Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0230  Fuel Pump Primary Circuit  


DESCRIPTION

When a malfunction in the fuel pump circuit is detected, DTC P0230 is stored.

The fuel pump circuit consists of the ECM, fuel pump and fuel pump ECU (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump ECU. Based on the signal sent from the ECM, the fuel pump ECU adjusts the fuel pump operation speed between 3 settings. The fuel pump ECU also has a self-diagnosis function. Based on the fuel pump circuit condition, the fuel pump ECU outputs a diagnostic signal (DI) to the ECM, and the ECM determines if there is a malfunction in the fuel pump circuit.

DTC No. DTC Detection Condition Trouble Area
P0230 Either condition is met (1 trip detection logic):
·

When the fuel pump is operating:

·

Amount of remaining fuel is 17 L (18 US qts, 15 Imp. qts) or more.

·

DI terminal output is low.


·

When the fuel pump is not operating:

·

DI terminal output is high.



·

Open or short in fuel pump circuit

·

Fuel pump

·

Fuel pump ECU

·

ECM



MONITOR DESCRIPTION

To monitor the fuel pump circuit, the ECM checks the fuel pump control signal (FPC) and diagnostic signal (DI). The FPC voltage varies between approximately 0 V and approximately 12 V (duty signal). Based on the condition of the fuel pump ECU malfunction, the DI voltage varies between approximately 0 V and approximately 12 V. The ECM then compares the variance of the FPC voltage and DI voltage, and determines if the fuel pump circuit is malfunctioning. When the ECM determines that the fuel pump circuit is malfunctioning, a DTC is stored immediately.

