Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2009.08–2010.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Skid Control Buzzer Circuit  


DESCRIPTION

The skid control buzzer sounds during VSC operation.

WIRING DIAGRAM

C173348E24
1.927,1.208 2.24,1.385 0.313,0.177 10 false IG1 5.396,3.063 7.042,3.417 1.646,0.354 10 false Master Cylinder Solenoid (Skid Control ECU) 3.271,1.531 4.646,1.823 1.375,0.292 10 false Skid Control Buzzer 5.844,1.063 6.115,1.271 0.271,0.208 10 false BZ 5.406,2.906 5.677,3.083 0.271,0.177 10 false A6 5.542,0.948 5.781,1.125 0.24,0.177 10 false 30 3.188,0.938 3.365,1.156 0.177,0.219 10 false 2 4.188,0.948 4.375,1.167 0.188,0.219 10 false 1 2.354,2.063 3.792,2.375 1.438,0.313 10 false from IG1 Circuit 3.281,1.375 3.51,1.521 0.229,0.146 10 false A1 3.875,1.063 4.167,1.323 0.292,0.26 10 false BZ 3.385,1.073 3.677,1.281 0.292,0.208 10 false IG1

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BUZZER)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Buzzer Skid control buzzer Buzzer ON/OFF The buzzer can be heard.


f.

Check that the buzzer sounds/stops when turning the skid control buzzer on/off by using the intelligent tester.

Result
Result Proceed to
Buzzer sounds/stops A
Buzzer does not sound or sounds constantly B



B

2.CHECK TERMINAL VOLTAGE (IG1)

A

2.CHECK TERMINAL VOLTAGE (IG1)
a.

Disconnect the A1 skid control buzzer connector.


b.
U180940E01
1.619,0.318 1.811,0.509 0.192,0.191 10 A1 0.098,0 0.372,0.205 0.274,0.205 10 *a 2.524,1.577 2.820,1.754 0.297,0.177 10 IG1 1.972,1.379 2.642,1.478 2.642,1.478 2.642,1.556 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A1-2 (IG1) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control Buzzer)



OK

3.INSPECT SKID CONTROL BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SKID CONTROL BUZZER

b.
C361657E01
1.875,1.938 2.042,1.938 2.042,1.938 2.031,0.99 true 3.052,1.313 3.052,1.167 3.052,1.167 2.333,0.917 true 0.167,0.094 0.479,0.292 0.313,0.198 10 false *a 2.969,1.344 3.281,1.542 0.313,0.198 10 false IG1 1.667,1.854 1.979,2.052 0.313,0.198 10 false BZ

Apply battery voltage to the skid control buzzer, and check that the buzzer sounds.

OK:
Measurement Condition Specified Condition
Battery positive (+) voltage - Terminal 2 (IG1) Skid control buzzer sounds
Battery negative (-) voltage - Terminal 1 (BZ)


Text in Illustration
*a Component without harness connected
(Skid Control Buzzer)



OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - SKID CONTROL ECU)

NG

REPLACE SKID CONTROL BUZZER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - SKID CONTROL ECU)
a.

Disconnect the A6 skid control ECU connector.


b.

Disconnect the A1 skid control buzzer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-30 (BZ) - A1-1 (BZ) Always Below 1 Ω
A6-30 (BZ) - Body ground Always 10 kΩ or higher




OK

REPLACE MASTER CYLINDER SOLENOID

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR