Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM

DTC    C1277    Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)

DTC    C1278    Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)

DTC    C1415    Rear Speed Sensor RH Output Malfunction

DTC    C1416    Rear Speed Sensor LH Output Malfunction

for Preparation Click here


DESCRIPTION

Refer to DTCs C1403 and C1404 (Click here).

DTC No.
DTC Detection Condition
Trouble Area
C1415
C1416
Any of the following is detected:
  1. An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.
  2. At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.
  3. At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.
  1. Rear speed sensor RH/LH
  2. Speed sensor circuit
  3. Speed sensor rotor
  4. Skid control ECU (Brake actuator assembly)

Test Mode Diagnosis Code 
DTC No.
DTC Detection Condition
Trouble Area
C1277
C1278
Detected only during Test Mode.
  1. Rear speed sensor RH/LH
  2. Speed sensor rotor

HINT:
  1. DTC C1415 and C1277 are for the rear speed sensor RH.
  2. DTC C1416 and C1278 are for the rear speed sensor LH.


WIRING DIAGRAM

Refer to DTCs C1403 and C1404 .

INSPECTION PROCEDURE

NOTICE:
Disassembly of the rear speed sensor from the rear axle hub and bearing assembly is prohibited.

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Speed Open
    RR speed sensor open detection / Normal or Error
    Normal: Normal
    Error: Momentary interruption
    -
    RL Speed Open
    RL speed sensor open detection / Normal or Error
    Normal: Normal
    Error: Momentary interruption
    -

    OK:
    There are no momentary interruptions.

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 6
OK


2.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC (Skid Control ECU) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    RR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h
    When driving at constant speed: No large fluctuations
    RL Wheel Speed
    RL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h
    When driving at constant speed: No large fluctuations

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).

    NOTICE:
    Check the speed sensor signal after replacement (Click here).

    HINT:
    1. The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
      If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.
    2. If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
Go to step 5
OK


3.PERFORM TEST MODE (SIGNAL CHECK)
  1. Turn the ignition switch off.

  1. Perform the sensor check in the Test Mode procedure (Click here).

    OK:
    All Test Mode DTCs are cleared.



NG
Go to step 5
OK


4.RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

Result 
Result
Proceed to
DTCs C1415 and C1416 are not output
A
DTCs C1415 and/or C1416 are output
B

HINT:
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
Go to step 10
A

CHECK INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

5.CHECK REAR SPEED SENSOR INSTALLATION
  1. Turn the ignition switch off.



    C118693E02
  1. Check the speed sensor installation.

    OK:
    There is no clearance between the sensor and the rear axle hub.

    HINT:
    Because the rear axle hub and bearing assembly cannot be disassembled, if the rear speed sensor needs replacement, replace the rear axle hub and bearing assembly.

Text in Illustration 
*a
Normal
*b
Abnormal
*c
Clearance


NG
REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (REAR SPEED SENSOR, SENSOR ROTOR) (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (REAR SPEED SENSOR WIRE)
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control sensor wire connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (RH):
    Tester Connection
    Condition
    Specified Condition
    W1-2 (+) - WK1-1
    Always
    Below 1 Ω
    W1-1 (-) - WK1-2
    Always
    Below 1 Ω
    W1-2 (+) - WK1-2
    Always
    10 kΩ or higher
    W1-2 (+) - Body ground
    Always
    10 kΩ or higher
    W1-1 (-) - WK1-1
    Always
    10 kΩ or higher
    W1-1 (-) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (LH):
    Tester Connection
    Condition
    Specified Condition
    V1-2 (+) - VK1-1
    Always
    Below 1 Ω
    V1-1 (-) - VK1-2
    Always
    Below 1 Ω
    V1-2 (+) - VK1-2
    Always
    10 kΩ or higher
    V1-2 (+) - Body ground
    Always
    10 kΩ or higher
    V1-1 (-) - VK1-1
    Always
    10 kΩ or higher
    V1-1 (-) - Body ground
    Always
    10 kΩ or higher

    NOTICE:
    Check the speed sensor signal after replacement (Click here).

  1. Reconnect the skid control sensor wire connector.



NG
REPLACE REAR SPEED SENSOR WIRE
OK


7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU connector and the rear speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A55-17 (RR+) - W1-2 (+)
    Always
    Below 1 Ω
    A55-16 (RR-) - W1-1 (-)
    Always
    Below 1 Ω
    A55-5 (RL+) - V1-2 (+)
    Always
    Below 1 Ω
    A55-4 (RL-) - V1-1 (-)
    Always
    Below 1 Ω
    A55-17 (RR+) - Body ground
    Always
    10 kΩ or higher
    A55-16 (RR-) - Body ground
    Always
    10 kΩ or higher
    A55-5 (RL+) - Body ground
    Always
    10 kΩ or higher
    A55-4 (RL-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the skid control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT SKID CONTROL ECU (SENSOR INPUT)


    C233859E04
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage (RH):
    Tester Connection
    Switch Condition
    Specified Condition
    W1-2 (+) - Body ground
    Ignition switch ON
    8 to 14 V
    V1-2 (+) - Body ground
    Ignition switch ON
    8 to 14 V

    NOTICE:
    Check the speed sensor signal after replacement (Click here).

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).

Text in illustration 
*a
Front view of wire harness connector
(to Rear Speed Sensor)
  1. Reconnect the rear speed sensor connector.

Result 
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C


B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A


9.RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

Result 
Result
Proceed to
DTCs C1415 and/or C1416 are output
A
DTCs C1415 and C1416 are not output
B

HINT:
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
CHECK INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)
A


10.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (REAR SPEED SENSOR, SENSOR ROTOR)
  1. Turn the ignition switch off.

  1. Replace the rear speed sensor and rear axle hub and bearing assembly (Click here).

    NOTICE:
    Check the speed sensor signal after replacement (Click here).

    HINT:
    The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
    If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.


NEXT


11.RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

Result 
Result
Proceed to
DTCs C1415 and C1416 are not output
A
DTCs C1415 and/or C1416 are output (for LHD)
B
DTCs C1415 and/or C1416 are output (for RHD)
C

HINT:
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

END