WIRING DIAGRAM

A227132E03
1.115,0.448 1.406,0.604 0.292,0.156 10 false IGN 0.292,2.292 0.417,2.448 0.125,0.156 10 false 4 0.479,2.292 0.688,2.458 0.208,0.167 10 false 1C 0.292,4.073 0.417,4.229 0.125,0.156 10 false 1 1.25,2.292 1.375,2.448 0.125,0.156 10 false 3 1.25,4.073 1.375,4.229 0.125,0.156 10 false 1 0.479,4.073 0.688,4.24 0.208,0.167 10 false 1E 0.958,2.292 1.167,2.458 0.208,0.167 10 false 1C 0.958,4.073 1.167,4.24 0.208,0.167 10 false 1C 2.365,4.073 2.49,4.229 0.125,0.156 10 false 2 2.552,4.073 2.76,4.24 0.208,0.167 10 false 1D 2.552,2.292 2.76,2.458 0.208,0.167 10 false 1D 1.948,2.292 2.073,2.448 0.125,0.156 10 false 4 2.844,2.292 2.969,2.448 0.125,0.156 10 false 3 2.135,2.292 2.344,2.458 0.208,0.167 10 false 1D 1.135,4.25 2.594,4.427 1.458,0.177 10 false No. 1 Integration Relay 1.313,2.771 1.573,2.917 0.26,0.146 10 false IG2 0.635,3.427 0.896,3.573 0.26,0.146 10 false IG2 2.302,3.396 2.563,3.552 0.26,0.156 10 false EFI 2.896,2.708 3.271,3.031 0.375,0.323 10 false EFI MAIN 0.667,4.542 1,4.688 0.333,0.146 10 false P/I-B 1.167,6.083 1.375,6.24 0.208,0.156 10 false ST 0.823,7 1.302,7.188 0.479,0.188 10 false Battery 1.49,5.135 1.781,5.292 0.292,0.156 10 false F15 1.49,5.292 2.552,5.5 1.063,0.208 10 false Ignition Switch 1.125,4.969 1.385,5.125 0.26,0.156 10 false IG2 1.115,5.51 1.427,5.667 0.313,0.156 10 false AM2 1.104,4.74 1.219,4.906 0.115,0.167 10 false 6 1.104,5.75 1.219,5.917 0.115,0.167 10 false 7 2.677,0.167 2.781,0.323 0.104,0.156 10 false 2 3.448,0.167 3.552,0.323 0.104,0.156 10 false 1 2.677,0.625 2.781,0.781 0.104,0.156 10 false 5 3.448,0.625 3.552,0.781 0.104,0.156 10 false 3 2.854,1.115 3.333,1.281 0.479,0.167 10 false C/OPN 4.135,1.271 5.177,1.417 1.042,0.146 10 false Fuel Pump ECU 3.896,2.083 4.01,2.24 0.115,0.156 10 false 4 3.844,2.302 4.073,2.448 0.229,0.146 10 false Q8 3.896,3.25 4.01,3.406 0.115,0.156 10 false 3 3.99,4.135 4.104,4.292 0.115,0.156 10 false 1 3.844,3.458 4.073,3.604 0.229,0.146 10 false Q8 4.177,4.156 4.406,4.302 0.229,0.146 10 false Q9 4.729,4.135 4.844,4.292 0.115,0.156 10 false 2 4.917,4.156 5.146,4.302 0.229,0.146 10 false Q9 5.271,2.083 5.385,2.24 0.115,0.156 10 false 1 5.219,2.302 5.448,2.448 0.229,0.146 10 false Q8 5.281,3.25 5.396,3.406 0.115,0.156 10 false 2 5.229,3.469 5.458,3.615 0.229,0.146 10 false Q8 4.146,5.052 4.26,5.198 0.115,0.146 10 false 4 5.052,5.052 5.167,5.198 0.115,0.146 10 false 5 4.302,5.271 4.521,5.427 0.219,0.156 10 false B2 4.802,5.271 5.021,5.427 0.219,0.156 10 false E2 4.292,5.823 4.521,5.969 0.229,0.146 10 false Q5 4.292,5.969 5,6.156 0.708,0.188 10 false Fuel Pump 6.073,0.125 6.198,0.271 0.125,0.146 10 false 8 5.99,0.323 6.271,0.469 0.281,0.146 10 false F50 6.323,0.313 6.552,0.469 0.229,0.156 10 false FC 6.073,2.083 6.198,2.229 0.125,0.146 10 false 3 6,2.292 6.281,2.438 0.281,0.146 10 false F51 6.323,2.292 6.635,2.448 0.313,0.156 10 false FPC 6.042,3.26 6.229,3.406 0.188,0.146 10 false 26 6,3.469 6.281,3.615 0.281,0.146 10 false F50 6.323,3.458 6.552,3.615 0.229,0.156 10 false DI 6.073,4.427 6.198,4.573 0.125,0.146 10 false 9 6,4.646 6.281,4.792 0.281,0.146 10 false F51 6.323,4.615 6.75,4.771 0.427,0.156 10 false MREL 6.49,5.281 6.844,5.448 0.354,0.167 10 false ECM 4.146,2.26 4.375,2.417 0.229,0.156 10 false +B 4.854,2.292 5.156,2.448 0.302,0.156 10 false FPC 4.146,3.438 4.281,3.594 0.135,0.156 10 false E 4.979,3.469 5.156,3.625 0.177,0.156 10 false DI 4.188,3.948 4.417,4.104 0.229,0.156 10 false FP 4.885,3.948 5.146,4.104 0.26,0.156 10 false FP-

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


This troubleshooting procedure is based on the premise that the engine can be started. If the engine cannot be started, proceed to Problem Symptoms Table (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).

PROCEDURE

1.CHECK FOR DTC (B1500)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body Electrical / Combination Meter / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC B1500 is not output A
DTC B1500 is output B



A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL PUMP)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL PUMP)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


e.

Check whether operating sounds can be heard while operating the fuel pump using the intelligent tester.

OK:

Operating sounds can be heard from fuel pump.




OK

3.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM, BODY GROUND)

NG

6.INSPECT CIRCUIT OPENING RELAY (C/OPN)
3.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM, BODY GROUND)
a.

Disconnect the fuel pump ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q8-1 (FPC) - F51-3 (FPC) Always Below 1 Ω
Q8-2 (DI) - F50-26 (DI) Always Below 1 Ω
Q8-3 (E) - Body ground Always Below 1 Ω
Q8-1 (FPC) or F51-3 (FPC) - Body ground Always 10 kΩ or higher
Q8-2 (DI) or F50-26 (DI) - Body ground Always 10 kΩ or higher




OK

4.REPLACE FUEL PUMP ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE FUEL PUMP ECU
a.

Replace the fuel pump ECU (See page Engine / Hybrid System>1GR-FE FUEL>FUEL PUMP ECU>REMOVAL).



