Home › Brake › PARKING BRAKE › PARKING BRAKE SYSTEM
RM1440E _54 Brake _056146 PARKING BRAKE _0274017 PARKING BRAKE SYSTEM N

PARKING BRAKE  PARKING BRAKE SYSTEM  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT PARKING BRAKE PEDAL TRAVEL

a.

Fully depress the parking brake pedal to engage the parking brake.


b.

Depress the pedal again to disengage the parking brake.


c.

Slowly depress the parking brake pedal using the specified force and count the number of clicks.

Standard:

5 to 7 clicks at 294 N (30 kgf, 66 lbf)


If the parking brake pedal travel is not as specified, adjust the parking brake shoe clearance and parking brake pedal travel.


Hide 2.REMOVE REAR WHEEL

Hide 3.ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL

a.

Remove the lower instrument panel finish panel sub-assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL).


b.

Completely release the parking brake pedal.


c.
C361678

Loosen the lock nut and adjusting nut to completely release the parking brake cable.


d.

Temporarily install the hub nuts to the hub bolts.

HINT:

Securely install the hub nuts to the rear disc.



e.
U116387

Turn the shoe adjuster so that it expands until the disc locks.

Text in Illustration
V100135

Shoe Adjuster Contracts
V100136

Shoe Adjuster Expands


f.

Turn the shoe adjuster so that it contracts until the disc can rotate smoothly.

Standard:

8 notches



g.

Check that there is no brake drag against the shoe.


h.
U116068E04
1.292,1.292 2.01,1.292 false 2.063,1.208 2.229,1.375 0.167,0.167 10 false *1

Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

Standard:

5 to 7 clicks at 294 N (30 kgf, 66 lbf)


Text in Illustration
*1 Adjusting Nut


i.

Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


j.

Operate the parking brake pedal 3 to 4 times and check the parking brake pedal travel.


k.

Check that there is no brake drag against the shoe.


l.
C215295

Additionally, excessive pedal travel can be adjusted on the No. 1 parking brake cable as follows.

i.

Loosen the No. 1 parking brake cable lock nut.


ii.

Turn the No. 1 parking brake cable adjustment nut until the parking brake pedal travel is correct.

Standard:

5 to 7 clicks at 294 N (30 kgf, 66 lbf)



iii.

Tighten the No. 1 parking brake cable lock nut.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Pay attention that the adjustment nut does not rotate together with the lock nut during tightening.



iv.

Depress and release the parking brake pedal 3 or 4 times. Then check the number of clicks when depressing the pedal.

Standard:

5 to 7 clicks


If the result is not as specified, adjust the parking brake pedal travel again.



m.

Remove the hub nuts from the hub bolts.


n.

Install the lower instrument panel finish panel sub-assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION).


o.

When operating the parking brake lever, check that the brake warning light comes on.

OK:

The brake warning light always illuminates at the first click.