Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0137  Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)  P0157  Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2)  


DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric air-fuel level. For the purpose of helping the ECM to deliver accurate air-fuel ratio control, a heated oxygen sensor is used.

The heated oxygen sensor is located between the front and rear catalysts, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with a heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air-fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The heated oxygen sensor informs the ECM that the post-three-way catalytic converter air-fuel ratio is lean (low voltage, i.e. below 0.45 V).

Conversely, when the air-fuel ratio is richer than the stoichiometric air-fuel level, the oxygen concentration in the exhaust gas becomes lean. The heated oxygen sensor informs the ECM that the post-three-way catalytic converter air-fuel ratio is rich (high voltage, i.e. higher than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air-fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air-fuel ratio after the three-way catalytic converter is rich or lean and adjusts the fuel injection time accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in primary air-fuel ratio control.

A115539E07
2.979,1.229 3.292,0.844 false 2.688,1.792 3.302,1.792 true 2.594,2.417 3.25,2.385 true 2.677,2.698 3.26,2.833 false 1.094,2.917 1.333,2.917 false 2.667,1.458 2.667,1.531 false 2.729,1.646 3.302,1.271 3.302,1.271 2.667,1.49 true 1.448,0.771 2.458,0.969 1.01,0.198 10 false Atmospheric Air 3.354,0.74 4.094,0.938 0.74,0.198 10 false Housing 3.365,1.188 4.667,1.406 1.302,0.219 10 false Platinum Electrode 3.958,0.885 4.927,1.083 0.969,0.198 10 false Output Voltage 5.01,0.927 6.396,1.125 1.385,0.198 10 false Ideal Air-fuel Mixture 2.01,3.167 2.906,3.365 0.896,0.198 10 false Exhaust Gas 3.344,1.698 4.521,2.083 1.177,0.385 10 false Solid Electrolyte (Zirconia Element) 3.292,2.76 4.49,2.958 1.198,0.198 10 false Coating (Ceramic) 3.323,2.281 3.802,2.479 0.479,0.198 10 false Heater 1.365,2.823 1.802,3.031 0.438,0.208 10 false Cover 4.792,2.927 7.094,3.125 2.302,0.198 10 false Richer - Air-fuel Ratio - Leaner

DTC No. DTC Detection Condition Trouble Area
P0137
P0157
·

Low voltage (open):

During active air-fuel ratio control, conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) Heated oxygen sensor voltage output is below 0.21 V.


(b) Target air-fuel ratio is rich.



·

Open in heated oxygen sensor (for Bank 1, 2) circuit

·

Heated oxygen sensor (bank 1, 2 sensor 2)

·

Heated oxygen sensor heater (bank 1, 2 sensor 2)

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

No. 1 integration relay

·

Gas leak from exhaust system



MONITOR DESCRIPTION

Active Air-Fuel Ratio Control

The ECM usually performs air-fuel ratio feedback control so that the air fuel ratio sensor output indicates a near stoichiometric air-fuel level. This vehicle includes active air-fuel ratio control in addition to regular air-fuel ratio control. The ECM performs active air-fuel ratio control to detect any deterioration in the three-way catalytic converter and heated oxygen sensor malfunctions (refer to the diagram below).

Active air-fuel ratio control is performed for approximately 15 to 20 seconds while driving with a warm engine. During active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.


Open or Short in Heated Oxygen Sensor Circuit (DTC P0137 and P0157)

During active air-fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the three-way catalytic converter by forcibly regulating the air-fuel ratio to become rich or lean. If the heated oxygen sensor has an open or short, or the voltage output of the sensor decreases significantly, the OSC indicates an extraordinarily high value. Even if the ECM attempts to continue regulating the air-fuel ratio so that it becomes rich or lean, the heated oxygen sensor output does not change.

While performing active air-fuel ratio control, when the target air-fuel ratio is rich and the heated oxygen sensor voltage output is 0.21 V or less (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P0137 or P0157.

*: The TWC has the capability to store oxygen. The OSC and the emission purification capacity of the three-way catalytic converter are mutually related. The ECM determines whether the catalyst has deteriorated based on the calculated OSC value.

In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the Oxygen Storage Capacity (OSC) of the three-way catalytic converter. This calculation is based on the voltage output of the heated oxygen sensor while performing active air fuel ratio control.

