1.REMOVE ENGINE ASSEMBLY
Remove the engine assembly (See page Engine / Hybrid System>1GR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL).
19500
2.REMOVE IGNITION COIL ASSEMBLY
11452
3.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
Remove the dipstick.
Remove the bolt and dipstick guide.
Remove the O-ring from the dipstick guide.
16206
4.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY
Disconnect the 2 hoses.
Remove the 3 bolts and water by-pass pipe.
16323
5.REMOVE WATER INLET HOUSING
Disconnect the 3 water by-pass hoses.
Remove the 5 bolts and water inlet housing.
Remove the O-ring and gasket from the water outlet pipe and water pump.
Remove the 3 water by-pass hoses.
16603A
6.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
Remove the bolt and No. 1 idler pulley.
16604
7.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY
16620
8.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
Remove the 5 bolts and V-ribbed belt tensioner.
15671
9.REMOVE OIL FILTER BRACKET
Remove the 2 nuts, bolt, oil filter bracket and gasket.
13471
10.REMOVE CRANKSHAFT PULLEY
Using SST, hold the crankshaft pulley and loosen the pulley bolt. Continue to loosen the bolt until only 2 or 3 threads are screwed into the crankshaft.
Using the pulley set bolt and SST, remove the crankshaft pulley and pulley bolt.
15771
11.REMOVE NO. 1 OIL PIPE
Remove the 2 oil pipe unions, oil control valve filter LH, 3 gaskets and No. 1 oil pipe.
Do not touch the mesh when removing the oil control valve filter.
15772
12.REMOVE NO. 2 OIL PIPE
Remove the 2 oil pipe unions, oil control valve filter RH, 3 gaskets and No. 2 oil pipe.
Do not touch the mesh when removing the oil control valve filter.
11181A
13.REMOVE REAR CYLINDER HEAD COVER
14.DISCONNECT FUEL PIPE SUB-ASSEMBLY
Remove the 2 bolts and disconnect the fuel pipe.
11202
15.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
Remove the 12 bolts, seal washer, cylinder head cover and gasket.
Make sure the removed parts are returned to the same places they were removed from.
Remove the 3 gaskets.
11201
16.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Remove the 12 bolts, seal washer, cylinder head cover and gasket.
Make sure the removed parts are returned to the same places they were removed from.
Remove the 3 gaskets.
12102A
17.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
Remove the 10 bolts and 2 nuts.
Make sure the removed parts are returned to the same places they were removed from.
Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.
| *1 | Oil Pan Seal Cutter |
Be careful not to damage the contact surfaces of the oil pans.
15104
18.REMOVE OIL STRAINER SUB-ASSEMBLY
Remove the 2 nuts, oil strainer and gasket.
12101
19.REMOVE OIL PAN SUB-ASSEMBLY
Remove the 17 bolts and 2 nuts.
Make sure the removed parts are returned to the same places they were removed from.
Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block as shown in the illustration.
| *1 | LH Side |
| *2 | RH Side |
| *a | Pry |
Tape the screwdriver tip before use.
Be careful not to damage the contact surfaces of the cylinder block and oil pan.
Remove the 3 O-rings from the timing chain cover.
11302
20.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
Remove the 26 bolts and the 2 nuts.
Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.
Tape the screwdriver tip before use.
Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.
Remove the oil pump gasket from the cylinder block.
11301C
21.REMOVE FRONT CRANKSHAFT OIL SEAL
Using a screwdriver and wooden block, pry out the oil seal.
Tape the screwdriver tip before use.
Do not damage the surface of the oil seal press fit hole.