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS
5.CHECK WHETHER DTC OUTPUT RECURS
a.

Check that there are 17 liters (18 US qts, 15 Imp. qts) or more of fuel remaining.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.



f.

Crank the engine for 15 seconds.


g.

Idle the engine for 1 minute.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0230 is output B



A

END

B

6.INSPECT CIRCUIT OPENING RELAY (C/OPN)
a.

Inspect the circuit opening relay (C/OPN) (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION).



OK

7.INSPECT CIRCUIT OPENING RELAY (POWER SOURCE VOLTAGE)

NG

REPLACE CIRCUIT OPENING RELAY (C/OPN)

7.INSPECT CIRCUIT OPENING RELAY (POWER SOURCE VOLTAGE)
A227634E01
0.405,1.177 0.608,1.333 0.202,0.156 10 *1 2.262,0.209 2.464,0.365 0.202,0.156 10 *2

a.

Remove the circuit opening relay (C/OPN) from the engine room relay block.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Circuit opening relay (C/OPN) terminal 2 - Body ground Ignition switch ON 11 to 14 V
Circuit opening relay (C/OPN) terminal 5 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block
*2 Circuit Opening Relay (C/OPN)



OK

8.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY (C/OPN) - ECM, FUEL PUMP ECU)

NG

14.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY (C/OPN) - NO. 1 INTEGRATION RELAY)
8.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY (C/OPN) - ECM, FUEL PUMP ECU)
a.

Remove the circuit opening relay (C/OPN) from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Disconnect the fuel pump ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Circuit opening relay (C/OPN) terminal 1 - F50-8 (FC) Always Below 1 Ω
Circuit opening relay (C/OPN) terminal 3 - Q8-4 (+B) Always Below 1 Ω
Circuit opening relay (C/OPN) terminal 1 or F50-8 (FC) - Body ground Always 10 kΩ or higher
Circuit opening relay (C/OPN) terminal 3 or Q8-4 (+B) - Body ground Always 10 kΩ or higher




OK

9.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU)
a.

Disconnect the fuel pump connector.


b.

Disconnect the fuel pump ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q5-4 (B2) - Q9-1 (FP) Always Below 1 Ω
Q5-5 (E2) - Q9-2 (FP-) Always Below 1 Ω
Q5-4 (B2) or Q9-1 (FP) - Body ground Always 10 kΩ or higher
Q5-5 (E2) or Q9-2 (FP-) - Body ground Always 10 kΩ or higher




OK

10.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT FUEL PUMP
a.


OK

11.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM, BODY GROUND)

NG

11.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM, BODY GROUND)
a.

Disconnect the fuel pump ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q8-1 (FPC) - F51-3 (FPC) Always Below 1 Ω
Q8-2 (DI) - F50-26 (DI) Always Below 1 Ω
Q8-3 (E) - Body ground Always Below 1 Ω
Q8-1 (FPC) or F51-3 (FPC) - Body ground Always 10 kΩ or higher
Q8-2 (DI) or F50-26 (DI) - Body ground Always 10 kΩ or higher




OK

12.REPLACE FUEL PUMP ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE FUEL PUMP ECU
a.

Replace the fuel pump ECU (See page Engine / Hybrid System>1GR-FE FUEL>FUEL PUMP ECU>REMOVAL).



NEXT

13.CHECK WHETHER DTC OUTPUT RECURS
13.CHECK WHETHER DTC OUTPUT RECURS
a.

Check that there are 17 liters (18 US qts, 15 Imp. qts) or more of fuel remaining.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.



f.

Crank the engine for 15 seconds.


g.

Idle the engine for 1 minute.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0230 is output B



A

END

B

14.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY (C/OPN) - NO. 1 INTEGRATION RELAY)
a.

Remove the circuit opening relay (C/OPN) from the engine room relay block.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Disconnect the No. 1 integration relay connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Circuit opening relay (C/OPN) terminal 2 - 1C-4 Always Below 1 Ω
Circuit opening relay (C/OPN) terminal 5 - 1D-4 Always Below 1 Ω
Circuit opening relay (C/OPN) terminal 2 or 1C-4 - Body ground Always 10 kΩ or higher
Circuit opening relay (C/OPN) terminal 5 or 1D-4 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR