Ω
      H1-1 (AUTO) - Body ground
      Always
      10 kΩ or higher

  1. for RHD

    1. Disconnect the G1 power window regulator master switch assembly connector.

    2. Disconnect the G3 power window regulator motor assembly RH (driver side) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      w/ Rear Power Window 
      Tester Connection
      Condition
      Specified Condition
      G1-4 (AUTO) - G3-4 (AUTO)
      Always
      Below 1 Ω
      G1-9 (GND) - Body ground
      Always
      Below 1 Ω
      G1-4 (AUTO) - Body ground
      Always
      10 kΩ or higher
      w/o Rear Power Window 
      Tester Connection
      Condition
      Specified Condition
      G1-18 (AUTO) - G3-4 (AUTO)
      Always
      Below 1 Ω
      G1-7 (GND) - Body ground
      Always
      Below 1 Ω
      G1-18 (AUTO) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH OR RH (Click here)