The OSC value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 15 to 20 seconds.

When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the rich-lean cycle of the heated oxygen sensor is long, the OSC becomes greater. There is a direct correlation between the OSCs of the heated oxygen sensor and the three-way catalytic converter.

A229870E02
4.656,1.823 4.375,1.688 false 5.969,2.479 6.156,2.146 false 6,3.219 6.188,3.427 false 5.156,2.156 5.26,1.604 false 0.073,0.146 3.615,0.354 3.542,0.208 10 false HEATED OXYGEN SENSOR CIRCUIT LOW VOLTAGE 0.104,0.563 1.875,0.771 1.771,0.208 10 false (P0137 and P0157: OPEN) 0.792,1.333 2.823,1.531 2.031,0.198 10 false Active Air-Fuel Ratio Control 0.792,2.75 2.781,2.948 1.99,0.198 10 false Heated Oxygen Sensor Voltage 0.823,1.823 2.292,2.021 1.469,0.198 10 false Target Air-Fuel Ratio 2.552,1.885 3.51,2.24 0.958,0.354 10 false Stoichiometric Air-Fuel Level 3.198,1.51 3.458,1.708 0.26,0.198 10 false Off 3.01,2.927 3.469,3.125 0.458,0.198 10 false 0.21 V 4.604,0.5 5.906,0.698 1.302,0.198 10 false 15 to 20 seconds 4.5,1.448 5.26,1.646 0.76,0.198 10 false Operating 3.906,1.615 4.469,1.813 0.563,0.198 10 false Normal 5.302,1.438 6.042,1.635 0.74,0.198 10 false Abnormal 6.229,3.365 6.969,3.563 0.74,0.198 10 false Abnormal 6.208,2.052 6.771,2.25 0.563,0.198 10 false Normal 4.792,2.167 5.156,2.365 0.365,0.198 10 false Rich


WIRING DIAGRAM

A227125E01
0.563,5.32 1.052,5.504 0.489,0.184 10 Battery 0.432,3.35 0.792,3.515 0.360,0.165 10 P/I-B 0.531,0.419 0.659,0.584 0.128,0.165 10 1 0.488,0.613 0.718,0.778 0.230,0.165 10 1E 2.343,0.419 2.471,0.584 0.128,0.165 10 4 0.851,1.469 0.979,1.635 0.128,0.165 10 3 2.3,0.613 2.530,0.778 0.230,0.165 10 1D 2.343,0.857 2.471,1.022 0.128,0.165 10 2 2.3,1.05 2.530,1.215 0.230,0.165 10 1D 1.056,1.476 1.286,1.641 0.230,0.165 10 1D 0.974,0.762 1.250,0.927 0.276,0.165 10 EFI 1.515,1.379 2.162,1.544 0.647,0.165 10 EFI MAIN 1.203,1.706 2.655,1.908 1.452,0.202 10 No. 1 Integration Relay 2.748,0.762 3.395,0.946 0.647,0.184 10 EFI No. 2 3.839,0.51 3.958,0.675 0.119,0.165 10 2 3.839,1.285 3.958,1.451 0.119,0.165 10 4 4.855,0.51 4.973,0.675 0.119,0.165 10 1 4.855,1.285 4.973,1.451 0.119,0.165 10 3 4.028,0.505 4.258,0.670 0.230,0.165 10 +B 4.019,1.285 4.239,1.460 0.221,0.174 10 E2 4.43,0.491 4.808,0.647 0.378,0.156 10 HT1B 4.392,1.22 4.807,1.385 0.415,0.165 10 OX1B 3.596,3.16 3.715,3.325 0.119,0.165 10 2 3.596,3.935 3.715,4.101 0.119,0.165 10 4 4.612,3.16 4.731,3.325 0.119,0.165 10 1 4.612,3.935 4.731,4.101 0.119,0.165 10 3 3.785,3.155 4.015,3.320 0.230,0.165 10 +B 3.776,3.935 3.997,4.110 0.221,0.174 10 E2 4.187,3.142 4.565,3.297 0.378,0.156 10 HT2B 4.149,3.87 4.565,4.035 0.415,0.165 10 OX2B 3.664,1.584 3.959,1.749 0.295,0.165 10 B29 3.664,1.734 5.144,2.084 1.480,0.350 10 Heated Oxygen Sensor (for Bank 1 Sensor 2) 3.43,4.218 3.725,4.383 0.295,0.165 10 B30 3.43,4.368 4.910,4.718 1.480,0.350 10 Heated Oxygen Sensor (for Bank 2 Sensor 2) 6.307,5.984 6.657,6.167 0.350,0.184 10 ECM 5.691,0.422 5.884,0.597 0.193,0.174 10 12 5.999,0.517 6.405,0.682 0.406,0.165 10 HT1B 5.659,0.614 5.972,0.788 0.313,0.174 10 B39 5.737,1.207 5.884,1.381 0.147,0.174 10 2 5.999,1.388 6.405,1.553 0.406,0.165 10 OX1B 5.659,1.398 5.972,1.573 0.313,0.174 10 B36 5.747,2.477 5.884,2.651 0.137,0.174 10 1 5.999,2.658 6.405,2.824 0.406,0.165 10 EX1B 5.659,2.669 5.972,2.843 0.313,0.174 10 B36 5.691,3.065 5.884,3.240 0.193,0.174 10 13 5.999,3.16 6.405,3.325 0.406,0.165 10 HT2B 5.659,3.257 5.972,3.431 0.313,0.174 10 B39 5.737,3.841 5.884,4.015 0.147,0.174 10 4 5.999,4.022 6.405,4.187 0.406,0.165 10 OX2B 5.659,4.032 5.972,4.207 0.313,0.174 10 B36 5.747,5.018 5.884,5.192 0.137,0.174 10 3 5.999,5.199 6.405,5.364 0.406,0.165 10 EX2B 5.659,5.209 5.972,5.384 0.313,0.174 10 B36 5.747,5.466 5.884,5.640 0.137,0.174 10 9 5.999,5.555 6.405,5.720 0.406,0.165 10 MREL 5.659,5.657 5.972,5.832 0.313,0.174 10 F51 5.139,3.705 5.240,3.842 0.100,0.137 10 * 5.242,1.071 5.343,1.208 0.100,0.137 10 * 1.604,6.184 2.325,6.359 0.721,0.174 10 *: Shielded

