Refer to DTCs C1401 and C1402 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1271).
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1407
C1408 |
Either condition is met:
1.
An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2.
With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more. |
·
Rear speed sensor RH/LH ·
Skid control sensor wire ·
Speed sensor circuit ·
Master cylinder solenoid (Skid control ECU) |
DTC C1407 is for the rear speed sensor RH.
DTC C1408 is for the rear speed sensor LH.
When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| RR Speed Open | Rear speed sensor RH open detection/ Error or Normal | Normal | - |
| RL Speed Open | Rear speed sensor LH open detection/ Error or Normal | Normal | - |
Normal (there are no momentary interruptions).
Perform the above inspection before removing the sensor and connector.
OK
NG
OK
NG
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1407 and C1408 are not output | A |
| DTCs C1407 and/or C1408 are output | B |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
| *A | for RH | *B | for LH |
| *1 | Skid Control Sensor Wire | - | - |
Remove the skid control sensor wire (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Qz1-4 - z7-2 (RR+) | Always | Below 1 Ω |
| Qz1-3 - z7-1 (RR-) | Always | Below 1 Ω |
| Qz1-4 - Qz1-3 | Always | 10 kΩ or higher |
| Qz1-4 - Qz1-1 | Always | 10 kΩ or higher |
| Qz1-4 - Qz1-2 | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Qz1-2 - z8-2 (RL+) | Always | Below 1 Ω |
| Qz1-1 - z8-1 (RL-) | Always | Below 1 Ω |
| Qz1-2 - Qz1-1 | Always | 10 kΩ or higher |
| Qz1-2 - Qz1-3 | Always | 10 kΩ or higher |
| Qz1-2 - Qz1-4 | Always | 10 kΩ or higher |
OK
NG
Install the skid control sensor wire.
Disconnect the A6 skid control ECU connector.
Disconnect the z7 and/or z8 rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A6-5 (RR+) - z7-2 (RR+) | Always | Below 1 Ω |
| A6-5 (RR+) - Body ground | Always | 10 kΩ or higher |
| A6-19 (RR-) - z7-1 (RR-) | Always | Below 1 Ω |
| A6-19 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A6-20 (RL+) - z8-2 (RL+) | Always | Below 1 Ω |
| A6-20 (RL+) - Body ground | Always | 10 kΩ or higher |
| A6-6 (RL-) - z8-1 (RL-) | Always | Below 1 Ω |
| A6-6 (RL-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the z7 and/or z8 rear speed sensor connector.
Connect the A6 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| z7-2 (RR+) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| z8-2 (RL+) - Body ground | Ignition switch ON | 11 to 14 V |
| *A | for RH |
| *B | for LH |
| *a | Front view of wire harness connector
(to Rear Speed Sensor) |
OK
NG