Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2009.08–2010.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

If any of the following is detected, the ABS warning light remains on.

·

The skid control ECU connector is disconnected from the skid control ECU.

·

There is a malfunction in the skid control ECU internal circuit.

·

There is an open in the harness between the combination meter and skid control ECU.

·

The anti-lock brake system is defective.

·

The voltage at terminal IG1 is high.

·

The rear differential is locked.*


*: w/ Rear Differential Lock

HINT:

It may not be possible to use the intelligent tester when the skid control ECU is abnormal.


WIRING DIAGRAM

C219843E02
5.396,0.833 5.667,1.031 0.271,0.198 10 false A6 5.74,0.844 6.063,1.063 0.323,0.219 10 false IG1 5.417,0.656 5.646,0.833 0.229,0.177 10 false 46 3.406,1 4.333,1.188 0.927,0.188 10 false ECU-IG NO. 1 2.083,0.833 3.146,1.104 1.063,0.271 10 false from IG1 Circuit 5.396,1.313 5.625,1.51 0.229,0.198 10 false A6 5.396,1.792 5.656,1.99 0.26,0.198 10 false A6 5.396,2.26 5.656,2.469 0.26,0.208 10 false A7 5.438,1.125 5.583,1.281 0.146,0.156 10 false 1 5.719,1.313 6.188,1.531 0.469,0.219 10 false GND1 5.729,1.802 6.156,1.958 0.427,0.156 10 false GND2 5.729,2.26 6.188,2.5 0.458,0.24 10 false GND3 5.417,1.604 5.708,1.823 0.292,0.219 10 false 32 5.438,2.083 5.635,2.281 0.198,0.198 10 false 4 5.396,2.938 5.646,3.115 0.25,0.177 10 false A6 5.406,2.75 5.646,2.938 0.24,0.188 10 false 40 5.74,2.938 6.25,3.156 0.51,0.219 10 false EXI3*1 2.281,3.26 2.573,3.427 0.292,0.167 10 false F47 2.281,3.448 4.625,3.729 2.344,0.281 10 false Four Wheel Drive Control ECU*1 3.75,2.844 3.948,3.01 0.198,0.167 10 false 15 3.375,2.854 3.677,3.052 0.302,0.198 10 false RLP 2.969,2.208 3.167,2.396 0.198,0.188 10 false IG 5.396,4.188 5.656,4.385 0.26,0.198 10 false A6 5.417,3.99 5.604,4.135 0.188,0.146 10 false 40 5.719,4.188 6.26,4.427 0.542,0.24 10 false EXI3*2 3.729,4.177 4.802,4.469 1.073,0.292 10 false from IG1 Circuit 5.417,4.813 7.021,5.188 1.604,0.375 10 false Master Cylinder Solenoid (Skid Control ECU) 0.885,4.771 2.875,5 1.99,0.229 10 false : CAN Communication System 0.458,3.76 0.896,3.99 0.438,0.229 10 false F14 0.448,3.958 1.865,4.177 1.417,0.219 10 false Combination Meter 0.99,3.198 1.396,3.406 0.406,0.208 10 false ABS 0.26,5.083 1.135,5.271 0.875,0.188 10 false *1: for 4WD 0.26,5.375 1.073,5.563 0.813,0.188 10 false *2: for 2WD

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK THAT SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check the skid control ECU connector connection.

OK:

The 2 connectors are securely connected.




OK

2.CHECK FOR DTC

NG

CONNECT CONNECTOR TO ECU CORRECTLY

2.CHECK FOR DTC
a.

Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

3.CHECK CAN COMMUNICATION LINE

B

3.CHECK CAN COMMUNICATION LINE
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

OK:

CAN Bus Check indicates no malfunctions in CAN communication.




OK

4.READ VALUE USING INTELLIGENT TESTER (IG1 VOLTAGE VALUE)

NG

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

4.READ VALUE USING INTELLIGENT TESTER (IG1 VOLTAGE VALUE)

OK

5.CHECK TERMINAL VOLTAGE (EXI3)

NG

7.CHECK TERMINAL VOLTAGE (IG1)
5.CHECK TERMINAL VOLTAGE (EXI3)
a.

Disconnect the A6 skid control ECU connector.


b.
U150101E01
0.097,0.113 0.359,0.266 0.262,0.153 10 *a 2.624,0.422 2.972,0.594 0.348,0.172 10 EXI3 2.595,0.505 2.522,0.505 2.522,0.505 2.02,1.502 false 0.207,0.741 0.432,0.911 0.225,0.170 10 A6

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A6-40 (EXI3) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)

Result
Result Proceed to
OK A
NG (for 4WD) B
NG (for 2WD) C



A

6.READ VALUE USING INTELLIGENT TESTER (ABS WARNING LIGHT)

B

9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI3 CIRCUIT)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.READ VALUE USING INTELLIGENT TESTER (ABS WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light/ ON or OFF OFF -

f.

When performing the ABS Warning Light Active Test, check ABS Warning Light in the Data List (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).


ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
ABS Warning Light ABS warning light Warning light ON/OFF Observe the combination meter.

Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Does not change between ON and OFF A
Changes between ON and OFF B
OFF Does not change between ON and OFF A
Changes between ON and OFF B


A

REPLACE MASTER CYLINDER SOLENOID

B

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

7.CHECK TERMINAL VOLTAGE (IG1)

OK

8.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)

OK

REPLACE MASTER CYLINDER SOLENOID

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI3 CIRCUIT)
a.

Disconnect the A6 skid control ECU connector.


b.

Disconnect the F47 four wheel drive control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-40 (EXI3) - Body ground Always 10 kΩ or higher




OK

10.INSPECT TERMINAL VOLTAGE (EXI3)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT TERMINAL VOLTAGE (EXI3)
a.

Disconnect the A6 skid control ECU connector.


b.

Connect the F47 four wheel drive control ECU connector.


c.
U150101E01
0.097,0.113 0.359,0.266 0.262,0.153 10 *a 2.624,0.422 2.972,0.594 0.348,0.172 10 EXI3 2.595,0.505 2.522,0.505 2.522,0.505 2.02,1.502 false 0.207,0.741 0.432,0.911 0.225,0.170 10 A6

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A6-40 (EXI3) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

REPLACE MASTER CYLINDER SOLENOID

NG

REPLACE 4 WHEEL DRIVE CONTROL ECU NO.2