Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2010.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1401  Front Speed Sensor RH Malfunction  C1271  Low Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1272  Low Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1402  Front Speed Sensor LH Malfunction  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. These signals are used for brake control.

The speed sensor rotors have rows of alternating N and S magnetic poles and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU.

C173114E15
5.51,1.271 5.51,0.125 5.51,0.125 5.594,0.125 false 6.156,1.271 6.156,0.625 6.156,0.625 6.219,0.625 false 1.885,0.51 2.896,0.781 1.01,0.271 10 false Speed Sensor 1.51,1.323 2,1.531 0.49,0.208 10 false MRE A 1.5,1.625 1.99,1.844 0.49,0.219 10 false MRE B 2.26,1.427 2.906,1.708 0.646,0.281 10 false Sensor IC 4.01,2.042 4.677,2.26 0.667,0.219 10 false Backward 6.281,0.552 7.094,0.781 0.813,0.229 10 false High Speed 5.667,0.052 6.396,0.24 0.729,0.188 10 false Low Speed 6.698,1.292 7.094,1.5 0.396,0.208 10 false 2.6 V 6.698,1.5 7.104,1.74 0.406,0.24 10 false 1.4 V 6.698,1.75 7.115,2.021 0.417,0.271 10 false 0.7 V 5.406,2.052 6.021,2.271 0.615,0.219 10 false Forward 0.073,2.448 2.719,2.677 2.646,0.229 10 false Speed Sensor Rotor (Bearing Inner Race) 3.24,1.396 3.792,1.594 0.552,0.198 10 false to ECU 3.177,1.115 3.396,1.302 0.219,0.188 10 false (+) 3.188,1.802 3.375,1.99 0.188,0.188 10 false (-)

DTC Code DTC Detection Condition Trouble Area
C1401
C1402
One of the following conditions is met:
1.

At a vehicle speed of 10 km/h (6 mph) or more, the output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.

2.

At a vehicle speed of less than 10 km/h (6 mph), the output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

At a vehicle speed of 10 km/h (6 mph) or more, the outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more.


·

Front speed sensor RH/LH

·

Front speed sensor rotor RH/LH

·

Sensor installation


C1271
C1272
Stored only during test mode.
·

Front speed sensor RH/LH

·

Front speed sensor rotor RH/LH

·

Sensor installation



HINT:
·

DTCs C1401 and C1271 are for the front speed sensor RH.

·

DTCs C1402 and C1272 are for the front speed sensor LH.



CAUTION / NOTICE / HINT

NOTICE:

Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).


PROCEDURE

1.CHECK FRONT SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C144929E82
0.833,1.635 0.833,0.76 0.833,0.76 0.979,0.76 false 0.698,2.479 0.948,2.792 0.948,2.792 1.063,2.792 false 0.625,2.927 0.906,3.125 0.281,0.198 10 false *b 2.667,2.906 2.99,3.104 0.323,0.198 10 false *c 1.115,2.698 1.542,2.938 0.427,0.24 10 false *a 1.052,0.677 1.667,0.979 0.615,0.302 10 false 8.5 N*m 0.104,0.125 0.344,0.323 0.24,0.198 10 false *1

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)


Text in Illustration
*1 Front Speed Sensor
*a No clearance
*b OK
*c NG



OK

2.INSPECT FRONT SPEED SENSOR TIP

NG

INSTALL FRONT SPEED SENSOR CORRECTLY

2.INSPECT FRONT SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

No scratches, oil, or foreign matter on the sensor tip.


NOTICE:

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.




OK

3.INSPECT FRONT SPEED SENSOR ROTOR

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

3.INSPECT FRONT SPEED SENSOR ROTOR
a.

Remove the front axle with ABS rotor bearing assembly (for 2WD: See page Drivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB(for 2WD)>REMOVAL, for 4WD: See page Drivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB(for 4WD)>REMOVAL).


b.

Check the speed sensor rotor.

OK:

No scratches, oil, or foreign matter on the rotors.


HINT:

The front speed sensor rotor is incorporated into the front axle with ABS rotor bearing assembly.

If the front speed sensor rotor needs to be replaced, replace it together with the front axle with ABS rotor bearing assembly.




OK

4.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR ROTOR

4.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Start the engine.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Actual wheel speed No large fluctuations when driving at a constant speed.
FL Wheel Speed Front wheel speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Actual wheel speed No large fluctuations when driving at a constant speed.


f.

Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK).


OK:

The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).




OK

NG

5.REPLACE FRONT SPEED SENSOR
5.REPLACE FRONT SPEED SENSOR
a.


NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTCs C1401 and C1402 are not output A
DTCs C1401 and/or C1402 are output (for 2WD) B
DTCs C1401 and/or C1402 are output (for 4WD) C



A

END

B

REPLACE FRONT AXLE WITH ABS ROTOR BEARING ASSEMBLY

C

REPLACE FRONT AXLE WITH ABS ROTOR BEARING ASSEMBLY