CONFIRMATION DRIVING PATTERN

HINT:
·

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

·

Performing this confirmation pattern will activate the heated oxygen sensor monitor (the catalyst monitor is performed simultaneously). This is very useful for verifying the completion of a repair.



NOTICE:

This test will not be completed if the vehicle is driven under absolutely constant speed conditions, such as with cruise control activated.


A199376E01
1.988,2.392 2.229,2.573 0.241,0.182 10 [A] 2.597,2.086 2.808,2.275 0.211,0.188 10 [B] 3.942,0.642 4.158,0.830 0.216,0.188 10 [C] 4.996,3.303 5.219,3.496 0.223,0.193 10 [D] 0.379,0.436 1.595,0.620 1.216,0.184 10 120 km/h (75 mph) 0.434,1.305 1.562,1.489 1.128,0.184 10 60 km/h (40 mph) 1.186,2.151 1.585,2.316 0.399,0.165 10 Idling 0.468,2.326 1.663,2.486 1.195,0.160 10 Ignition Switch ON 2.312,2.859 3.120,3.043 0.809,0.184 10 Warming up 3.442,2.877 4.681,3.014 1.239,0.137 10 10 minutes or more

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the intelligent tester on [A].

6.

Start the engine and warm it up until the ECT reaches 75°C (167°F) or higher [B].

7.

With the transmission in 4th gear or higher, drive the vehicle at a speed between 60 and 120 km/h (40 and 75 mph) for 10 minutes or more [C].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0137 and P0157.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


UNKNOWN
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the judgment result shows INCOMPLETE or UNKNOWN, perform steps [C] and [D].



CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the intelligent tester.

1.

Connect the intelligent tester to the DLC3.

2.

Start the engine and turn the intelligent tester on.

3.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

4.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.

5.

Perform the Active Test with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

6.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the intelligent tester.



HINT:
·

The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



Tester Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio sensor)
+25% Rich Below 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio sensor)
-12.5% Lean Higher than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen sensor)
+25% Rich Higher than 0.55 V
O2S B1S2 or O2S B2S2
(Heated oxygen sensor)
-12.5% Lean Below 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


A283583E82
5.792,3.594 7.115,3.865 1.323,0.271 10 false - Air fuel ratio sensor 3.823,4.927 4.531,5.104 0.708,0.177 8 false Below 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 false Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 false Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 false Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 false Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 false Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 false Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 false Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 false Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 false Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 false Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 false Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 false Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 false Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 false Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 false Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 false Output Voltage 3.51,4.698 4.542,4.885 1.031,0.188 8 false Higher than 0.55 V 0.927,2.646 1.958,2.833 1.031,0.188 8 false Higher than 3.4 V 1.177,2.885 1.927,3.073 0.75,0.188 8 false Below 3.1 V 1.542,1.604 1.99,1.792 0.448,0.188 8 false +25% 1.49,1.833 1.917,2.01 0.427,0.177 8 false -12.5% 3.5,2.604 4.531,2.792 1.031,0.188 8 false Higher than 0.55 V 3.813,2.844 4.521,3.021 0.708,0.177 8 false Below 0.4 V 0.844,4.802 2.042,5.052 1.198,0.25 8 false Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 false Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 false Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 false Almost no reaction 0.917,6.771 1.948,6.958 1.031,0.188 8 false Higher than 3.4 V 1.167,7.021 1.917,7.208 0.75,0.188 8 false Below 3.1 V 0.24,2.083 0.396,2.281 0.156,0.198 10 false 1 0.24,4.25 0.396,4.448 0.156,0.198 10 false 2 0.25,6.333 0.406,6.531 0.156,0.198 10 false 3 0.24,8.417 0.396,8.615 0.156,0.198 10 false 4 0.115,0.49 0.49,0.719 0.375,0.229 10 false Case 0.813,0.448 2.844,0.844 2.031,0.396 10 false Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.375,0.469 5.531,0.875 2.156,0.406 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.938,0.469 6.979,0.885 1.042,0.417 10 false Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 false - 5.802,4 7.125,4.438 1.323,0.438 10 false - Air fuel ratio sensor heater 5.802,4.635 7.125,5.073 1.323,0.438 10 false - Air fuel ratio sensor circuit 5.844,5.51 6.896,5.885 1.052,0.375 10 false - Heated oxygen sensor 5.844,6.146 6.885,6.573 1.042,0.427 10 false - Heated oxygen sensor heater 5.844,6.75 6.885,7.188 1.042,0.438 10 false - Heated oxygen sensor circuit 5.823,7.51 6.708,7.917 0.885,0.406 10 false - Fuel injector assembly 5.813,8.063 6.969,8.396 1.156,0.333 10 false - Fuel pressure 5.802,8.375 7.094,9.083 1.292,0.708 10 false - Gas leak from exhaust system (Air fuel ratio extremely rich or lean) 2.552,2.75 3,2.938 0.448,0.188 8 false OK 2.5,4.719 2.948,4.906 0.448,0.188 8 false NG 2.552,6.865 3,7.052 0.448,0.188 8 false OK 2.5,8.844 2.948,9.031 0.448,0.188 8 false NG 5.167,2.708 5.615,2.896 0.448,0.188 8 false OK 5.167,4.813 5.615,5 0.448,0.188 8 false OK 5.135,8.854 5.583,9.042 0.448,0.188 8 false NG 5.135,6.771 5.583,6.958 0.448,0.188 8 false NG 1.479,3.688 1.927,3.875 0.448,0.188 8 false +25% 4.01,1.594 4.458,1.781 0.448,0.188 8 false +25% 4.063,3.667 4.51,3.854 0.448,0.188 8 false +25% 1.427,3.875 1.854,4.052 0.427,0.177 8 false -12.5% 4.021,1.823 4.448,2 0.427,0.177 8 false -12.5% 4.021,3.896 4.448,4.073 0.427,0.177 8 false -12.5% 1.427,5.76 1.875,5.948 0.448,0.188 8 false +25% 1.438,7.781 1.885,7.969 0.448,0.188 8 false +25% 4.083,7.792 4.531,7.979 0.448,0.188 8 false +25% 4.104,5.74 4.552,5.927 0.448,0.188 8 false +25% 1.406,5.948 1.833,6.125 0.427,0.177 8 false -12.5% 1.396,8.01 1.823,8.188 0.427,0.177 8 false -12.5% 4.031,8.021 4.458,8.198 0.427,0.177 8 false -12.5% 4.083,5.938 4.51,6.115 0.427,0.177 8 false -12.5%

·

Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leak.

