Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start up the engine.

  1. A/C switch on.

  1. Turn the blower switch to on.

  1. Operate the cooler compressor with an engine speed of approximately 1000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the remaining compressor oil from each component, in the cooler compressor.

  1. Stop the engine.



    I106568E01
  1. Remove the caps from the service valves on the refrigerant line.
    Text in Illustration 
    *1
    High Pressure Service Valve
    *2
    Low Pressure Service Valve

  1. Connect the refrigerant recovery unit.

  1. Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.

    HINT:
    Use the refrigerant recovery unit in accordance with the manufacturer's instruction manual.



3. DRAIN ENGINE COOLANT (for 1NZ-FE)


A264221E01

NOTICE:
To avoid the danger of being burned, do not remove the water filler cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot coolant and steam to blow out from the radiator assembly.

Text in Illustration 
*1
Water Filler Cap Sub-assembly
*2
Radiator Drain Cock Plug
*3
Cylinder Block Drain Cock Plug
  1. Loosen the radiator drain cock plug.

  1. Remove the water filler cap sub-assembly.

  1. Loosen the cylinder block drain cock plug, then drain the coolant.



4. DRAIN ENGINE COOLANT (for 2NZ-FE)


A264221E01

NOTICE:
To avoid the danger of being burned, do not remove the water filler cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot coolant and steam to blow out from the radiator assembly.

Text in Illustration 
*1
Water Filler Cap Sub-assembly
*2
Radiator Drain Cock Plug
*3
Cylinder Block Drain Cock Plug
  1. Loosen the radiator drain cock plug.

  1. Remove the water filler cap sub-assembly.

  1. Loosen the cylinder block drain cock plug, then drain the coolant.



5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


6. REMOVE WINDSHIELD WIPER MOTOR AND LINK
(Click here)


7. REMOVE FRONT NO. 1 VENTILATOR SEAL


C242062
  1. Disengage the clamp and remove the front No. 1 ventilator seal.



8. REMOVE FRONT AIR SHUTTER SEAL RH

HINT:
Use the same procedure as for the No. 1 ventilator seal.



9. REMOVE COWL TOP TO COWL INNER BRACE


C242063
  1. Remove the 2 bolts and the inner cowl top to cowl brace.



10. REMOVE COWL TOP OUTER PANEL


C242064
  1. Disengage the 2 clamps and separate the wire harness.



  1. Remove the 8 bolts and the outer cowl top panel.


    C242065



11. DISCONNECT SUCTION TUBE SUB-ASSEMBLY B


    I105937
  1. Remove the bolt.

  1. Turn the hook connector clockwise and disconnect the suction tube.

  1. Remove the O-ring from the suction tube.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



12. DISCONNECT LIQUID TUBE SUB-ASSEMBLY A
  1. Disconnect the liquid tube.

  1. Remove the O-ring from the liquid tube.

    NOTICE:
    Seal the opening of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



13. DISCONNECT HEATER WATER OUTLET HOSE A


    I105939
  1. Slide the clip and disconnect the heater water outlet hose from the air conditioning unit.



14. DISCONNECT HEATER WATER INLET HOSE A


    I105940
  1. Slide the clip and disconnect the heater water inlet hose from the air conditioning unit.



15. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)


16. REMOVE STEERING COLUMN ASSEMBLY (for LHD)
(Click here)


17. REMOVE STEERING COLUMN ASSEMBLY (for RHD)
(Click here)


18. REMOVE HEATER TO REGISTER DUCT ASSEMBLY


    I106173
  1. Disengage the 3 claws and remove the heater to register duct.



19. REMOVE DEFROSTER NOZZLE ASSEMBLY


    I106174
  1. Disconnect the connectors and disengage the clamps, then disconnect the wire harness.



    I106175
  1. Disengage the 2 claws and 3 guides and remove the defroster nozzle.



20. SEPARATE DRAIN COOLER HOSE


    I106180
  1. Separate the drain cooler hose.



21. REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY


    I106239
  1. Disengage the 2 clamps.

  1. Remove the 2 bolts, nut and screw, then remove the instrument panel brace.

    HINT:
    If the vehicle is equipped with knee airbag, remove the knee airbag bracket mounting bolt.



22. REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    I105929
  1. Disengage the clamps.

  1. Disconnect the connectors on the front side.

  1. Remove the bolt and separate the instrument panel junction block.



    I106069E01
  1. Disconnect the back side connectors and remove the instrument panel junction block as shown in the illustration.



23. SEPARATE INSTRUMENT PANEL WIRE (for LHD)


    I105973
  1. Disconnect the connectors.

  1. Remove the screw.

  1. Disengage the 2 clamps and separate the connector holder.



    I106181
  1. Remove the screw and the wire harness protector.



    I105952
  1. Disconnect the connectors.

  1. Remove the bolt.

  1. Disengage the 3 clamps and remove the connector holder.



    I106870
  1. for Automatic Air Conditioning System:

    1. Disconnect the 3 connectors.

    2. Disengage the 2 clamps and disconnect the instrument panel wire.



    I106183
  1. for Manual Air Conditioning System:

    1. Disconnect the 3 connectors.

    2. Disengage the 3 clamps and disconnect the instrument panel wire.



  1. Remove the bolts and disconnect the ground wire.


    I106184

  1. Disconnect the connectors and clamps, then disconnect the instrument panel wire.



24. SEPARATE INSTRUMENT PANEL WIRE (for RHD)


    I105973
  1. Disconnect the connectors.

  1. Remove the screw.

  1. Disengage the 2 clamps and separate the connector holder.



    I106068
  1. Remove the screw and the wire harness protector.



    I105952
  1. Disconnect the connectors.

  1. Remove the bolt.

  1. Disengage the 3 clamps and remove the connector holder.



    I105954
  1. for Automatic Air Conditioning System:

    1. Disconnect the 2 connectors.

    2. Disengage the 3 clamps and disconnect the instrument panel wire.



    I105955
  1. for Manual Air Conditioning System:

    1. Disconnect the 3 connectors.

    2. Disengage the 5 clamps and disconnect the instrument panel wire.



  1. Remove the bolts and disconnect the ground wire.


    I106830

  1. Disconnect the connectors and clamps, then disconnect the instrument panel wire.



25. REMOVE INSTRUMENT PANEL REINFORCEMENT


  1. Remove the 8 bolts and 3 screws, then remove the instrument panel reinforcement.


    I106185



26. REMOVE AIR CONDITIONER UNIT ASSEMBLY


  1. Remove the 3 bolts and nut, then remove the air conditioner unit.


    I106186



27. REMOVE AIR CONDITIONING HARNESS ASSEMBLY (for LHD)


    I106580
  1. Disconnect the connectors and disengage the clamps, then remove the air conditioning harness.



28. REMOVE AIR CONDITIONING HARNESS ASSEMBLY (for RHD)


    I105959
  1. Disconnect the connectors and disengage the clamps, then remove the air conditioning harness.



29. REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY (for Automatic Air Conditioning System)


    I106864
  1. Disconnect the connector.

  1. Remove the screw.

  1. Disengage the claw and remove the air conditioning amplifier as shown in the illustration.



30. REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY (for Manual Air Conditioning System)


    I106865
  1. Remove the screw.

  1. Disengage the claw and remove the air conditioning amplifier as shown in the illustration.



31. REMOVE AIR CONDITIONING RADIATOR ASSEMBLY


    I106190
  1. Remove the 3 screws and the air conditioning radiator.



32. REMOVE COOLER AIR HOSE (for Automatic Air Conditioning System)


    I105964
  1. Remove the cooler air hose.



33. REMOVE NO. 1 AIR DUCT


    I106191
  1. Disengage the 3 claws and remove the air duct.



34. REMOVE NO. 2 AIR DUCT


    I105966
  1. Disengage the 3 claws and remove the air duct.