DTC Table

Precautions: Precautions for Diagnosing Trouble · Precautions for Control Systems · General safety (00)

NOTE:

History DTC of the DTC with “*1” is not memorized.

DTC	DTC name	DTC detecting condition
B1120 (*1)	BCM Internal Defect	BCM internal failure.
B1127	Driving Mode Switch Circuit	Driving mode switch signal circuit voltage is not as specified for specified time continuously.
B1133	Battery Voltage too High	Backup power supply circuit voltage from “DOME” fuse is continuously higher than 16.0 V for specified time.
B1141	Outside Air Temperature (Ambient Temperature) Sensor Circuit Open	Outside air temperature sensor signal circuit voltage is higher than 4.85 V for specified time continuously.
B1142	Outside Air Temperature (Ambient Temperature) Sensor Circuit Short to Ground	Outside air temperature sensor signal circuit voltage is lower than 0.15 V for specified time continuously.
B1145	A/C Evaporator Temperature Sensor Circuit High	Evaporator temperature sensor signal circuit voltage is higher than 4.85 V for specified time continuously.
B1146	A/C Evaporator Temperature Sensor Circuit Low	Evaporator temperature sensor signal circuit voltage is lower than 0.15 V for specified time continuously.
B1150	Air Bag Communication Circuit Malfunction	After ignition “ON”, abnormal signal is fed from SDM to BCM.
B1157	Air Bag Deployment Signal Input	Air bag deployment signal is fed from SDM to BCM.
B115A	Driving Modes Mismatched	Inconsistency between driving mode request signal and actual driving mode signal transmitted via CAN communication for specified time continuously.
B1670 (*1)	Rain / Light Sensor Malfunction	BCM detected malfunction related to rain / light sensor.
B1680	CAN Invalid Data from ECM	BCM detected abnormal condition in control data transmitted by ECM through CAN communication.
B1682	CAN Invalid Data from 4WD Control Module	BCM detected abnormal condition in control data transmitted by 4WD control module through CAN communication.
B1683 (*1)	Yaw Rate Information Mismatched	Difference between target yaw rate calculated by BCM and actual yaw rate transmitted from ESP^® control module via CAN communication is continuously higher than specified value for specified time.
B1685 (*1)	CAN Invalid Data from ESP^® Control Module	BCM detected abnormal condition in control data transmitted by ESP^® control module through CAN communication.
B1687 (*1)	CAN Invalid Data from Lateral G Sensor	BCM detected abnormal condition in lateral G data transmitted by ESP^® control module through CAN communication.
B1688 (*1)	CAN Invalid Data from Yaw Rate Sensor	BCM detected abnormal condition in yaw rate data transmitted by ESP^® control module through CAN communication.
B1689 (*1)	CAN Invalid Data from Wheel Speed Sensor	BCM detected abnormal condition in wheel speed data transmitted by ESP^® control module through CAN communication.
B1690 (*1)	Steering Angle Sensor Malfunction	•Steering angle sensor malfunction is detected. •Incomplete calibration of steering angle sensor is detected.
B1691	CAN Invalid Data from Steering Angle Sensor	BCM received abnormal CAN communication data from steering angle sensor.
B1692	CAN Invalid Data from Steering Angle Sensor	BCM received abnormal CAN communication data from steering angle sensor.
B1695	CAN Invalid Data from ESP^® Control Module	BCM received abnormal CAN communication data from ESP^® control module.
B1696	CAN Invalid Data from ESP^® Control Module	BCM received abnormal CAN communication data from ESP^® control module.
U0073	Control Module Communication Bus Off	BCM fails to transmit and receive the data via CAN for specified time continuously.
U0100	Lost Communication With ECM	Receiving error of the data from ECM via CAN for specified time continuously.
U0101	Lost Communication With TCM	Receiving error of the data from TCM via CAN for specified time continuously.
U0114	Lost Communication With 4-Wheel Drive Control Module	Receiving error of the data from 4WD control module via CAN for specified time continuously.
U0121	Lost Communication With ABS / ESP^® Control Module	Receiving error of the data from ESP^® control module via CAN for specified time continuously.
U0126	Lost Communication With Steering Angle Sensor Module	Receiving error of the data from steering angle sensor via CAN for specified time continuously.
U0131	Lost Communication With Power Steering Control Module	Receiving error of the data from P/S control module via CAN for specified time continuously.
U0141	Lost Communication With Keyless Start Control Module	Receiving error of the data from keyless entry / keyless start control module via CAN for specified time continuously.
U0151	Lost Communication With Restraints Control Module	Receiving error of the data from SDM via CAN for specified time continuously.
U0155	Lost Communication With Instrument Panel Cluster (IPC) Control Module	Receiving error of the data from combination meter via CAN for specified time continuously.
U0164	Lost Communication With HVAC Control Module	Receiving error of the data from HVAC control module via CAN for specified time continuously.
U0231 (*1)	Lost Communication With Rain Sensing Module	Receiving error of the data from rain / light sensor via CAN for specified time continuously.
U1082	Lost Communication With ENG A-STOP Control Module	Receiving error of the data from ENG A-STOP control module via CAN for specified time continuously.