OK:

No gas leak.




OK

2.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

2.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

OK

3.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN)

NG

3.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN)
a.

Inspect the No. 1 integration relay (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY

4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
U149610E03
2.646,0.552 1.896,1.177 false 2.74,2.75 1.979,3.385 false 0.125,0.052 0.323,0.25 0.198,0.198 10 false *a 0.125,2.292 0.323,2.49 0.198,0.198 10 false *b 2.708,0.417 2.927,0.604 0.219,0.188 10 false +B 2.792,2.646 3.01,2.833 0.219,0.188 10 false +B 0.531,1.302 0.823,1.469 0.292,0.167 10 false B29 0.531,3.469 0.823,3.635 0.292,0.167 10 false B30

a.

Disconnect the heated oxygen sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B29-2 (+B) - Body ground Ignition switch ON 11 to 14 V
B30-2 (+B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Heated Oxygen Sensor Bank 1)
*b Front view of wire harness connector
(to Heated Oxygen Sensor Bank 2)


d.

Turn the ignition switch off.


e.

Disconnect the ECM connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B29-1 (HT1B) - B39-12 (HT1B) Always Below 1 Ω
B29-3 (OX1B) - B36-2 (OX1B) Always Below 1 Ω
B29-4 (E2) - B36-1 (EX1B) Always Below 1 Ω
B30-1 (HT2B) - B39-13 (HT2B) Always Below 1 Ω
B30-3 (OX2B) - B36-4 (OX2B) Always Below 1 Ω
B30-4 (E2) - B36-3 (EX2B) Always Below 1 Ω
B29-1 (HT1B) or B39-12 (HT1B) - Body ground Always 10 kΩ or higher
B29-3 (OX1B) or B36-2 (OX1B) - Body ground Always 10 kΩ or higher
B30-1 (HT2B) or B39-13 (HT2B) - Body ground Always 10 kΩ or higher
B30-3 (OX2B) or B36-4 (OX2B) - Body ground Always 10 kΩ or higher



A137607E03
0.105,0.035 3.393,0.224 3.288,0.188 10 Reference (System Diagram of Bank 1 Sensor 2): 2.894,1.277 3.574,1.458 0.680,0.181 10 EFI No. 2 2.109,2.405 2.763,2.587 0.653,0.181 10 EFI MAIN 1.283,1.299 1.540,1.457 0.257,0.159 10 EFI 1.02,3.33 1.500,3.512 0.480,0.181 10 Ground 3.393,0.367 4.889,0.548 1.496,0.181 10 Heated Oxygen Sensor 3.438,0.976 3.663,1.158 0.226,0.181 10 +B 4.587,0.976 4.967,1.158 0.380,0.181 10 HT1B 3.444,1.547 3.702,1.729 0.258,0.181 10 E2 4.6,1.547 5.025,1.729 0.424,0.181 10 OX1B 5.217,1.547 5.641,1.729 0.424,0.181 10 OX1B 5.217,2.15 5.641,2.331 0.424,0.181 10 EX1B 3.893,0.801 4.329,0.982 0.436,0.181 10 Heater 3.879,1.404 4.338,1.585 0.459,0.181 10 Sensor 5.883,0.325 6.208,0.506 0.326,0.181 10 ECM 5.21,0.969 5.590,1.151 0.380,0.181 10 HT1B 5.21,2.693 5.613,2.874 0.403,0.181 10 MREL 0.485,1.002 0.977,1.363 0.492,0.360 10 from Battery


OK

5.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE HEATED OXYGEN SENSOR
a.


NEXT

6.PERFORM CONFIRMATION DRIVING PATTERN (DTC P0137 OR P0157)
6.PERFORM CONFIRMATION DRIVING PATTERN (DTC P0137 OR P0157)
HINT:

Refer to Confirmation Driving Pattern.



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


e.

Input the DTC: P0137 or P0157.


f.

Check that DTC MONITOR is NORMAL. If DTC MONITOR is INCOMPLETE, perform the driving pattern but increase the vehicle speed.

Result
Display (DTC Output) Proceed to
NORMAL
(No DTC output)
A
ABNORMAL
(P0137 or P0157 detected)
B



A

END

B