Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2010.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Downhill Assist Control Indicator Light does not Come ON  


DESCRIPTION

Even if the downhill assist control switch is pressed, the downhill assist control indicator light blinks and downhill assist control does not activate under the following conditions:

·

The transfer is in H4.

·

The brake system is malfunctioning.

·

The temperature of the hydraulic brake booster increases and downhill assist control is temporarily canceled.


WIRING DIAGRAM

C214522E06
3.556,2.958 4.569,3.318 1.012,0.360 10 Downhill Assist Control Switch 0.96,3.538 1.562,3.874 0.603,0.335 10 Downhill Assist 5.456,3.752 5.715,3.922 0.259,0.170 10 A6 5.456,3.892 7.038,4.252 1.582,0.360 10 Master Cylinder Solenoid (Skid Control ECU) 3.556,2.799 3.800,2.997 0.244,0.198 10 U4 4.705,2.16 4.852,2.348 0.147,0.188 10 4 3.353,2.15 3.530,2.327 0.177,0.177 10 1 5.763,2.272 6.183,2.446 0.420,0.174 10 HDCS 5.462,2.178 5.655,2.394 0.193,0.216 10 44 1.366,1.258 1.679,1.419 0.313,0.161 10 IG+ 0.544,1.45 0.881,1.712 0.336,0.262 10 CPU 0.521,4.212 0.890,4.419 0.369,0.207 10 F14 0.521,4.385 1.769,4.573 1.248,0.188 10 Combination Meter 0.922,4.942 2.907,5.112 1.985,0.170 10 : CAN Communication System

CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK CAN COMMUNICATION LINE

OK

2.CHECK FOR DTC

NG

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.CHECK FOR DTC
a.

Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

3.INSPECT DOWNHILL ASSIST CONTROL SWITCH

B

3.INSPECT DOWNHILL ASSIST CONTROL SWITCH
a.

Remove the downhill assist control switch (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>DOWNHILL ASSIST CONTROL SWITCH>REMOVAL).


b.
C215496E03
0.206,0.089 0.487,0.281 0.281,0.192 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 4 Not pushed in 10 kΩ or higher
Pushed in Below 1 Ω


Text in Illustration
*a Component without harness connected
(Downhill Assist Control Switch)



OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU HDCS CIRCUIT)

NG

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU HDCS CIRCUIT)
a.

Disconnect the A6 skid control ECU connector.


b.

Disconnect the U4 downhill assist control switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-44 (HDCS) - U4-4 Always Below 1 Ω
A6-44 (HDCS) - Body ground Always 10 kΩ or higher
U4-1 - Body ground Always Below 1 Ω




OK

5.READ VALUE USING INTELLIGENT TESTER (DOWNHILL ASSIST CONTROL LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING INTELLIGENT TESTER (DOWNHILL ASSIST CONTROL LIGHT)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Downhill Assist Control Light Downhill assist control indicator light/ ON or OFF ON: Indicator light on
OFF: Indicator light off
-


f.

When performing the Downhill Assist Control Light Active Test, check Downhill Assist Control Light in the Data List (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Downhill Assist Control Light Downhill assist control indicator light Indicator light ON/OFF Observe the combination meter.


Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Does not change between ON and OFF A
Changes between ON and OFF B
OFF Does not change between ON and OFF A
Changes between ON and OFF B


A

REPLACE MASTER CYLINDER SOLENOID

B

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)