Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM
RM1440E _51 Engine / Hybrid System _056132 CRUISE CONTROL _0273923 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

This circuit sends a signal to the ECM depending on the cruise control switch condition. The battery supplies positive (+) battery voltage to the cruise control switch. Terminal 11 (CCS) of the ECM receives the voltage which varies according to the switch condition.

WIRING DIAGRAM

E200577E05
6.46,1.275 6.796,1.417 0.336,0.142 10 F50 6.407,0.613 6.744,0.755 0.336,0.142 10 CCS 6.146,0.524 6.330,0.666 0.184,0.142 10 11 3.89,0.524 4.074,0.666 0.184,0.142 10 3 3.89,1.575 4.074,1.717 0.184,0.142 10 1 6.46,1.415 6.796,1.557 0.336,0.142 10 ECM 4.974,2.14 5.873,2.453 0.899,0.313 10 Spiral Cable Sub-assembly 5.619,0.618 5.888,0.757 0.269,0.139 10 F23 5.619,1.676 5.888,1.814 0.269,0.139 10 F23 5.704,1.508 5.801,1.649 0.097,0.141 10 2 5.704,0.443 5.801,0.584 0.097,0.141 10 1 4.936,0.618 5.105,0.757 0.169,0.139 10 z9 4.936,1.679 5.105,1.818 0.169,0.139 10 z9 4.974,1.508 5.071,1.649 0.097,0.141 10 4 4.974,0.443 5.071,0.584 0.097,0.141 10 3 5.221,0.541 5.536,0.681 0.314,0.140 10 CCS 5.221,1.598 5.536,1.739 0.314,0.140 10 ECC 3.503,0.541 3.817,0.681 0.314,0.140 10 CCS 3.503,1.598 3.817,1.739 0.314,0.140 10 ECC 3.946,1.953 4.852,2.267 0.906,0.313 10 Cruise Control Switch Wire 1.315,2.294 2.702,2.436 1.387,0.142 10 Cruise Control Switch 1.315,2.154 1.586,2.296 0.272,0.142 10 A 3.201,1.131 3.788,1.273 0.586,0.142 10 ON-OFF 1.643,1.136 2.002,1.283 0.360,0.147 10 -SET 2.465,1.131 2.857,1.273 0.392,0.142 10 +RES 0.837,1.136 1.436,1.273 0.599,0.137 10 CANCEL

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Use the Data List to check if the cruise control switch is functioning properly (See page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

Cruise Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Main SW M-CPU Cruise control switch (Main CPU) / ON or OFF ON: Cruise control switch on
OFF: Cruise control switch off
-
Cancel Switch CANCEL switch signal / ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch -SET switch signal / ON or OFF ON: -SET switch on
OFF: -SET switch off
-
RES/ACC Switch +RES switch signal / ON or OFF ON: +RES switch on
OFF: +RES switch off
-

OK:

On screen, each item changes between ON and OFF according to above chart.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY
2.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).


b.
E176804E05
2.064,1.153 2.380,1.295 0.316,0.142 10 CCS 1.606,1.153 1.922,1.295 0.316,0.142 10 ECC 2.258,1.145 2.083,0.875 false 1.803,1.145 1.978,0.875 false 0.733,4.264 1.049,4.406 0.316,0.142 10 CCS 1.188,4.264 1.504,4.406 0.316,0.142 10 ECC 1.362,4.256 1.187,3.922 false 0.917,4.256 1.091,3.922 false

If there are any defects as follows, replace the spiral cable with a new one: scratches, cracks, dents or chips on the connector or spiral cable.


c.

Check the spiral cable.

i.

Set the spiral cable to the center position (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).


ii.

Rotate the spiral cable 2.5 times clockwise and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable 5 times counterclockwise and measure the resistance according to the value(s) in the table below.

NOTICE:

As the spiral cable may break, do not rotate the spiral cable more than the specified amount.


Standard Resistance:
Tester Connection Condition Specified Condition
3 (CCS) - 1 (CCS) Always Below 1 Ω
4 (ECC) - 2 (ECC)



iii.

Set the spiral cable to the center position and rotate the spiral cable 2.5 times clockwise. Then, while rotating the spiral cable 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CCS) - 1 (CCS) Always Below 1 Ω
4 (ECC) - 2 (ECC)





OK

3.INSPECT CRUISE CONTROL SWITCH WIRE

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

3.INSPECT CRUISE CONTROL SWITCH WIRE
a.
U181019E01
0.601,3.161 0.915,3.301 0.314,0.140 10 ECC 1.461,3.161 1.775,3.301 0.314,0.140 10 CCS 1.275,1.414 1.589,1.554 0.314,0.140 10 ECC 0.764,1.396 1.078,1.537 0.314,0.140 10 CCS 1.394,2.692 1.643,3.146 false 1.038,2.692 0.79,3.146 false 1.271,1.125 1.451,1.397 false 1.103,1.125 0.947,1.38 false 1.105,0.117 1.278,0.263 0.173,0.145 10 z9 1.177,1.741 1.288,1.887 0.111,0.145 10 A

Disconnect the z9 spiral cable connector.


b.

Disconnect the A switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z9-3 (CCS) - A-3 (CCS) Always Below 1 Ω
z9-4 (ECC) - A-1 (ECC)
z9-3 (CCS) - Body ground Always 10 kΩ or higher
z9-4 (ECC) - Body ground




OK

4.INSPECT CRUISE CONTROL SWITCH

NG

REPLACE CRUISE CONTROL SWITCH WIRE

4.INSPECT CRUISE CONTROL SWITCH
a.

Remove the cruise control switch (See page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL).

B215369E02
0.497,2.805 0.807,2.986 0.310,0.181 10 CCS 1.384,2.78 1.694,2.961 0.310,0.181 10 ECC 2.573,2.725 2.976,2.907 0.403,0.181 10 (CCS) 2.573,2.046 2.976,2.227 0.403,0.181 10 (ECC) 0.934,2.401 0.665,2.777 false 1.314,2.401 1.53,2.746 false 3.866,2.385 4.230,2.567 0.364,0.181 10 MAIN 4.528,2.385 4.911,2.567 0.384,0.181 10 +RES 5.289,2.385 5.622,2.567 0.333,0.181 10 -SET 6,2.385 6.581,2.567 0.580,0.181 10 CANCEL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (CCS) - 1 (ECC) Cruise control switch on Below 2.5 Ω
Cruise control switch off 1 MΩ or higher
+RES switch held on 235 to 245 Ω
-SET switch held on 617 to 643 Ω
CANCEL switch held on 1509 to 1571 Ω




OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
a.

Disconnect the F23 spiral cable connector.


b.

Disconnect the F50 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F23-1 (CCS) - F50-11 (CCS) Always Below 1 Ω
F23-2 (ECC) - Body ground
F23-1 (CCS) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR