Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    B1441/41    Air Mix Damper Control Servo Motor Circuit (Passenger Side)

for Preparation Click here


DESCRIPTION

The No. 1 air conditioning radiator damper servo sub-assembly (air mix servo motor) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air mix servo motor to any position. As a result, the air mix servo motor varies the mixture of hot air from the heater core and cold air from the evaporator so that the temperature of the air is as requested.

HINT:
Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.


DTC No.
DTC Detection Condition
Trouble Area
B1441/41
The air mix damper position does not change when the air conditioning amplifier assembly operates the No. 1 air conditioning radiator damper servo sub-assembly (air mix servo motor).
  1. No. 1 air conditioning radiator damper servo sub-assembly (air mix servo motor)
  2. Air conditioning harness assembly
  3. Air conditioning amplifier assembly

WIRING DIAGRAM


E231121E01


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Mix Servo Targ Pulse (D)
    Air mix servo motor target pulse /
    Min.: 0
    Max.: 255
    1. MAX COOL: 4 (pulse)
    2. MAX HOT: 93 (pulse)
    -
    Air Mix Servo Actual Pulse (D)
    Air mix servo motor actual pulse /
    Min.: 0
    Max.: 255
    Follows the target pulse
    -

    OK:
    The display is as specified in the normal condition column.

    Result 
    Result
    Proceed to
    OK (When troubleshooting according to the DTC)
    A
    OK (When troubleshooting according to Problem Symptoms Table)
    B
    NG
    C



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
Go to step 3
A


2.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1441/41 is not output



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Active Test.

  1. According to the display on the intelligent tester, perform the Active Test.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Air Mix Servo Targ Pulse (D)
    Air mix servo motor pulse
    Min.: 0, Max.: 255
    Perform Active Test when value between 4 and 93 displayed

    OK:
    No. 1 air conditioning radiator damper servo sub-assembly (air mix servo motor) operates normally.



NG
Go to step 4
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

4.REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX SERVO MOTOR)
  1. Replace the No. 1 air conditioning radiator damper servo sub-assembly (air mix servo motor) (Click here).

    HINT:
    Since the No. 1 air conditioning radiator damper servo sub-assembly (air mix servo motor) cannot be inspected while it is removed from the vehicle, replace the No. 1 air conditioning radiator damper servo sub-assembly (air mix servo motor) with a new or normally functioning one.


NEXT


5.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1441/41 is not output



NG
Go to step 6
OK

END (NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX SERVO MOTOR) IS FAULTY) 

6.REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY
  1. Temporarily replace the air conditioning amplifier assembly with a new or normally functioning one (Click here).


NEXT


7.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1441/41 is not output



NG
REPLACE AIR CONDITIONING HARNESS ASSEMBLY (Click here)
OK

END (AIR CONDITIONING AMPLIFIER ASSEMBLY IS FAULTY)