Scan Tool Data
Precautions: Precautions for Diagnosing Trouble · Precautions for Replacing Remote Controller · Precautions for Remote Controller Disposal · Precautions for Replacing Keyless Start Control Module · Precautions for Control Systems · General safety (00)
Keyless Start Control Module
NOTE:
•If communication between SUZUKI scan tool and keyless start control module is not possible, perform the following checks:
—Check communication condition between PC and VCI using SUZUKI scan tool function.
—Check DLC power circuit and ground circuit.
—Check DLC cable. If necessary, check DLC cable by substituting a known-good DLC cable.
—Check CAN communication system. (“Control Module Communication Bus Off” is detected in any control module.)
—Check keyless start control module power circuit and ground circuit.
•Some data in the table below may either be applicable or not applicable depending on the model.—Check DLC power circuit and ground circuit.
—Check DLC cable. If necessary, check DLC cable by substituting a known-good DLC cable.
—Check CAN communication system. (“Control Module Communication Bus Off” is detected in any control module.)
—Check keyless start control module power circuit and ground circuit.
| Scan tool data | Normal condition / Reference value | Condition |
|---|---|---|
| Battery Voltage | 10 – 14 V | Engine: Running |
| Vehicle Speed | Almost the same as speedometer reading | In driving |
| Engine Speed | M16A-M/T model: 550 – 650 rpm | Engine: Idle speed with no load applied after warming up |
| M16A-A/T model: 600 – 700 rpm | ||
| K14C-M/T model: 650 – 750 rpm | ||
| K14C-A/T model: 700 – 800 rpm | ||
| D16AA model: Approx. 800 rpm | ||
| Ignition Position | IG OFF | Ignition: “OFF” |
| ACC | Ignition: “ACC” | |
| IG ON | Ignition: “ON” | |
| Cranking | Engine: Cranking | |
| Unclear | Other than above condition | |
| Driv Door SW | Open | Driver door: Opened |
| Close | Other than above condition | |
| Pass Door SW | Open | Other than driver door: Opened |
| Close | Other than above condition | |
| Rear End Door Opener | ON | Rear end door opener switch: Pushed |
| OFF | Other than above condition | |
| Back Door/Trunk SW | ON | Rear end door: Opened |
| OFF | Other than above condition | |
| Ignition 1 Relay | ON | Ignition “ON” or engine at cranking |
| OFF | Other than above condition | |
| Ignition 2 Relay | ON | Ignition: “ON” |
| OFF | Other than above condition | |
| Accessory Relay | ON | Ignition: “ACC” and “ON” |
| OFF | Other than above condition | |
| Starting Motor Relay (Com) | ON | Engine: Cranking |
| OFF | Other than above condition | |
| Steering Lock Counter |
0 – 5,000 times | Steering lock operation times: 0 – 5,000 |
| 5,001 – 7,000 times | Steering lock operation times: 5,001 – 7,000 | |
| 7,001 – 10,000 times | Steering lock operation times: 7,001 – 10,000 | |
| 10,001 – 15,000 times | Steering lock operation times: 10,001 – 15,000 | |
| 15,001 – 50,000 times | Steering lock operation times: 15,001 – 50,000 | |
| 50,001 – 100,000 times | Steering lock operation times: 50,001 – 100,000 | |
| 100,001 – 200,000 times | Steering lock operation times: 100,001 – 200,000 | |
| Over 200,001 times | Steering lock operation times: Over 200,001 | |
| Door Key SW (Lock) | ON | Driver key cylinder: Lock position |
| OFF | Other than above condition | |
| Door Key SW (Unlock) | ON | Driver key cylinder: Unlock position |
| OFF | Other than above condition | |
| Driver Request SW | ON | Driver door request switch: ON |
| OFF | Other than above condition | |
| Passenger Request SW | ON | Passenger door request switch: ON |
| OFF | Other than above condition | |
| Rear door/trunk requ SW | ON | Rear end door request switch: ON |
| OFF | Other than above condition | |
| Hood Switch | ON | Hood: Opened |
| OFF | Other than above condition | |
| P Position / CPP 2 Switch | ON | Clutch pedal: Depressed (M/T model) Select lever: P range (A/T model / twin clutch system model) Select lever button: Released (A/T model / twin clutch system model) |
| OFF | Other than above condition | |
| Starting Motor Relay (Mon) | ON | Engine: Cranking |
| OFF | Other than above condition | |
| Clutch / Shift Switch | ON | Clutch pedal: Depressed (M/T model) Select lever: P or N range (A/T model) |
| OFF |
•Other than above condition (M/T model / A/T model)
•“OFF” is indicated all the time (twin clutch system model) |
|
| Brake light Switch | ON | Brake pedal: Depressed |
| OFF | Other than above condition | |
| Steering Unlock Condition | ON | Ignition: “ACC” and “ON” |
| OFF | Other than above condition | |
| Steering Lock Condition | ON | Set ignition “OFF” and open a door |
| OFF | Other than above condition | |
| Driver Door Lock SW | ON | Driver door lock: Lock position |
| OFF | Other than above condition | |
| Passenger Door Lock SW | ON | Passenger door lock: Lock position |
| OFF | Other than above condition | |
| Ignition Switch1 | ON | Ignition: “ON” |
| OFF | Other than above condition | |
| Ignition Switch2 | ON | Ignition: “ON” |
| OFF | Other than above condition | |
| Accessory Switch | ON | Ignition: “ACC” and “ON” |
| OFF | Other than above condition | |
| Push Switch1 | ON | Engine switch: Pushed |
| OFF | Other than above condition | |
| Push Switch2 | ON | Engine switch: Pushed |
| OFF | Other than above condition | |
| Keyless Start System | ON | Keyless start control system: Active |
| OFF | Keyless start control system: Disabled | |
| Remote Controller Battery Warning | Active | Remote controller battery warning setting: Active mode |
| Disabled | Remote controller battery warning setting: Disabled mode | |
| Security Alarm | Active | Security alarm setting: Active mode |
| Disabled | Security alarm setting: Disabled mode | |
| Answer-back (Outside Buzzer) | Active | Answer-back (outside buzzer) setting: Active mode |
| Disabled | Answer-back (outside buzzer) setting: Disabled mode | |
| Answer-back | Hazard | Answer-back setting: Hazard mode |
| Interior | Answer-back setting: Dome light mode | |
| Remote Controller Area Warning | Active | Remote controller area warning setting: Active mode |
| Disabled | Remote controller area warning setting: Disabled mode |