Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › from 2013.08
RM1440E _56 Audio / Visual / Telematics _056150 AUDIO / VIDEO _0274026 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Speaker Circuit  


DESCRIPTION

If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.

If a short is detected in a speaker circuit, no sound can be heard from the speakers.

WIRING DIAGRAM

E283441E06
5.854,5.26 6.271,5.469 0.417,0.208 10 false RR- 5.854,3.865 6.271,4.073 0.417,0.208 10 false RR+ 5.854,7.281 6.271,7.49 0.417,0.208 10 false RL- 5.854,5.854 6.271,6.063 0.417,0.208 10 false RL+ 5.844,1.313 6.26,1.521 0.417,0.208 10 false FR- 5.854,0.333 6.271,0.542 0.417,0.208 10 false FR+ 5.854,3.292 6.271,3.5 0.417,0.208 10 false FL- 5.854,2.333 6.271,2.542 0.417,0.208 10 false FL+ 5.552,5.063 5.854,5.271 0.302,0.208 10 false 3 5.552,3.667 5.854,3.875 0.302,0.208 10 false 1 5.552,7.094 5.854,7.302 0.302,0.208 10 false 6 5.552,5.677 5.854,5.885 0.302,0.208 10 false 2 5.552,1.125 5.854,1.333 0.302,0.208 10 false 5 5.552,0.156 5.854,0.365 0.302,0.208 10 false 1 5.552,3.115 5.854,3.323 0.302,0.208 10 false 6 5.552,2.156 5.854,2.365 0.302,0.208 10 false 2 5.469,5.271 5.771,5.479 0.302,0.208 10 false G35 5.469,3.865 5.771,4.073 0.302,0.208 10 false G35 5.469,7.271 5.771,7.479 0.302,0.208 10 false G35 5.469,5.865 5.771,6.073 0.302,0.208 10 false G35 5.458,1.313 5.76,1.521 0.302,0.208 10 false G36 5.458,0.344 5.813,0.552 0.354,0.208 10 false G36 5.469,3.292 5.771,3.5 0.302,0.208 10 false G36 4.583,1.198 4.844,1.406 0.26,0.208 10 false - 4.583,0.26 4.844,0.469 0.26,0.208 10 false + 2.49,1.208 3.042,1.417 0.552,0.208 10 false TWR- 2.5,0.25 3.052,0.458 0.552,0.208 10 false TWR+ 4.583,3.188 4.844,3.396 0.26,0.208 10 false - 4.583,2.25 4.844,2.458 0.26,0.208 10 false + 4.771,1.219 4.917,1.427 0.146,0.208 10 false 3 4.76,0.26 4.927,0.469 0.167,0.208 10 false 1 2.281,1.208 2.427,1.417 0.146,0.208 10 false 4 2.281,0.25 2.448,0.458 0.167,0.208 10 false 2 4.792,3.198 4.938,3.406 0.146,0.208 10 false 3 4.781,2.24 4.948,2.448 0.167,0.208 10 false 1 2.281,3.188 2.427,3.396 0.146,0.208 10 false 4 2.281,2.25 2.448,2.458 0.167,0.208 10 false 2 2.5,3.198 3.052,3.406 0.552,0.208 10 false TWL- 2.5,2.25 3.052,2.458 0.552,0.208 10 false TWL+ 3.292,0.667 4.625,1.063 1.333,0.396 10 false Front No. 2 Speaker Assembly RH 0.354,4.875 0.719,5.115 0.365,0.24 10 false W5 0.354,3.875 0.719,4.115 0.365,0.24 10 false J1 0.354,6.896 0.719,7.135 0.365,0.24 10 false W6 0.354,5.885 0.719,6.125 0.365,0.24 10 false K1 0.354,0.625 0.719,0.865 0.365,0.24 10 false H1 0.354,0.813 1.698,1.219 1.344,0.406 10 false Front No. 1 Speaker Assembly RH 0.354,2.625 0.719,2.865 0.365,0.24 10 false I1 3.302,2.615 4.635,3.01 1.333,0.396 10 false Front No. 2 Speaker Assembly LH 0.354,2.771 1.698,3.177 1.344,0.406 10 false Front No. 1 Speaker Assembly LH 3.281,0.479 3.646,0.719 0.365,0.24 10 false G12 3.302,2.448 3.667,2.688 0.365,0.24 10 false G1 0.344,5.052 1.76,5.479 1.417,0.427 10 false Rear No. 2 Speaker Assembly RH 0.354,4.031 1.688,4.458 1.333,0.427 10 false Rear Speaker Assembly RH 0.354,7.063 1.771,7.49 1.417,0.427 10 false Rear No. 2 Speaker Assembly LH 0.354,6.073 1.479,6.5 1.125,0.427 10 false Rear Speaker Assembly LH 5.698,7.729 7.031,8.156 1.333,0.427 10 false Radio and Display Receiver Assembly 1.844,5.365 2.021,5.563 0.177,0.198 10 false 2 1.833,4.813 2.01,5.01 0.177,0.198 10 false 1 1.844,4.365 2.021,4.563 0.177,0.198 10 false 2 1.844,3.802 2.021,4 0.177,0.198 10 false 1 1.844,7.354 2.021,7.552 0.177,0.198 10 false 2 1.844,6.792 2.021,6.99 0.177,0.198 10 false 1 1.844,6.375 2.021,6.573 0.177,0.198 10 false 2 1.844,5.813 2.021,6.01 0.177,0.198 10 false 1 1.844,1.094 2.021,1.292 0.177,0.198 10 false 2 1.833,0.573 2.01,0.771 0.177,0.198 10 false 1 1.844,3.094 2.021,3.292 0.177,0.198 10 false 2 1.844,2.552 2.021,2.75 0.177,0.198 10 false 1 5.469,2.344 5.771,2.552 0.302,0.208 10 false G36

