Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › 2009.08–2013.08
RM1440E _51 Engine / Hybrid System _056125 1GR-FE ENGINE MECHANICAL _0273883 ENGINE ASSEMBLY A

1GR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53301 4.REMOVE HOOD SUB-ASSEMBLY

a.

Disconnect the washer nozzle hose.


b.
A225432

Remove the 8 bolts and hood.

NOTICE:

If the hood support is detached from the ball joint, it become non-reusable. Therefore, do not detach the hood support from the ball joint unless replacing it.



Hide 55781E 5.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Remove the cowl top ventilator louver (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL).


Hide 52129B 6.REMOVE FRONT BUMPER COVER LOWER

a.

Remove the clip, 5 bolts and front bumper cover lower.


Hide 51405A 7.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

a.

Remove the 4 bolts.


b.
A224743

Unhook the engine under cover from the vehicle body as shown in the illustration.


Hide 51495 8.REMOVE TRANSMISSION UNDER COVER

a.

Remove the 2 bolts and transmission under cover.


Hide 51450 9.REMOVE REAR ENGINE UNDER COVER ASSEMBLY

a.

Remove the 4 bolts and rear engine under cover.


Hide 53737B 10.REMOVE FRONT FENDER APRON SEAL LH

a.

Remove the 5 clips and front fender apron seal.


Hide 53736 11.REMOVE FRONT FENDER APRON SEAL RH

a.

Remove the 5 clips and front fender apron seal.


Hide 53737A 12.REMOVE NO. 1 FRONT FENDER APRON TO FRAME SEAL LH

a.

Remove the 5 clips and No. 1 front fender apron to frame seal.


Hide 53736B 13.REMOVE NO. 1 FRONT FENDER APRON TO FRAME SEAL RH

a.

Remove the 5 clips and No. 1 front fender apron to frame seal.


Hide 53292A 14.REMOVE UPPER RADIATOR SUPPORT SEAL

a.

Remove the 13 clips and upper radiator support seal.


Hide 28800A 17.DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL

Hide 28800 19.REMOVE BATTERY

Hide 74431 20.REMOVE BATTERY TRAY

Hide 52119A 22.REMOVE FRONT BUMPER COVER

a.

Remove the front bumper cover (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>REMOVAL).


Hide 24.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.

Remove the air cleaner filter element.


b.
A224715

Detach the wire harness clamp.


c.

Remove the 3 bolts and air cleaner case.


Hide 52521 25.REMOVE UPPER FRONT BUMPER RETAINER

Hide 53293C 26.REMOVE RADIATOR SIDE DEFLECTOR RH

Hide 53294C 27.REMOVE RADIATOR SIDE DEFLECTOR LH

Hide 16571C 28.REMOVE NO. 1 RADIATOR HOSE

Hide 16572D 29.REMOVE NO. 2 RADIATOR HOSE

Hide 16470 30.REMOVE RADIATOR RESERVOIR

Hide 32907C 31.DISCONNECT OIL COOLER TUBE

Hide 16400 33.REMOVE RADIATOR ASSEMBLY

Hide 44320 36.DISCONNECT VANE PUMP ASSEMBLY

Hide 88703 37.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 88704 38.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88320 39.REMOVE COOLER COMPRESSOR ASSEMBLY

Hide 17410 40.REMOVE FRONT EXHAUST PIPE ASSEMBLY

a.

Hide 17167 42.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17104 43.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 17168 45.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17105 46.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH

Hide 82715 47.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 11363A 51.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 82121 52.DISCONNECT ENGINE WIRE

a.
A222166

Remove the bolt and disconnect the connector.


b.
A222168

for 4WD:

Disconnect the connector and detach the clamp.


c.

d.

Disconnect the ECM connector.

i.
A227938

Detach the clamp and disconnect the 6 connectors.


ii.
A223850

Detach the grommet from the wire harness support.


iii.
A223851

Detach the 4 claws to remove the wire harness support from the vehicle, and then pull out the ECM connector to remove it from the vehicle.



Hide 53.DISCONNECT HEATER WATER HOSE ASSEMBLY

a.
A225434

Disconnect the 2 hoses and heater water hose.


Hide 23801P 54.DISCONNECT NO. 1 AND NO. 2 FUEL PIPES

a.
A222167

Remove the No. 2 fuel pipe clamp from the fuel tube connector.


b.

Disconnect the No. 1 and No. 2 fuel pipes (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 55.REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)

Hide 35000 58.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

a.

for 2WD:

Remove the automatic transmission from the vehicle (See page Drivetrain>A750E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION ASSEMBLY>REMOVAL).


b.

for 4WD:

Remove the automatic transmission from the vehicle (See page Drivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION ASSEMBLY>REMOVAL).


Hide 12371 59.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR (for 2WD)

Hide 12371 60.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR (for 4WD)

Hide 88704 61.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

a.
A224794

Remove the bolt and disconnect the suction hose.


Hide 62.DISCONNECT OIL COOLER TUBE SUB-ASSEMBLY

a.
A225666E02
0.344,0.115 0.583,0.313 0.24,0.198 10 false *A 0.344,1.115 0.583,1.313 0.24,0.198 10 false *B

Remove the bolt and disconnect the oil cooler tube.

Text in Illustration
*A w/o Air Cooled Transmission Oil Cooler
*B w/ Air Cooled Transmission Oil Cooler


Hide 32101 63.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A224775E08
1.427,0.354 1.635,0.135 1.635,0.135 2.74,0.135 true 2,0.448 2.313,0.135 false 2.792,0.073 3.26,0.323 0.469,0.25 10 true SST

Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.
A224777

Remove the 8 bolts, rear spacer, drive plate and front spacer.


Hide 64.REMOVE ENGINE ASSEMBLY

a.
U147659E07
2.979,0.448 2.896,0.448 2.896,0.448 2.74,0.667 false 0.354,0.677 0.563,0.677 0.563,0.677 0.792,0.885 true 0.188,0.594 0.354,0.771 0.167,0.177 10 false *1 3.021,0.375 3.208,0.552 0.188,0.177 10 false *2 3.094,1.771 3.198,1.938 0.104,0.167 10 false 1 2.406,1.948 2.51,2.115 0.104,0.167 10 false 2 1.198,1.813 1.302,1.979 0.104,0.167 10 false 1 0.458,1.719 0.563,1.885 0.104,0.167 10 false 2

Install 2 engine hangers with 4 bolts as shown in the illustration.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)

Text in Illustration
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger

HINT:
No. 1 Engine Hanger 12281-31110
No. 2 Engine Hanger 12282-31140
Bolt 91671-C0830



b.

Attach an engine sling device and hang the engine with a chain block.


c.
A225433

Remove the 6 nuts from the front engine mounting insulator LH and RH.


d.

Lift the engine out of the vehicle carefully.

NOTICE:

Make sure the engine is clear of all wiring and hoses.



e.

Remove the front engine mounting insulator LH and RH.


f.

Place the engine onto a work bench.


Hide 65.INSTALL ENGINE STAND

a.

Install the engine onto an engine stand with bolts.