If any of the following is detected, the ABS warning light remains on.
The skid control ECU connector is disconnected from the skid control ECU.
There is a malfunction in the skid control ECU internal circuit.
There is an open in the harness between the combination meter and skid control ECU.
The anti-lock brake system is defective.
The voltage at terminal IG1 is high.
The rear differential is locked.*
*: w/ Rear Differential Lock
It may not be possible to use the intelligent tester when the skid control ECU is abnormal.
When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check the skid control ECU connector connection.
The 2 connectors are securely connected.
OK
NG
Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).
CAN Bus Check indicates no malfunctions in CAN communication.
OK
NG
(See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
OK
NG
Disconnect the A6 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A6-40 (EXI3) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Skid Control ECU) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 4WD) | B |
| NG (for 2WD) | C |
A
B
C
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| ABS Warning Light | ABS warning light/ ON or OFF | OFF | - |
When performing the ABS Warning Light Active Test, check ABS Warning Light in the Data List (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| ABS Warning Light | ABS warning light | Warning light ON/OFF | Observe the combination meter. |
| Result | Proceed to | |
|---|---|---|
| Data List Display | Data List Display when Performing Active Test ON/OFF Operation | |
| ON | Does not change between ON and OFF | A |
| Changes between ON and OFF | B | |
| OFF | Does not change between ON and OFF | A |
| Changes between ON and OFF | B | |
A
B
(See pageVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
OK
NG
OK
NG
Disconnect the A6 skid control ECU connector.
Disconnect the F47 four wheel drive control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A6-40 (EXI3) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the A6 skid control ECU connector.
Connect the F47 four wheel drive control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A6-40 (EXI3) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Skid Control ECU) |
OK
NG