Home › Engine / Hybrid System › 1GR-FE INTAKE / EXHAUST › EXHAUST MANIFOLD › 2009.08–2014.08
RM1440E _51 Engine / Hybrid System _056128 1GR-FE INTAKE / EXHAUST _0273907 EXHAUST MANIFOLD A

1GR-FE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 89467B 1.INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

Hide 17105 2.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

a.
A388857E01
1.5,0.927 1.667,0.927 1.667,0.927 1.958,1.156 true 1.323,0.854 1.49,1.052 0.167,0.198 10 false *1

Install a new gasket onto the cylinder head.

Text in Illustration
*1 Protrusion
V100135

Front

NOTICE:

Be careful of the installation direction.



b.

Temporarily install the manifold with 6 new nuts.


c.
A388858E01
0.375,0.219 0.531,0.417 0.156,0.198 10 false 1 1.615,0.271 1.771,0.469 0.156,0.198 10 false 2 2.438,0.365 2.594,0.563 0.156,0.198 10 false 3 2.26,1.552 2.417,1.75 0.156,0.198 10 false 4 1.5,1.677 1.656,1.875 0.156,0.198 10 false 5 0.521,1.531 0.677,1.729 0.156,0.198 10 false 6

Tighten the 6 nuts in the sequence shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Connect the air fuel ratio sensor connector.


Hide 17168 3.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the heat insulator with the 3 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 17118 4.INSTALL MANIFOLD STAY

a.

Install the manifold stay with the 3 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 89467B 5.INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

Hide 17104 6.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

a.
A388869E01
0.521,1.021 0.823,0.635 0.823,0.635 1.094,0.635 true 1.115,0.542 1.427,0.74 0.313,0.198 10 false *1

Install a new gasket onto the cylinder head.

Text in Illustration
*1 Protrusion
V100135

Front

NOTICE:

Be careful of the installation direction.



b.

Temporarily install the manifold with 6 new nuts.


c.
A388870E01
1.667,0.271 1.823,0.469 0.156,0.198 10 false 1 2.5,0.229 2.656,0.427 0.156,0.198 10 false 2 3.135,1.49 3.292,1.688 0.156,0.198 10 false 3 2.563,1.802 2.719,2 0.156,0.198 10 false 4 1.948,1.74 2.104,1.938 0.156,0.198 10 false 5 1.302,1.771 1.458,1.969 0.156,0.198 10 false 6

Tighten the 6 nuts in the sequence shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Connect the air fuel ratio sensor connector.


Hide 17167 7.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the heat insulator with the 3 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 17119 8.INSTALL NO. 2 MANIFOLD STAY

a.

Install the manifold stay with the 3 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 17410 9.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Hide 53737B 15.INSTALL FRONT FENDER APRON SEAL LH

a.

w/ KDSS:

Install the apron seal with the 7 clips.


b.

w/o KDSS:

Install the apron seal with the 4 clips.


Hide 53736 16.INSTALL FRONT FENDER APRON SEAL RH

a.

Install the apron seal with the 5 clips.


Hide 53737A 17.INSTALL FRONT NO. 1 FENDER APRON TO FRAME SEAL LH

a.

Install the frame seal with the 5 clips.


Hide 53736B 18.INSTALL FRONT NO. 1 FENDER APRON TO FRAME SEAL RH

a.

Install the frame seal with the 5 clips.