Home › Power Source / Network · NETWORKING › LIN COMMUNICATION SYSTEM

DTC    B2325    LIN Communication Bus Malfunction

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) monitors communication between all the ECUs connected to the door bus lines. When the main body ECU (multiplex network body ECU) detects errors in communication with all the ECUs connected to the door bus lines at 2.6-second intervals and 3 times in a row, DTC B2325 will be stored.

DTC No.
DTC Detection Condition
Trouble Area
B2325
Main body ECU (multiplex network body ECU) detects errors in communication with the ECUs connected to the door bus lines 3 times in a row.
  1. Power window regulator motor assembly RH (for driver side)*1
  2. Power window regulator motor assembly LH (for driver side)*2
  3. Main body ECU (multiplex network body ECU)
  4. Instrument panel junction block assembly
  5. Harness or connector
  1. *1: for RHD
  2. *2: for LHD

WIRING DIAGRAM


E214075E06


INSPECTION PROCEDURE

NOTICE:
  1. When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization (Click here).
  2. When using the intelligent tester to troubleshoot with the ignition switch off:
    Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTCs (Click here).

Result 
Result
Proceed to
DTC B2325 is output
A
DTC B2325 is not output
B


B
USE SIMULATION METHOD TO CHECK (Click here)
A


3.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E229185E01
  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (Click here).

  1. Disconnect the 3B instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-12 - MB-16 (LIN2)
    Always
    Below 1 Ω
    3B-12 or MB-16 (LIN2) - Body ground
    Always
    10 kΩ or higher

Text in Illustration 
*a
Component without harness connected
(Instrument Panel Junction Block Assembly)


NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY)
  1. Disconnect the G3 power window regulator motor assembly RH (for driver side)*1 or H3 power window regulator motor assembly LH (for driver side)*2 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-12 - G3-9 (LIN)*1
    3B-12 - H3-9 (LIN)*2
    Always
    Below 1 Ω
    3B-12 or G3-9 (LIN) - Body ground*1
    3B-12 or H3-9 (LIN) - Body ground*2
    Always
    10 kΩ or higher

  1. *1: for RHD
  2. *2: for LHD


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)


    B157072E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G3-1 (GND) - Body ground*1
    H3-1 (GND) - Body ground*2
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G3-2 (B) - Body ground*1
    H3-2 (B) - Body ground*2
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Window Regulator Motor Assembly RH (for Driver Side))
    *a
    Front view of wire harness connector
    (to Power Window Regulator Motor Assembly LH (for Driver Side))

  1. *1: for RHD
  2. *2: for LHD


B
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
A


6.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY
  1. Replace the power window regulator motor assembly RH (for driver side)*1 or power window regulator motor assembly LH (for driver side)*2 (Click here).

    1. *1: for RHD
    2. *2: for LHD


NEXT


7.CLEAR DTC
  1. Check for DTCs (Click here).


NEXT


8.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B



B
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
A

END (POWER WINDOW REGULATOR MOTOR WAS DEFECTIVE)