Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1268/68    Transfer "L4" Position Switch Circuit

for Preparation Click here


DESCRIPTION

After confirming that the transfer is in the L4 position, A-TRAC and DAC will be activated according to the vehicle conditions (Click here).

DTC No.
DTC Detection Condition
Trouble Area
C1268/68
The L4 signal input to the ECU does not match the L4 signal output from the ECM.
  1. 4WD control (L4) switch
  2. 4WD control (L4) switch circuit
  3. 4WD control ECU

WIRING DIAGRAM


C132923E03


INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).

1.INSPECT SKID CONTROL ECU (EXI4 TERMINAL)


    C121700E97
  1. Disconnect the skid control ECU connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S28-21 (EXI4) - Body ground
    4WD control (L4) switch ON (Transfer L4 position)
    Below 1.5 V
    S28-21 (EXI4) - Body ground
    4WD control (L4) switch OFF (Any transfer position except L4)
    8 to 14 V



NG
Go to step 4
OK


2.PERFORM TEST MODE (SIGNAL CHECK)
  1. Check if the test mode (signal check) DTC is detected.

    Result:

    Condition
    Proceed to
    Test mode (signal check) DTC is output
    A
    Test mode (signal check) DTC is not output (When troubleshooting in accordance with the DTC CHART.)
    B
    Test mode (signal check) DTC is not output (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE.)
    C



B
REPAIR OR REPLACE HARNESS OR CONNECTOR (L4 CIRCUIT)

C
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
A


3.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Check if the same DTC is detected (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


    Result:

    Condition
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID 

4.INSPECT 4WD CONTROL SWITCH (GND TERMINAL)


    B059092E12
  1. Disconnect the 4WD control (4WD) switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    F11-4 (GND) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


5.INSPECT 4WD CONTROL SWITCH
  1. Check the select high-low system (Click here) or the select 2-4 and high-low system (Click here).



NG
REPLACE 4WD CONTROL SWITCH
OK


6.INSPECT 4WD CONTROL ECU
  1. Check the select high-low system (Click here) or the select 2-4 and high-low system (Click here).



NG
REPLACE 4WD CONTROL ECU
OK


7.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - 4WD CONTROL SWITCH)


    I045763E06
  1. Disconnect the 4WD control ECU connector and 4WD control (L4) switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    F9-15 (LO) - F11-2 (LO)
    Below 1 Ω
    F9-15 (LO) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - 4WD CONTROL ECU)


    I045765E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    S28-21 (EXI4) - F9-24 (L4)
    Below 1 Ω
    S28-21 (EXI4) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ECM)


    I045573E04
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    S28-21 (EXI4) - E6-13 (L4)
    Below 1 Ω
    S28-21 (EXI4) - Body ground
    10 kΩ or higher


    Result:

    Condition
    Proceed to
    OK (When troubleshooting in accordance with the DTC CHART.)
    A
    OK (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE.)
    B
    NG
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

END