Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    B1442/42    Air Inlet Damper Control Servo Motor Circuit

for Preparation Click here


DESCRIPTION

The No. 1 blower damper servo sub-assembly (air inlet servo motor) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air inlet servo motor to any position, which controls the intake air settings (fresh, fresh/recirculation and recirculation).

HINT:
Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.


DTC No.
DTC Detection Condition
Trouble Area
B1442/42
The air inlet servo motor position does not change when the air conditioning amplifier assembly operates the No. 1 blower damper servo sub-assembly (air inlet servo motor).
  1. No. 1 blower damper servo sub-assembly (air inlet servo motor)
  2. Air conditioning harness assembly
  3. Air conditioning amplifier assembly

WIRING DIAGRAM


E228241E02


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Inlet Damper Targ Pulse
    Air inlet servo motor target pulse /
    Min.: 0
    Max.: 255
    1. Recirculation: 6 (pulse)
    2. Fresh: 22 (pulse)
    -
    Air Inlet Damper Actual Pulse
    Air inlet servo motor actual pulse /
    Min.: 0
    Max.: 255
    Follows the target pulse
    -

    OK:
    The display is as specified in the normal condition column.

    Result 
    Result
    Proceed to
    OK (When troubleshooting according to the DTC)
    A
    OK (When troubleshooting according to Problem Symptoms Table)
    B
    NG
    C



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
Go to step 3
A


2.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1442/42 is not output



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Active Test.

  1. According to the display on the intelligent tester, perform the Active Test.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Air Inlet Damper Targ Pulse
    Air inlet damper target pulse
    Min.: 0, Max.: 255
    Perform Active Test when value between 6 and 22 displayed

    OK:
    No. 1 blower damper servo sub-assembly (air inlet servo motor) operates normally.



NG
Go to step 4
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

4.REPLACE NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR INLET SERVO MOTOR)
  1. Replace the No. 1 blower damper servo sub-assembly (air inlet servo motor) (Click here).

    HINT:
    Since the No. 1 blower damper servo sub-assembly (air inlet servo motor) cannot be inspected while it is removed from the vehicle, replace the No. 1 blower damper servo sub-assembly (air inlet servo motor) with a new or normally functioning one.


NEXT


5.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1442/42 is not output



NG
Go to step 6
OK

END (NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR INLET SERVO MOTOR) IS FAULTY) 

6.REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY
  1. Temporarily replace the air conditioning amplifier assembly with a new or normally functioning one (Click here).


NEXT


7.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1442/42 is not output



NG
REPLACE AIR CONDITIONING HARNESS ASSEMBLY (Click here)
OK

END (AIR CONDITIONING AMPLIFIER ASSEMBLY IS FAULTY)