Home › Vehicle Exterior › DOOR / HATCH › FUEL LID LOCK CONTROL CABLE ASSEMBLY (for 5 Door)

FUEL LID LOCK CONTROL CABLE ASSEMBLY (for 5 Door) > INSTALLATION

for Preparation Click here



1. INSTALL FUEL FILLER OPENING LID LOCK RETAINER


    B268974E01
  1. Align the 2 claws B of the fuel filler opening lid lock retainer with the 2 slits.

  1. Push in and install the fuel filler opening lid lock retainer while securely engaging the 2 claws A.
    Text in Illustration 
    *1
    Claw A
    *2
    Claw B
    *3
    Slit



2. INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for LHD)


  1. Engage the 4 clamps and install the fuel lid lock control cable as shown in the illustration.


    B284618E01


    Text in Illustration 
    *1
    Fuel Lid Lock Control Cable Sub-assembly
    *2
    Wire Harness Clamp



    B273450
  1. Engage the 2 claws and install the fuel lid lock control cable.



3. INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for RHD)


  1. Engage the 7 clamps and install the fuel lid lock control cable as shown in the illustration.


    B271663E01


    Text in Illustration 
    *1
    Fuel Lid Lock Control Cable Sub-assembly
    *2
    Wire Harness Clamp



    B273450
  1. Engage the 2 claws and install the fuel lid lock control cable.



4. INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
  1. Connect the fuel lid lock control cable.



    B284627
  1. Engage the guide.

  1. Install the fuel lid lock open lever with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



5. INSTALL FRONT FLOOR CARPET ASSEMBLY
  1. Engage the 6 clamps.

  1. Install the front floor carpet with the clip.



6. INSTALL JACK ASSEMBLY


7. INSTALL JACK COVER


8. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

HINT:
Use the same procedure as for the RH side



9. INSTALL NO. 2 ROOM LIGHT ASSEMBLY (w/ Luggage Compartment Room Light)
  1. Connect the connector.



    E222046
  1. Engage the claw to install the No. 2 room light assembly.



10. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP
  1. Install the rear door opening trim weatherstrip.



11. INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side



12. INSTALL REAR FLOOR FINISH PLATE
  1. Engage the 4 guides and the 4 claws to install the rear floor finish plate.



13. INSTALL REAR DOOR SCUFF PLATE RH
  1. Engage the guide and the 5 claws and install the rear door scuff plate.



14. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



15. INSTALL COWL SIDE TRIM BOARD RH
  1. Engage the clip.

  1. Install the cowl side trim board with clip.



16. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



17. INSTALL FRONT DOOR SCUFF PLATE RH
  1. Engage the 8 claws and install the front door scuff plate.



18. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



19. INSTALL REAR CONSOLE BOX ASSEMBLY
(Click here)


20. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)
(Click here)


21. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)
(Click here)


22. INSTALL REAR SEAT ASSEMBLY (for Fold Down Seat Type)
(Click here)


23. INSTALL FRONT SEAT ASSEMBLY (for Driver Side)
(Click here)


24. INSTALL FRONT SEAT ASSEMBLY (for Front Passenger Side)
(Click here)


25. INSTALL SPARE WHEEL COVER
  1. Install the spare wheel cover.



26. INSTALL DECK BOARD ASSEMBLY
  1. Install the deck board.