PROCEDURE

1.CHECK SPEAKER (OPERATION CHECK)
a.
E268474

Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK).


b.

Perform the operation check above and determine the speaker that is not operating.

Result:
Not Operating Speaker Proceed to
Front No. 1 speaker assembly or front No. 2 speaker assembly A
Rear speaker assembly or rear No. 2 speaker assembly B


HINT:

If sound cannot be heard from any speaker, inspect all of them.




A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - FRONT NO. 1 SPEAKER - FRONT NO. 2 SPEAKER)

B

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - REAR SPEAKER - REAR NO. 2 SPEAKER))
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - FRONT NO. 1 SPEAKER - FRONT NO. 2 SPEAKER)
a.

Disconnect the G36 radio and display receiver assembly connector.


b.

Disconnect the H1 and I1 front No. 1 speaker assembly connectors.


c.

Disconnect the G1 and G12 front No. 2 speaker assembly connectors.


d.

Measure the resistance between each of the front No. 2 speaker assemblies and the radio and display receiver assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
G36-1 (FR+) - G12-1 (+) Always Below 1 Ω
G36-2 (FL+) - G1-1 (+) Always Below 1 Ω
G36-5 (FR-) - G12-3 (-) Always Below 1 Ω
G36-6 (FL-) - G1-3 (-) Always Below 1 Ω



e.

Measure the resistance between each of the front No. 1 speaker assemblies and the front No. 2 speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-2 (TWL+) - I1-1 Always Below 1 Ω
G1-4 (TWL-) - I1-2 Always Below 1 Ω
G12-2 (TWR+) - H1-1 Always Below 1 Ω
G12-4 (TWR-) - H1-2 Always Below 1 Ω



f.

Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
G36-1 (FR+) - Body ground Always 10 kΩ or higher
G36-2 (FL+) - Body ground Always 10 kΩ or higher
G36-5 (FR-) - Body ground Always 10 kΩ or higher
G36-6 (FL-) - Body ground Always 10 kΩ or higher



g.

Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-2 (TWL+) - Body ground Always 10 kΩ or higher
G1-4 (TWL-) - Body ground Always 10 kΩ or higher
G12-2 (TWR+) - Body ground Always 10 kΩ or higher
G12-4 (TWR-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.
U150433E03
0.156,0.052 0.333,0.219 0.177,0.167 10 false *a 0.427,1.073 0.719,1.229 0.292,0.156 10 false H1 0.469,1.49 0.76,1.646 0.292,0.156 10 false I1 0.938,0.99 1.115,1.156 0.177,0.167 10 false *b 0.938,1.417 1.115,1.583 0.177,0.167 10 false *c

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H1-1 - H1-2 Always 4 Ω
I1-1 - I1-2 Always 4 Ω


Text in Illustration
*a Component without harness connected
(Front No. 1 Speaker Assembly)
*b for RH
*c for LH



OK

4.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

4.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
a.

Check that the malfunction disappears when a known good speaker is installed (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL).

OK:

Malfunction disappears.


HINT:
·

Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

·

When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.

·

Perform the above inspection on both LH and RH sides.





OK

END (FRONT NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE)

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - REAR SPEAKER - REAR NO. 2 SPEAKER))
a.

Disconnect the G35 radio and display receiver assembly connector.


b.

Disconnect the J1 and K1 rear speaker assembly connectors.


c.

Disconnect the W5 and W6 rear No. 2 speaker assembly connectors.


d.

Measure the resistance between each of the rear speaker assemblies and the radio and display receiver assembly, the rear No. 2 speaker assemblies and the display receiver assembly, and the rear speaker assemblies and the rear No. 2 speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
G35-1 (RR+) - J1-1 Always Below 1 Ω
G35-2 (RL+) -K1-1 Always Below 1 Ω
G35-3 (RR-) - W5-2 Always Below 1 Ω
G35-6 (RL-) -W6-2 Always Below 1 Ω
J1-2 - W5-1 Always Below 1 Ω
K1-2 - W6-1 Always Below 1 Ω



e.

Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
G35-1 (RR+) - Body ground Always 10 kΩ or higher
G35-2 (RL+) - Body ground Always 10 kΩ or higher
G35-3 (RR-) - Body ground Always 10 kΩ or higher
G35-6 (RL-) - Body ground Always 10 kΩ or higher



f.

Measure the resistance between the rear No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-2 - Body ground Always 10 kΩ or higher
K1-2 - Body ground Always 10 kΩ or higher




OK

6.INSPECT REAR SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT REAR SPEAKER ASSEMBLY
a.
U150434E03
0.156,0.052 0.333,0.219 0.177,0.167 10 false *a 0.448,1.063 0.74,1.219 0.292,0.156 10 false J1 0.438,1.479 0.729,1.635 0.292,0.156 10 false K1 0.938,0.99 1.115,1.156 0.177,0.167 10 false *b 0.938,1.417 1.115,1.583 0.177,0.167 10 false *c

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-1 - J1-2 Always 4 Ω
K1-1 - K1-2 Always 4 Ω


Text in Illustration
*a Component without harness connected
(Rear No. 1 Speaker Assembly)
*b for RH
*c for LH



OK

7.INSPECT REAR NO. 2 SPEAKER ASSEMBLY

NG

7.INSPECT REAR NO. 2 SPEAKER ASSEMBLY
a.
U150435E03
0.156,0.052 0.333,0.219 0.177,0.167 10 false *a 0.417,1.063 0.708,1.219 0.292,0.156 10 false W5 0.417,1.479 0.708,1.635 0.292,0.156 10 false W6 0.938,0.99 1.115,1.156 0.177,0.167 10 false *b 0.938,1.417 1.115,1.583 0.177,0.167 10 false *c

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W5-1 - W5-2 Always 4 Ω
W6-1 - W6-2 Always 4 Ω


Text in Illustration
*a Component without harness connected
(Rear No. 2 Speaker Assembly)
*b for RH
*c for LH



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE REAR NO. 2 SPEAKER ASSEMBLY