Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2010.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1379  Downhill Assist Control Switch Malfunction (Test Mode DTC)  


DESCRIPTION

DTC C1379 is cleared when the downhill assist control switch sends a downhill assist control operation signal or when test mode ends.

DTC Code DTC Detection Condition Trouble Area
C1379 Stored only during test mode.
·

Downhill assist control switch

·

Harness or connector

·

Master cylinder solenoid (Skid control ECU)



WIRING DIAGRAM

C214516E14
1.875,1.375 3.802,1.583 1.927,0.208 10 false Downhill Assist Control Switch 5.313,0.938 5.927,1.208 0.615,0.271 10 false HDCS 4.99,0.802 5.229,1.01 0.24,0.208 10 false 44 4.885,1.708 6.5,2.115 1.615,0.406 10 false Master Cylinder Solenoid (Skid Control ECU) 4.896,1.542 5.135,1.802 0.24,0.26 10 false A6 1.885,1.208 2.115,1.365 0.229,0.156 10 false U4 3.365,0.802 3.521,1 0.156,0.198 10 false 4 1.979,0.781 2.177,1.021 0.198,0.24 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (DOWNHILL ASSIST CONTROL SW)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Downhill Assist Control SW Downhill assist control switch / ON or OFF ON: Downhill assist control on
OFF: Downhill assist control off
-


f.

Check the Data List for proper functioning of the downhill assist control switch.

OK:

The intelligent tester displays ON or OFF according to downhill assist control switch operation.




OK

2.CHECK TEST MODE DTC

NG

3.INSPECT DOWNHILL ASSIST CONTROL SWITCH
2.CHECK TEST MODE DTC
a.

Perform the downhill assist control switch check in the Test Mode procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).

OK:

Test mode DTC C1379 is cleared.




OK

NG

REPLACE MASTER CYLINDER SOLENOID

3.INSPECT DOWNHILL ASSIST CONTROL SWITCH

OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - DOWNHILL ASSIST CONTROL SWITCH)

NG

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - DOWNHILL ASSIST CONTROL SWITCH)
a.

Disconnect the A6 skid control ECU connector.


b.

Disconnect the U4 downhill assist control switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-44 (HDCS) - U4-4 Always Below 1 Ω
A6-44 (HDCS) - Body ground Always 10 kΩ or higher
U4-1 - Body ground Always Below 1 Ω




OK

REPLACE MASTER CYLINDER SOLENOID

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR